Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) › from 2017.08
RM2660E _52 Drivetrain _066407 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0327282 AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) J

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)  Pattern Select Switch 2nd Start Mode Circuit  


DESCRIPTION

When 2nd mode is selected with the ECT 2nd switch (integration control and panel assembly), the ECM controls the solenoid valves and the transmission starts from 2nd gear.

The 2nd mode is the system that operates the throttle motor to control engine output to reduce skidding of the driving wheels, and guarantee takeoff acceleration, driving straightness and turning stability.

When the shift lever is in D, the transmission automatically shifts up through 3rd to 6th as usual.

CAUTION / NOTICE / HINT

When the ECT 2nd switch is pushed, switch contact is made and 2nd mode is selected. To cancel 2nd mode, push the ECT 2nd switch once again.

HINT:

2nd mode is automatically canceled when the engine switch is turned off.


PROCEDURE

1.DRIVING TEST
HINT:

The driving test should be performed on a paved road (nonskid road).


a.

Start the engine.


b.

Turn the ECT 2nd switch off (normal drive mode).


c.

Confirm vehicle response by driving from a parked position to fully depressing the accelerator pedal.


d.

Turn the ECT 2nd switch on and perform the same check as above.

When driving the vehicle with the ECT 2nd switch on and off, check that there is a difference in acceleration.

OK:

There is a difference in acceleration.




OK

NG

2.INSPECT ECT 2ND SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY)
2.INSPECT ECT 2ND SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY)
a.
C331266E33
1.76,1.448 2.438,1.802 true 0.677,0.958 1.208,1.094 true 0.125,0.052 0.406,0.229 0.281,0.177 10 false *a 2.521,1.74 2.875,1.927 0.354,0.188 10 false 2ND 0.521,0.854 0.75,1.042 0.229,0.188 10 false E

Remove the integration control and panel assembly (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>COMBINATION SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (2ND) - 5 (E) ECT 2nd switch on Below 1 Ω
8 (2ND) - 5 (E) ECT 2nd switch off 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Integration Control and Panel Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL ASSEMBLY - BODY GROUND)

NG

REPLACE INTEGRATION CONTROL AND PANEL ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL ASSEMBLY - BODY GROUND)
a.
U165550E04
2.604,0.688 2.021,0.969 true 0.125,0.052 0.406,0.229 0.281,0.177 10 false *a 2.698,0.604 2.906,0.792 0.208,0.188 10 false E 0.521,0.865 0.875,1.042 0.354,0.177 10 false V9

Disconnect the integration control and panel assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V9-5 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Integration Control and Panel Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL ASSEMBLY - ECM)
U164949E04
1.531,1.698 1.813,0.927 true 0.063,0 0.375,0.198 0.313,0.198 10 false *a 1.229,1.74 2.083,1.969 0.854,0.229 10 false 12 (SNWI) 1.667,0.271 2.042,0.5 0.375,0.229 10 false A38

a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A38-12 (SNWI) - Body ground ECT 2nd switch on Below 1 Ω
A38-12 (SNWI) - Body ground ECT 2nd switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR