Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0327  Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)  P0328  Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)  P0332  Knock Sensor 2 Circuit Low Input (Bank 2)  P0333  Knock Sensor 2 Circuit High Input (Bank 2)  


DESCRIPTION

Flat-type knock sensors (non-resonant type) have structures that can detect vibrations between approximately 5 kHz and 15 kHz.

2 knock sensors are fitted onto the engine block to detect engine knocking.

Each knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.

The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No. DTC Detection Condition Trouble Area
P0327
P0332
Output voltage of the knock sensor is below 0.5 V (1 trip detection logic).
·

Short in knock sensor circuit

·

Knock sensor

·

ECM


P0328
P0333
Output voltage of the knock sensor is higher than 4.5 V (1 trip detection logic).
·

Open in knock sensor circuit

·

Knock sensor

·

ECM



HINT:

When DTC P0327, P0328, P0332 or P0333 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


Reference: Inspection using an oscilloscope

A385402E01
0.656,0.052 2.125,0.271 1.469,0.219 10 false KNK1 Signal Waveform 2.51,0.156 3.125,0.354 0.615,0.198 10 false 1 V/DIV. 2.625,0.99 3.24,1.188 0.615,0.198 10 false GND 1.021,1.875 1.938,2.104 0.917,0.229 10 false 1 msec./DIV.

The correct waveform is as shown.

Item Content
Terminal KNK1 - EKNK
KNK2 - EKN2
Equipment Setting 1 V/DIV.
0.01 to 1 msec./DIV.
Condition Engine speed at 4000 rpm with warm engine

MONITOR DESCRIPTION

If the output voltage transmitted by the knock sensor remains low or high for more than 1 second, the ECM interprets this as a malfunction in the sensor circuit and stores a DTC.

The monitor for DTCs P0327, P0328, P0332 and P0333 begins to run 5 seconds after the engine is started.

If the malfunction is not repaired successfully, DTC P0327, P0328, P0332 or P0333 is stored 5 seconds after the engine is next started.

WIRING DIAGRAM

A247758E03
0.479,1.677 0.708,1.875 0.229,0.198 10 false U2 0.479,1.865 2.25,2.063 1.771,0.198 10 false Knock Sensor (for Bank 1) 0.708,1.188 0.896,1.417 0.188,0.229 10 false 1 1.875,1.188 2.063,1.417 0.188,0.229 10 false 2 0.479,4.063 0.708,4.26 0.229,0.198 10 false U1 0.479,4.25 2.271,4.448 1.792,0.198 10 false Knock Sensor (for Bank 2) 0.719,3.594 0.906,3.823 0.188,0.229 10 false 1 1.875,3.583 2.063,3.813 0.188,0.229 10 false 2 2.26,2.552 2.854,2.75 0.594,0.198 10 false Shielded 2.26,4.938 2.854,5.135 0.594,0.198 10 false Shielded 3.417,1.115 3.594,1.292 0.177,0.177 10 false 2 3.323,1.292 3.646,1.458 0.323,0.167 10 false CU1 3.323,2.104 3.646,2.271 0.323,0.167 10 false CU1 3.323,2.885 3.646,3.052 0.323,0.167 10 false CU1 3.323,3.677 3.646,3.844 0.323,0.167 10 false CU1 3.323,4.479 3.646,4.646 0.323,0.167 10 false CU1 3.417,1.917 3.594,2.094 0.177,0.177 10 false 5 3.417,2.719 3.594,2.896 0.177,0.177 10 false 1 3.417,3.5 3.594,3.677 0.177,0.177 10 false 4 3.417,4.292 3.594,4.469 0.177,0.177 10 false 6 4.615,2.552 5.219,2.719 0.604,0.167 10 false Shielded 4.615,4.948 5.219,5.115 0.604,0.167 10 false Shielded 5.865,1.208 6.26,1.375 0.396,0.167 10 false KNK1 5.594,1.208 5.802,1.375 0.208,0.167 10 false 94 5.865,2 6.26,2.167 0.396,0.167 10 false EKNK 5.583,2 5.771,2.167 0.188,0.167 10 false 93 5.865,3.604 6.26,3.771 0.396,0.167 10 false KNK2 5.521,3.604 5.771,3.771 0.25,0.167 10 false 117 5.865,4.396 6.26,4.563 0.396,0.167 10 false EKN2 5.521,4.396 5.771,4.563 0.25,0.167 10 false 116 6.146,5.344 7.021,5.49 0.875,0.146 10 false C45 6.115,5.49 6.51,5.656 0.396,0.167 10 false ECM

CAUTION / NOTICE / HINT

HINT:
·

DTCs P0327 and P0328 are for the bank 1 knock sensor circuit.

·

DTCs P0332 and P0333 are for the bank 2 knock sensor circuit.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK KNOCK SENSOR
A413574C01
1.094,0.75 1.552,1.031 0.458,0.281 1.031,2.063 0.344,2.844 true 1.052,2.146 1.063,2.823 true 1.125,2.052 2.448,2.563 true 1.125,2.135 1.781,2.771 true 0.115,2.917 0.844,3.125 0.729,0.208 10 false 93 (EKNK) 0.823,2.854 2.198,3.052 1.375,0.198 10 false 116 (EKN2) 1.604,2.844 2.979,3.042 1.375,0.198 10 false 117 (KNK2) 2.281,2.594 3.031,2.792 0.75,0.198 10 false 94 (KNK1) 0.26,0.146 0.573,0.344 0.313,0.198 10 false *a 1.177,0.813 1.635,1.01 0.458,0.198 10 false C45
*a Front view of wire harness connector
(to ECM)


a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C45-94 (KNK1) - C45-93 (EKNK) 20°C (68°F) 120 to 280 kΩ
C45-117 (KNK2) - C45-116 (EKN2) 20°C (68°F) 120 to 280 kΩ




OK

2.CHECK TERMINAL VOLTAGE (ECM)

NG

3.CHECK HARNESS AND CONNECTOR (KNOCK SENSOR - ECM)
2.CHECK TERMINAL VOLTAGE (ECM)
U162822E02
0.469,1.135 0.781,1.313 0.313,0.177 10 false CU1 0.229,0.104 0.406,0.313 0.177,0.208 10 false *a 0.896,1.125 1.073,1.323 0.177,0.198 10 false *1

a.

Disconnect the CU1 connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
CU1 female connector 2 - 5 Ignition switch ON 4.5 to 5.5 V
CU1 female connector 4 - 6 Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*1 Female
*a Front view of wire harness connector
(to ECM Wire)



OK

NG

3.CHECK HARNESS AND CONNECTOR (KNOCK SENSOR - ECM)
a.

Disconnect the knock sensor connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U2-2 - C45-94 (KNK1) Always Below 1 Ω
U2-1 - C45-93 (EKNK) Always Below 1 Ω
U1-2 - C45-117 (KNK2) Always Below 1 Ω
U1-1 - C45-116 (EKN2) Always Below 1 Ω
U2-2 or C45-94 (KNK1) - Body ground Always 10 kΩ or higher
U2-1 or C45-93 (EKNK) - Body ground Always 10 kΩ or higher
U1-2 or C45-117 (KNK2) - Body ground Always 10 kΩ or higher
U1-1 or C45-116 (EKN2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR