Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › from 2017.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255573 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  Immobiliser System does not Operate Properly  


DESCRIPTION

The engine immobiliser system compares the ID code that is registered in the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The engine immobiliser system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the engine immobiliser system after confirming that the communication systems are functioning properly (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before replacing the ECM, ID code box (immobiliser code ECU) or certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTCs are not output (for SFI system) A
DTCs are not output (for ECD system) B
DTCs are output C



A

2.READ VALUE USING GTS (IMMOBILISER FUEL CUT STATUS)

B

3.CHECK WHETHER ENGINE STARTS

C

2.READ VALUE USING GTS (IMMOBILISER FUEL CUT STATUS)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List.


e.

Read the Data List according to the display on the GTS.

Engine
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status Status of immobiliser fuel cut / ON or OFF - -

OK:

The item in the Data List indicates "OFF".

Result Proceed to
OK (for 3UR-FE (w/ Secondary Air Injection System)) A
OK (for 3UR-FE (w/o Secondary Air Injection System)) B
OK (for 1UR-FE) C
OK (for 1GR-FE) D
NG E




A

B

C

D

E

3.CHECK WHETHER ENGINE STARTS
3.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts 5 seconds after the engine switch turned on (IG).

OK:

Engine starts normally.




OK

NG

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] - ECM)
4.CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] - ECM)
a.

Disconnect the E124 ID code box (immobiliser code ECU) connector.


b.

Disconnect the A38*1 or A52*2 ECM connector.

·

*1: for LHD

·

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 3UR-FE, 1GR-FE with Manual Transmission:
Tester Connection Condition Specified Condition
E124-4 (EFIO) - A38-46 (IMI) Always Below 1 Ω
E124-3 (EFII) - A38-48 (IMO) Always Below 1 Ω
E124-4 (EFIO) or A38-46 (IMI) - Body ground Always 10 kΩ or higher
E124-3 (EFII) or A38-48 (IMO) - Body ground Always 10 kΩ or higher

for 1UR-FE (for LHD), 1GR-FE with Automatic Transmission:
Tester Connection Condition Specified Condition
E124-4 (EFIO) - A38-40 (IMI) Always Below 1 Ω
E124-3 (EFII) - A38-29 (IMO) Always Below 1 Ω
E124-4 (EFIO) or A38-40 (IMI) - Body ground Always 10 kΩ or higher
E124-3 (EFII) or A38-29 (IMO) - Body ground Always 10 kΩ or higher

for 1UR-FE (for RHD):
Tester Connection Condition Specified Condition
E124-4 (EFIO) - A52-40 (IMI) Always Below 1 Ω
E124-3 (EFII) - A52-29 (IMO) Always Below 1 Ω
E124-4 (EFIO) or A52-40 (IMI) - Body ground Always 10 kΩ or higher
E124-3 (EFII) or A52-29 (IMO) - Body ground Always 10 kΩ or higher

for 1VD-FTV (for LHD):
Tester Connection Condition Specified Condition
E124-4 (EFIO) - A38-11 (IMI) Always Below 1 Ω
E124-3 (EFII) - A38-10 (IMO) Always Below 1 Ω
E124-4 (EFIO) or A38-11 (IMI) - Body ground Always 10 kΩ or higher
E124-3 (EFII) or A38-10 (IMO) - Body ground Always 10 kΩ or higher

for 1VD-FTV (for RHD):
Tester Connection Condition Specified Condition
E124-4 (EFIO) - A52-11 (IMI) Always Below 1 Ω
E124-3 (EFII) - A52-10 (IMO) Always Below 1 Ω
E124-4 (EFIO) or A52-11 (IMI) - Body ground Always 10 kΩ or higher
E124-3 (EFII) or A52-10 (IMO) - Body ground Always 10 kΩ or higher




OK

5.REGISTER ECU COMMUNICATION ID

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.




NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts.

OK:

Engine starts normally.




OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to Service Bulletin.




NEXT

8.REGISTER RECOGNITION CODE
8.REGISTER RECOGNITION CODE
a.

Register the recognition codes in the ECUs.

HINT:

Refer to Service Bulletin.




NEXT

9.REGISTER ECU COMMUNICATION ID
9.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.




NEXT

10.CHECK WHETHER ENGINE STARTS
10.CHECK WHETHER ENGINE STARTS

A

END (ID CODE BOX [IMMOBILISER CODE ECU] WAS DEFECTIVE)

B

GO TO SFI SYSTEM*

C

GO TO ECD SYSTEM*