Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/ Secondary Air Injection System) › from 2017.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0327320 SFI SYSTEM(w/ Secondary Air Injection System) C

3UR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  P0355  Ignition Coil "E" Primary / Secondary Circuit  P0356  Ignition Coil "F" Primary / Secondary Circuit  P0357  Ignition Coil "G" Primary / Secondary Circuit  P0358  Ignition Coil "H" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is output, check the No. 1 ignition coil circuit.

·

If DTC P0352 is output, check the No. 2 ignition coil circuit.

·

If DTC P0353 is output, check the No. 3 ignition coil circuit.

·

If DTC P0354 is output, check the No. 4 ignition coil circuit.

·

If DTC P0355 is output, check the No. 5 ignition coil circuit.

·

If DTC P0356 is output, check the No. 6 ignition coil circuit.

·

If DTC P0357 is output, check the No. 7 ignition coil circuit.

·

If DTC P0358 is output, check the No. 8 ignition coil circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A147863E34
0.094,5.604 1.948,7.354 1.854,1.75 5.135,0.719 5.469,0.302 false 0.417,2.292 1.688,2.656 1.271,0.365 10 false Crankshaft Position Sensor 0.417,3.469 1.24,3.677 0.823,0.208 10 false VVT Sensor 0.417,4.625 1.625,5 1.208,0.375 10 false Camshaft Position Sensor 2.365,8.083 2.844,8.281 0.479,0.198 10 false ECM 2.531,0.896 2.969,1.094 0.438,0.198 10 false IGT1 2.531,1.302 2.969,1.5 0.438,0.198 10 false IGF1 2.531,2.281 2.969,2.479 0.438,0.198 10 false IGT2 2.531,2.698 2.969,2.896 0.438,0.198 10 false IGF2 2.531,3.177 2.969,3.375 0.438,0.198 10 false IGT3 2.531,4.052 2.969,4.25 0.438,0.198 10 false IGT4 2.531,4.906 2.969,5.104 0.438,0.198 10 false IGT5 2.531,5.792 2.969,5.99 0.438,0.198 10 false IGT6 2.531,6.677 2.969,6.875 0.438,0.198 10 false IGT7 2.531,7.542 2.969,7.74 0.438,0.198 10 false IGT8 1.813,7.698 2.25,7.896 0.438,0.198 10 false TACH 3.854,0.417 4.333,0.615 0.479,0.198 10 false Igniter 4.302,0.083 5.198,0.281 0.896,0.198 10 false from Battery 4.365,1.844 5.302,2.042 0.938,0.198 10 false Ignition Coil 5.531,0.198 6.646,0.396 1.115,0.198 10 false No. 1 Ignition Coil 5.531,1.083 6.5,1.281 0.969,0.198 10 false No. 1 Cylinder 5.531,2.719 6.781,2.917 1.25,0.198 10 false No. 2 Cylinder 5.531,3.583 6.781,3.781 1.25,0.198 10 false No. 3 Cylinder 5.531,4.448 6.781,4.646 1.25,0.198 10 false No. 4 Cylinder 5.531,5.333 6.781,5.531 1.25,0.198 10 false No. 5 Cylinder 5.531,6.208 6.781,6.406 1.25,0.198 10 false No. 6 Cylinder 5.531,7.135 6.781,7.333 1.25,0.198 10 false No. 7 Cylinder 5.531,8 6.781,8.198 1.25,0.198 10 false No. 8 Cylinder 5.927,1.656 6.823,1.854 0.896,0.198 10 false Spark Plug 3.906,2.406 5.406,2.604 1.5,0.198 10 false No. 2 Ignition Coil 3.906,3.344 5.406,3.542 1.5,0.198 10 false No. 3 Ignition Coil 3.906,4.219 5.406,4.417 1.5,0.198 10 false No. 4 Ignition Coil 3.906,5.125 5.406,5.323 1.5,0.198 10 false No. 5 Ignition Coil 3.906,5.927 5.406,6.125 1.5,0.198 10 false No. 6 Ignition Coil 3.906,6.802 5.406,7 1.5,0.198 10 false No. 7 Ignition Coil 3.906,7.698 5.406,7.896 1.5,0.198 10 false No. 8 Ignition Coil 1.208,7.531 1.75,7.74 0.542,0.208 10 false to DLC3 0.125,5.635 1.927,6.688 1.802,1.052 10 true Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter, Throttle Position Sensor, etc.) 0.073,0.021 2.573,0.323 2.5,0.302 12 false Reference (System Diagram):

DTC Code DTC Detection Condition Trouble Area
P0351
P0352
P0353
P0354
P0355
P0356
P0357
P0358
No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT circuit (1 to 8) between ignition coil and ECM

·

No. 1 to No. 8 ignition coils

·

ECM



Reference: Inspection using an oscilloscope.

A385685E02
0.646,0.135 1.177,0.333 0.531,0.198 10 false 2 V/DIV. 0.906,0.646 1.24,0.833 0.333,0.188 10 false IGT 0.917,1.26 1.25,1.448 0.333,0.188 10 false IGF 0.635,0.885 1.052,1.083 0.417,0.198 10 false GND 0.656,1.458 1.073,1.656 0.417,0.198 10 false GND 1.781,1.792 2.896,2.042 1.115,0.25 10 false 20 msec./DIV.

Standard:
Tester Connection Tool Setting Condition Specified Condition
C45-37 (IGT1) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C45-36 (IGT2) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C45-35 (IGT3) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C45-34 (IGT4) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C45-33 (IGT5) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C45-32 (IGT6) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C45-31 (IGT7) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C45-30 (IGT8) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C45-54 (IGF1) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C45-53 (IGF2) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown


HINT:

While cranking or idling the engine, check the waveform between terminals IGT (1 to 8) and E1, and IGF1 or IGF2 and E1 of the ECM connector.



MONITOR DESCRIPTION

A115898E06
4.429,2.379 6.230,2.562 1.802,0.184 10 Ignition Coil with Igniter 4.099,1.543 4.762,1.727 0.663,0.184 10 Igniter 5.311,1.368 6.259,1.531 0.948,0.163 10 Ignition Coil 0.305,2.903 1.439,3.267 1.134,0.364 10 Ignition Signal (IGT) 0.312,3.625 1.365,4.148 1.053,0.523 10 Ignition Confirmation Signal (IGF) 1.592,3.512 2.150,3.689 0.559,0.177 10 Normal 1.367,3.898 2.148,4.074 0.781,0.177 10 Malfunction 3.483,4.521 4.430,4.708 0.948,0.187 10 Circuit Open 5.806,4.986 6.330,5.148 0.524,0.163 10 Time 1.786,1.67 2.185,1.844 0.398,0.175 10 ECM 2.9,1.338 3.226,1.524 0.326,0.186 10 IGT 2.9,1.752 3.226,1.938 0.326,0.186 10 IGF

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores DTC(s).

If the malfunction is not repaired successfully, a DTC is stored 1 second after the engine is next started.

WIRING DIAGRAM

A218112E10
5.409,0.742 5.746,0.912 0.336,0.170 10 IGT1 3.504,0.838 3.840,1.008 0.336,0.170 10 IGT1 5.409,2.409 5.746,2.579 0.336,0.170 10 IGT3 5.409,4.077 5.746,4.246 0.336,0.170 10 IGT5 5.409,5.744 5.746,5.914 0.336,0.170 10 IGT7 5.411,1.151 5.742,1.320 0.331,0.169 10 IGF1 3.509,1.247 3.840,1.416 0.331,0.169 10 IGF1 5.986,6.373 6.280,6.529 0.295,0.156 10 C45 5.182,0.754 5.366,0.909 0.184,0.156 10 37 5.182,2.421 5.366,2.577 0.184,0.156 10 35 5.182,4.088 5.366,4.244 0.184,0.156 10 33 5.182,5.755 5.366,5.911 0.184,0.156 10 31 5.182,1.158 5.449,1.314 0.267,0.156 10 54 5.977,6.527 6.341,6.711 0.364,0.184 10 ECM 3.9,0.746 4.014,0.902 0.114,0.156 10 3 3.903,1.142 4.038,1.305 0.135,0.163 10 2 2.937,0.746 3.038,0.902 0.100,0.156 10 1 2.943,1.142 3.058,1.298 0.114,0.156 10 4 2.887,1.494 3.182,1.650 0.295,0.156 10 C4 2.887,1.663 4.057,1.832 1.170,0.170 10 No. 1 Ignition Coil 3.112,0.838 3.323,0.992 0.211,0.154 10 +B 3.112,1.247 3.462,1.402 0.350,0.156 10 GND 3.504,2.519 3.840,2.689 0.336,0.170 10 IGT3 3.509,2.912 3.840,3.081 0.331,0.169 10 IGF2 3.9,2.427 4.014,2.583 0.114,0.156 10 3 3.903,2.824 4.038,2.986 0.135,0.163 10 2 2.937,2.427 3.038,2.583 0.100,0.156 10 1 2.943,2.824 3.058,2.979 0.114,0.156 10 4 2.887,3.176 3.182,3.332 0.295,0.156 10 C6 2.887,3.344 4.057,3.514 1.170,0.170 10 No. 3 Ignition Coil 3.112,2.519 3.323,2.673 0.211,0.154 10 +B 3.112,2.912 3.462,3.068 0.350,0.156 10 GND 3.504,4.173 3.840,4.342 0.336,0.170 10 IGT5 3.509,4.579 3.840,4.748 0.331,0.169 10 IGF2 3.9,4.094 4.014,4.250 0.114,0.156 10 3 3.903,4.491 4.038,4.654 0.135,0.163 10 2 2.937,4.094 3.038,4.250 0.100,0.156 10 1 2.943,4.491 3.058,4.647 0.114,0.156 10 4 2.887,4.843 3.182,4.999 0.295,0.156 10 C8 2.887,5.011 4.057,5.181 1.170,0.170 10 No. 5 Ignition Coil 3.112,4.173 3.323,4.326 0.211,0.154 10 +B 3.112,4.579 3.462,4.735 0.350,0.156 10 GND 3.504,5.854 3.840,6.024 0.336,0.170 10 IGT7 3.509,6.246 3.840,6.415 0.331,0.169 10 IGF1 3.9,5.762 4.014,5.918 0.114,0.156 10 3 3.903,6.158 4.038,6.321 0.135,0.163 10 2 2.937,5.762 3.038,5.918 0.100,0.156 10 1 2.943,6.158 3.058,6.314 0.114,0.156 10 4 2.887,6.51 3.182,6.666 0.295,0.156 10 C51 2.887,6.678 4.057,6.848 1.170,0.170 10 No. 7 Ignition Coil 3.112,5.854 3.323,6.008 0.211,0.154 10 +B 3.112,6.246 3.462,6.402 0.350,0.156 10 GND 1.718,0.444 1.966,0.600 0.248,0.156 10 INJ 0.214,0.033 1.194,0.217 0.980,0.184 10 from IG2 Relay 0.312,7.463 0.440,7.633 0.128,0.170 10 A 1.588,7.463 1.716,7.633 0.128,0.170 10 B 4.614,7.463 4.742,7.633 0.128,0.170 10 C 4.852,7.463 4.980,7.633 0.128,0.170 10 D

A372448E01
5.43,0.826 5.798,0.992 0.368,0.165 10 IGT2 5.43,2.493 5.798,2.659 0.368,0.165 10 IGT4 5.43,4.175 5.798,4.340 0.368,0.165 10 IGT6 5.43,5.828 5.798,5.993 0.368,0.165 10 IGT8 5.43,1.223 5.780,1.407 0.350,0.184 10 IGF2 5.995,6.605 6.290,6.770 0.295,0.165 10 C45 5.171,0.827 5.382,1.001 0.211,0.174 10 36 5.175,1.223 5.452,1.388 0.276,0.165 10 53 5.194,2.493 5.382,2.654 0.188,0.161 10 34 5.194,4.175 5.382,4.335 0.188,0.161 10 32 5.194,5.828 5.382,5.989 0.188,0.161 10 30 3.93,0.859 4.049,1.015 0.119,0.156 10 3 3.93,1.251 4.049,1.407 0.119,0.156 10 2 2.95,0.859 3.050,1.023 0.100,0.164 10 1 2.935,1.251 3.054,1.426 0.119,0.174 10 4 3.51,0.934 3.870,1.099 0.360,0.165 10 IGT2 3.128,0.934 3.349,1.090 0.221,0.156 10 +B 3.128,1.335 3.469,1.491 0.341,0.156 10 GND 3.52,1.335 3.870,1.491 0.350,0.156 10 IGF2 3.93,2.521 4.049,2.677 0.119,0.156 10 3 3.93,2.914 4.049,3.070 0.119,0.156 10 2 2.95,2.521 3.050,2.685 0.100,0.164 10 1 2.935,2.914 3.054,3.088 0.119,0.174 10 4 3.51,2.61 3.870,2.775 0.360,0.165 10 IGT4 3.127,2.61 3.348,2.766 0.221,0.156 10 +B 3.127,3.012 3.468,3.168 0.341,0.156 10 GND 3.52,3.012 3.870,3.168 0.350,0.156 10 IGF1 3.93,4.184 4.049,4.340 0.119,0.156 10 3 3.93,4.576 4.049,4.732 0.119,0.156 10 2 2.95,4.184 3.050,4.348 0.100,0.164 10 1 2.935,4.576 3.054,4.751 0.119,0.174 10 4 3.51,4.273 3.870,4.438 0.360,0.165 10 IGT6 3.127,4.282 3.348,4.438 0.221,0.156 10 +B 3.127,4.674 3.468,4.830 0.341,0.156 10 GND 3.52,4.674 3.870,4.830 0.350,0.156 10 IGF1 3.93,5.856 4.049,6.012 0.119,0.156 10 3 3.93,6.248 4.049,6.404 0.119,0.156 10 2 2.95,5.856 3.050,6.020 0.100,0.164 10 1 2.935,6.248 3.054,6.423 0.119,0.174 10 4 3.51,5.945 3.870,6.110 0.360,0.165 10 IGT8 3.127,5.945 3.348,6.101 0.221,0.156 10 +B 3.127,6.332 3.468,6.488 0.341,0.156 10 GND 3.52,6.332 3.870,6.488 0.350,0.156 10 IGF2 5.995,6.748 6.336,6.913 0.341,0.165 10 ECM 0.334,0.037 0.473,0.202 0.139,0.165 10 A 1.604,0.037 1.743,0.202 0.139,0.165 10 B 4.621,0.037 4.760,0.202 0.139,0.165 10 C 4.864,0.037 5.003,0.202 0.139,0.165 10 D 2.938,1.6 3.251,1.765 0.313,0.165 10 C15 2.938,1.75 4.084,1.933 1.147,0.184 10 No. 2 Ignition Coil 2.938,3.281 3.251,3.446 0.313,0.165 10 C13 2.938,3.431 4.084,3.614 1.147,0.184 10 No. 4 Ignition Coil 2.938,4.944 3.251,5.109 0.313,0.165 10 C11 2.938,5.093 4.084,5.277 1.147,0.184 10 No. 6 Ignition Coil 2.938,6.607 3.251,6.772 0.313,0.165 10 C53 2.938,6.756 4.084,6.940 1.147,0.184 10 No. 8 Ignition Coil

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)
U162853E01
0.092,0.103 2.444,0.458 2.353,0.355 10 Front view of wire harness connector: (to Ignition Coil with Igniter) 0.214,2.503 0.491,2.645 0.278,0.142 10 C11 0.645,2.167 0.921,2.309 0.276,0.142 10 C51 0.244,2.16 0.521,2.302 0.276,0.142 10 C8 0.65,2.498 0.927,2.640 0.276,0.142 10 C53 0.248,1.502 0.526,1.644 0.278,0.142 10 C4 0.645,1.502 0.921,1.644 0.276,0.142 10 C13 0.244,1.839 0.521,1.981 0.276,0.142 10 C6 0.65,1.834 0.927,1.976 0.276,0.142 10 C15 1.032,2.676 1.436,2.813 0.404,0.137 10 +B (+) 1.937,2.676 2.526,2.813 0.589,0.137 10 GND (-) 1.341,2.154 1.303,2.635 false 2.132,2.111 2.193,2.624 false

a.

Disconnect the C4, C6, C8, C11, C13, C15, C51 or C53 ignition coil connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C4-4 (GND) - Body ground Always Below 1 Ω
C15-4 (GND) - Body ground Always Below 1 Ω
C6-4 (GND) - Body ground Always Below 1 Ω
C13-4 (GND) - Body ground Always Below 1 Ω
C8-4 (GND) - Body ground Always Below 1 Ω
C11-4 (GND) - Body ground Always Below 1 Ω
C51-4 (GND) - Body ground Always Below 1 Ω
C53-4 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C4-1 (+B) - C4-4 (GND) Engine switch on (IG) 11 to 14 V
C15-1 (+B) - C15-4 (GND) Engine switch on (IG) 11 to 14 V
C6-1 (+B) - C6-4 (GND) Engine switch on (IG) 11 to 14 V
C13-1 (+B) - C13-4 (GND) Engine switch on (IG) 11 to 14 V
C8-1 (+B) - C8-4 (GND) Engine switch on (IG) 11 to 14 V
C11-1 (+B) - C11-4 (GND) Engine switch on (IG) 11 to 14 V
C51-1 (+B) - C51-4 (GND) Engine switch on (IG) 11 to 14 V
C53-1 (+B) - C53-4 (GND) Engine switch on (IG) 11 to 14 V




OK

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the C4, C6, C8, C11, C13, C15, C51 or C53 ignition coil connector.


b.

Disconnect the C45 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C4-2 (IGF1) - C45-54 (IGF1) Always Below 1 Ω
C15-2 (IGF2) - C45-53 (IGF2) Always Below 1 Ω
C6-2 (IGF2) - C45-53 (IGF2) Always Below 1 Ω
C13-2 (IGF1) - C45-54 (IGF1) Always Below 1 Ω
C8-2 (IGF2) - C45-53 (IGF2) Always Below 1 Ω
C11-2 (IGF1) - C45-54 (IGF1) Always Below 1 Ω
C51-2 (IGF1) - C45-54 (IGF1) Always Below 1 Ω
C53-2 (IGF2) - C45-53 (IGF2) Always Below 1 Ω
C4-3 (IGT1) - C45-37 (IGT1) Always Below 1 Ω
C15-3 (IGT2) - C45-36 (IGT2) Always Below 1 Ω
C6-3 (IGT3) - C45-35 (IGT3) Always Below 1 Ω
C13-3 (IGT4) - C45-34 (IGT4) Always Below 1 Ω
C8-3 (IGT5) - C45-33 (IGT5) Always Below 1 Ω
C11-3 (IGT6) - C45-32 (IGT6) Always Below 1 Ω
C51-3 (IGT7) - C45-31 (IGT7) Always Below 1 Ω
C53-3 (IGT8) - C45-30 (IGT8) Always Below 1 Ω
C4-2 (IGF1) or C45-54 (IGF1) - Body ground Always 10 kΩ or higher
C15-2 (IGF2) or C45-53 (IGF2) - Body ground Always 10 kΩ or higher
C6-2 (IGF2) or C45-53 (IGF2) - Body ground Always 10 kΩ or higher
C13-2 (IGF1) or C45-54 (IGF1) - Body ground Always 10 kΩ or higher
C8-2 (IGF2) or C45-53 (IGF2) - Body ground Always 10 kΩ or higher
C11-2 (IGF1) or C45-54 (IGF1) - Body ground Always 10 kΩ or higher
C51-2 (IGF1) or C45-54 (IGF1) - Body ground Always 10 kΩ or higher
C53-2 (IGF2) or C45-53 (IGF2) - Body ground Always 10 kΩ or higher
C4-3 (IGT1) or C45-37 (IGT1) - Body ground Always 10 kΩ or higher
C15-3 (IGT2) or C45-36 (IGT2) - Body ground Always 10 kΩ or higher
C6-3 (IGT3) or C45-35 (IGT3) - Body ground Always 10 kΩ or higher
C13-3 (IGT4) or C45-34 (IGT4) - Body ground Always 10 kΩ or higher
C8-3 (IGT5) or C45-33 (IGT5) - Body ground Always 10 kΩ or higher
C11-3 (IGT6) or C45-32 (IGT6) - Body ground Always 10 kΩ or higher
C51-3 (IGT7) or C45-31 (IGT7) - Body ground Always 10 kΩ or higher
C53-3 (IGT8) or C45-30 (IGT8) - Body ground Always 10 kΩ or higher




OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355, P0356, P0357 OR P0358)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355, P0356, P0357 OR P0358)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.



d.

Shuffle the arrangement of the ignition coils (among No. 1 to No. 8 cylinders).

NOTICE:

Do not shuffle the connectors.



e.

Perform a simulation test.


f.

Check DTCs displayed on the tester.

Result
Result Proceed to
Same DTC is output A
Different ignition coil DTC is output B



A

B