Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2237  Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)  P2238  Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)  P2239  Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)  P2240  Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1)  P2241  Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1)  P2242  Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1)  P2252  Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)  P2253  Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)  P2255  Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1)  P2256  Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1)  


DESCRIPTION

Refer to DTC P2195 (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P2195).

DTC No. DTC Detection Condition Trouble Area
P2237
P2240
Open in the circuit between terminals AF+ and AF- of the air fuel ratio sensor while the engine is running (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


P2238
P2241
·

Case 1:


Condition (a) or (b) is met for 5.0 seconds or more (2 trip detection logic):
(a) AF+ voltage is 0.5 V or less.
(b) (AF+) - (AF-) is 0.1 V or less.
·

Case 2:


Air fuel ratio sensor admittance is below 0.0074 1/Ω (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


P2239
P2242
AF+ voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


P2252
P2255
AF- voltage is 0.5 V or less for 5.0 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


P2253
P2256
AF- voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM



HINT:
·

DTCs P2237, P2238, P2239, P2252 and P2253 indicate malfunctions related to the bank 1 air fuel ratio sensor circuit.

·

DTCs P2240, P2241, P2242, P2255 and P2256 indicate malfunctions related to the bank 2 air fuel ratio sensor circuit.

·

Bank 1 refers to the bank that includes cylinder No. 1.

·

Bank 2 refers to the bank that includes cylinder No. 2.



MONITOR DESCRIPTION

The air fuel ratio sensor varies its output voltage in proportion to the air-fuel ratio. If the air fuel ratio sensor impedance (alternating current resistance) or output voltage deviates greatly from the standard range, the ECM determines that there is an open or short in the air fuel ratio sensor circuit.

CONFIRMATION DRIVING PATTERN

1.

Start the engine and wait for 5 minutes or more.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Manual Transmission Models
Tester Connection Condition Specified Condition
C22-1 (HA1A) - C45-22 (HA1A) Always Below 1 Ω
C22-3 (A1A+) - C45-126 (A1A+) Always Below 1 Ω
C22-4 (A1A-) - C45-125 (A1A-) Always Below 1 Ω
C23-1 (HA2A) - C45-20 (HA2A) Always Below 1 Ω
C23-3 (A2A+) - C45-103 (A2A+) Always Below 1 Ω
C23-4 (A2A-) - C45-102 (A2A-) Always Below 1 Ω
C22-1 (HA1A) or C45-22 (HA1A) - Body ground Always 10 kΩ or higher
C22-3 (A1A+) or C45-126 (A1A+) - Body ground Always 10 kΩ or higher
C22-4 (A1A-) or C45-125 (A1A-) - Body ground Always 10 kΩ or higher
C23-1 (HA2A) or C45-20 (HA2A) - Body ground Always 10 kΩ or higher
C23-3 (A2A+) or C45-103 (A2A+) - Body ground Always 10 kΩ or higher
C23-4 (A2A-) or C45-102 (A2A-) - Body ground Always 10 kΩ or higher

for Automatic Transmission Models
Tester Connection Condition Specified Condition
C22-1 (HA1A) - C45-22 (HA1A) Always Below 1 Ω
C22-3 (A1A+) - C45-98 (A1A+) Always Below 1 Ω
C22-4 (A1A-) - C45-97 (A1A-) Always Below 1 Ω
C23-1 (HA2A) - C45-45 (HA2A) Always Below 1 Ω
C23-3 (A2A+) - C45-121 (A2A+) Always Below 1 Ω
C23-4 (A2A-) - C45-120 (A2A-) Always Below 1 Ω
C22-1 (HA1A) or C45-22 (HA1A) - Body ground Always 10 kΩ or higher
C22-3 (A1A+) or C45-98 (A1A+) - Body ground Always 10 kΩ or higher
C22-4 (A1A-) or C45-97 (A1A-) - Body ground Always 10 kΩ or higher
C23-1 (HA2A) or C45-45 (HA2A) - Body ground Always 10 kΩ or higher
C23-3 (A2A+) or C45-121 (A2A+) - Body ground Always 10 kΩ or higher
C23-4 (A2A-) or C45-120 (A2A-) - Body ground Always 10 kΩ or higher




OK

2.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE AIR FUEL RATIO SENSOR
a.


NEXT

3.PERFORM CONFIRMATION DRIVING PATTERN
3.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle according to Confirmation Driving Pattern.



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


d.

Read the pending DTCs.

Result
Result Proceed to
No DTC is output A
P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256 is output B



A

END

B