Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH › from 2017.08
RM2660E _59 Vehicle Exterior _052853 MIRROR (EXT) _0255764 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Automatic Retractable Mirror)

B495614C01
0.594,0.625 1.24,0.854 true 2.271,1.948 2.74,2.135 true 2.729,3.708 3.167,3.938 true 2.542,3.75 2.792,4.104 true 2.323,3.76 2.438,4.156 true 2.115,3.76 2.104,4.156 true 1.906,3.74 1.719,4.135 true 1.708,3.781 1.427,4.146 true 1.531,3.76 1.229,4.135 true 0.927,3.75 0.729,4.146 true 0.688,3.708 0.375,4.125 true 0.365,0.51 0.677,0.667 0.313,0.156 10 false *a 2.729,2.177 3.042,2.333 0.313,0.156 10 false *b 0.229,2.917 0.542,3.073 0.313,0.156 10 false *c 3.115,3.958 3.427,4.156 0.313,0.198 10 false M+ 2.292,4.177 2.708,4.458 0.417,0.281 10 false MRV 2.708,4.146 3.24,4.448 0.531,0.302 10 false MRH 1.927,4.177 2.24,4.375 0.313,0.198 10 false MLV 1.552,4.156 1.906,4.385 0.354,0.229 10 false MLH 1.344,4.156 1.521,4.354 0.177,0.198 10 false B 1.125,4.156 1.302,4.354 0.177,0.198 10 false E 0.604,4.188 0.917,4.427 0.313,0.24 10 false ILL+ 0.135,4.156 0.448,4.396 0.313,0.24 10 false ILL-
*a Left/Right Adjustment Switch
*b Mirror Surface Adjustment Switch
*c Component without harness connected
(Outer Mirror Switch Assembly)


a.

Inspect the left/right adjustment switch and mirror surface adjustment switch.

i.

Select "L" on the left/right adjustment switch.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (MLV) - 11 (B)
6 (M+) - 12 (E)
UP Pressed Below 1 Ω
Not pressed 10 kΩ or higher
9 (MLV) - 12 (E)
6 (M+) - 11 (B)
DOWN Pressed Below 1 Ω
Not pressed 10 kΩ or higher
10 (MLH) - 11 (B)
6 (M+) - 12 (E)
LEFT Pressed Below 1 Ω
Not pressed 10 kΩ or higher
10 (MLH) - 12 (E)
6 (M+) - 11 (B)
RIGHT Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select "R" on the left/right adjustment switch.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (MRV) - 11 (B)
6 (M+) - 12 (E)
UP Pressed Below 1 Ω
Not pressed 10 kΩ or higher
8 (MRV) - 12 (E)
6 (M+) - 11 (B)
DOWN Pressed Below 1 Ω
Not pressed 10 kΩ or higher
7 (MRH) - 11 (B)
6 (M+) - 12 (E)
LEFT Pressed Below 1 Ω
Not pressed 10 kΩ or higher
7 (MRH) - 12 (E)
6 (M+) - 11 (B)
RIGHT Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.

Inspect the switch illumination.

Apply battery voltage between the terminals of the light, and check the operation of the light.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 15 (ILL+)
Battery negative (-) → Terminal 16 (ILL-)
Light comes on


If the result is not as specified, replace the outer mirror switch assembly.


Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Automatic Retractable Mirror)

a.
B484846C01
1.677,0.844 1.083,0.292 true 2.75,1.365 1.885,1.76 true 0.646,3.854 0.417,4.313 true 0.833,3.844 0.74,4.344 true 2.208,3.854 2.104,4.365 true 2.583,3.865 2.479,4.375 true 2.781,3.854 2.927,4.354 true 0.906,0.167 1.219,0.365 0.313,0.198 10 false *a 0.177,2.729 0.49,2.927 0.313,0.198 10 false *c 2.802,1.24 3.115,1.438 0.313,0.198 10 false *b 0.281,4.344 0.594,4.563 0.313,0.219 10 false ILL- 0.646,4.375 0.958,4.594 0.313,0.219 10 false ILL+ 1.99,4.396 2.24,4.625 0.25,0.229 10 false M+ 2.417,4.417 2.667,4.646 0.25,0.229 10 false E 2.771,4.406 3.219,4.615 0.448,0.208 10 false MSW
*a Left/Right Adjustment Switch
*b Mirror Surface Adjustment Switch
*c Component without harness connected
(Outer Mirror Switch Assembly)


Inspect the left/right adjustment switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the outer mirror switch assembly.

13 (MSW) - 14 (E) R Below 10 Ω
OFF 10 kΩ or higher
L 90 to 110 Ω




b.

Inspect the mirror surface adjustment switch.

i.

Select "L" on the left/right adjustment switch.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the outer mirror switch assembly.

16 (M+) - 14 (E) UP Pressed 90 to 110 Ω
Not pressed 10 kΩ or higher
DOWN Pressed 437 to 503 Ω
Not pressed 10 kΩ or higher
LEFT Pressed 744 to 856 Ω
Not pressed 10 kΩ or higher
RIGHT Pressed 225 to 275 Ω
Not pressed 10 kΩ or higher



iii.

Select "R" on the left/right adjustment switch.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the outer mirror switch assembly.

16 (M+) - 14 (E) UP Pressed 90 to 110 Ω
Not pressed 10 kΩ or higher
DOWN Pressed 437 to 503 Ω
Not pressed 10 kΩ or higher
LEFT Pressed 744 to 856 Ω
Not pressed 10 kΩ or higher
RIGHT Pressed 225 to 275 Ω
Not pressed 10 kΩ or higher




c.

Inspect the switch illumination.

Apply battery voltage to the connector and check the light illumination condition.

OK:
Battery Connection Specified Condition

If the result is not as specified, replace the outer mirror switch assembly.

Battery positive (+) → Terminal 23 (ILL+)
Battery negative (-) → Terminal 24 (ILL-)
Illuminates



Hide 84873A 3.INSPECT RETRACTABLE OUTER MIRROR SWITCH (w/ Automatic Retractable Mirror)

a.
E374129C02
0.885,1.323 1.427,1.323 true 2.021,0.51 2.563,0.51 true 2,2.396 2.229,1.885 2.229,1.885 2.531,1.885 true 1.594,2.417 1.417,1.771 1.417,1.771 1.146,1.771 true 1.813,2.385 2.01,1.656 2.01,1.656 2.302,1.656 true 1.469,2.406 1.417,2.229 1.417,2.229 0.833,2.229 true 2.208,2.417 2.75,2.417 true 0.167,1.698 0.479,1.854 0.313,0.156 10 false *c 2.604,0.417 2.917,0.573 0.313,0.156 10 false *b 0.688,1.25 1,1.406 0.313,0.156 10 false *a 2.604,1.813 2.917,2.01 0.313,0.198 10 false MR 1.021,1.688 1.229,1.875 0.208,0.188 10 false E 2.365,1.583 2.677,1.781 0.313,0.198 10 false MAT 0.521,2.146 0.948,2.323 0.427,0.177 10 false ILL+ 2.813,2.344 3.156,2.542 0.344,0.198 10 false ILL-
*a Retract Switch
*b Return Switch
*c Component without harness connected
(Retractable outer mirror switch)


Inspect the retractable outer mirror switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the retractable outer mirror switch.

2 (MR) - 4 (E) Retract Below 1 Ω
Return 10 kΩ or higher
3 (MAT) - 4 (E) AUTO Below 1 Ω
Return 10 kΩ or higher




b.

Inspect the switch illumination.

Apply battery voltage to the connector and check the light illumination condition.

OK:
Battery Connection Specified Condition

If the result is not as specified, replace the retractable outer mirror switch.

Battery positive (+) → Terminal 5 (ILL+)
Battery negative (-) → Terminal 1 (ILL-)
Illuminates