Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0550  Power Steering Pressure Sensor Circuit Malfunction  P0552  Power Steering Pressure Sensor Circuit Low Input  P0553  Power Steering Pressure Sensor Circuit High Input  


DESCRIPTION

The power steering oil pressure sensor is turned on when a power steering wheel load is generated by turning the steering wheel. The ECM regulates the engine idling speed according to the voltage output of the sensor.

DTC No. DTC Detection Condition Trouble Area
P0550 Power steering oil pressure sensor voltage is below 0.28 V, or higher than 4.9 V for 0.5 seconds while the engine is running (1 trip detection logic).
·

Open or short in power steering oil pressure sensor circuit

·

Power steering oil pressure sensor

·

ECM


P0552 Power steering oil pressure sensor voltage is below 0.28 V for 0.5 seconds while the engine is running (1 trip detection logic).
·

Open or short in power steering oil pressure sensor circuit

·

Power steering oil pressure sensor

·

ECM


P0553 Power steering oil pressure sensor voltage is higher than 4.9 V for 0.5 seconds while the engine is running (1 trip detection logic).
·

Open or short in power steering oil pressure sensor circuit

·

Power steering oil pressure sensor

·

ECM



MONITOR DESCRIPTION

The ECM monitors the power steering oil pressure sensor voltage and uses this value to regulate the engine idling speed. When the power steering oil pressure sensor output voltage deviates from the normal operating range, the ECM determines that there is a malfunction in the power steering oil pressure sensor and stores a DTC.

WIRING DIAGRAM

for Manual Transmission Models
A162851E22
5.042,0.573 5.354,0.74 0.313,0.167 10 false PSP 5.302,2.979 6.208,3.146 0.906,0.167 10 false C45 5.031,1.479 5.438,1.646 0.406,0.167 10 false VCV2 1.906,0.573 2.219,0.74 0.313,0.167 10 false PSP 1.99,1.479 2.219,1.646 0.229,0.167 10 false VC 5.042,2.396 5.5,2.552 0.458,0.156 10 false ETHW 5.302,3.135 5.667,3.313 0.365,0.177 10 false ECM 4.781,0.479 4.969,0.635 0.188,0.156 10 false 72 4.781,1.375 4.969,1.531 0.188,0.156 10 false 66 4.781,2.302 4.969,2.458 0.188,0.156 10 false 97 2.323,0.469 2.448,0.625 0.125,0.156 10 false 2 2.302,1.396 2.417,1.552 0.115,0.156 10 false 1 2.302,2.302 2.417,2.458 0.115,0.156 10 false 3 2,2.396 2.208,2.542 0.208,0.146 10 false E2 0.5,2.958 0.802,3.125 0.302,0.167 10 false C59 0.5,3.125 2.792,3.292 2.292,0.167 10 false Power Steering Oil Pressure Sensor


for Automatic Transmission Models
A162851E23
5.042,0.573 5.354,0.74 0.313,0.167 10 false PSP 5.302,2.979 6.208,3.146 0.906,0.167 10 false C45 5.031,1.479 5.438,1.646 0.406,0.167 10 false VCAI 1.906,0.573 2.219,0.74 0.313,0.167 10 false PSP 1.99,1.479 2.219,1.646 0.229,0.167 10 false VC 5.042,2.396 5.5,2.552 0.458,0.156 10 false ETHW 5.302,3.135 5.667,3.313 0.365,0.177 10 false ECM 4.781,0.479 4.969,0.635 0.188,0.156 10 false 76 4.74,1.375 4.969,1.563 0.229,0.188 10 false 75 4.698,2.302 4.969,2.5 0.271,0.198 10 false 123 2.323,0.469 2.448,0.625 0.125,0.156 10 false 2 2.302,1.396 2.417,1.552 0.115,0.156 10 false 1 2.302,2.302 2.417,2.458 0.115,0.156 10 false 3 2,2.396 2.208,2.542 0.208,0.146 10 false E2 0.5,2.958 0.802,3.125 0.302,0.167 10 false C59 0.5,3.125 2.792,3.292 2.292,0.167 10 false Power Steering Oil Pressure Sensor


CAUTION / NOTICE / HINT

HINT:
·

If DTCs relating to different systems which share terminal E2 as their ground are stored simultaneously, there may be an open circuit between terminal E2 and ground.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING OIL PRESSURE SENSOR)
a.

Disconnect the ECM connector.


b.

Disconnect the power steering oil pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Manual Transmission Models
Tester Connection Condition Specified Condition
C59-2 (PSP) - C45-72 (PSP) Always Below 1 Ω
C59-1 (VC) - C45-66 (VCV2) Always Below 1 Ω
C59-3 (E2) - C45-97 (ETHW) Always Below 1 Ω
C59-2 (PSP) or C45-72 (PSP) - Body ground Always 10 kΩ or higher
C59-1 (VC) or C45-66 (VCV2) - Body ground Always 10 kΩ or higher

for Automatic Transmission Models
Tester Connection Condition Specified Condition
C59-2 (PSP) - C45-76 (PSP) Always Below 1 Ω
C59-1 (VC) - C45-75 (VCAI) Always Below 1 Ω
C59-3 (E2) - C45-123 (ETHW) Always Below 1 Ω
C59-2 (PSP) or C45-76 (PSP) - Body ground Always 10 kΩ or higher
C59-1 (VC) or C45-75 (VCAI) - Body ground Always 10 kΩ or higher




OK

2.REPLACE POWER STEERING OIL PRESSURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE POWER STEERING OIL PRESSURE SENSOR
a.

Replace the power steering oil pressure sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>POWER STEERING OIL PRESSURE SWITCH>REMOVAL).



NEXT

3.CONFIRM WHETHER DTC OUTPUT RECURS
3.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine.


e.

Idle the engine for 5 seconds.


f.

Read the DTCs.

Result
Result Proceed to
P0550, P0552 and/or P0553 is output A
No DTC is output B



A

B

END