Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2017.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255487 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) D

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  DTC CHECK / CLEAR  


CHECK DTC (CHECK USING GTS)


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Navigation System / Trouble Codes.


e.

Check for DTCs, and then write them down.


f.

Check the details of the DTC(s).



CLEAR DTC (CLEAR USING GTS)


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Navigation System / Trouble Codes.


e.

Clear the DTCs.



START DIAGNOSTIC MODE


HINT:
·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

·

After the engine switch is turned on (IG), check that the map is displayed before starting diagnostic mode. Otherwise, some items cannot be checked.



a.

Method 1

i.

Start the engine.


ii.
E335241E01
0.396,0.676 0.579,0.855 0.183,0.179 10 *a

While pressing and holding the "AUDIO" switch of the radio and display receiver assembly, operate the light control switch: Off → Tail → Off → Tail → Off → Tail → Off.

Text in Illustration
*a AUDIO Switch


iii.

Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.



b.

Method 2

i.

Start the engine.


ii.

Turn the radio and display receiver assembly power supply off.


iii.
E335249E01
2.819,0.622 3.011,0.819 0.192,0.196 10 *a 2.819,0.859 3.011,1.055 0.192,0.196 10 *b

Press the "SEEK" switch 5 times, and then press the "TRACK" switch 5 times within 15 seconds.

Text in Illustration
*a SEEK Switch
*b TRACK Switch


iv.

Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.




FAILURE DIAGNOSIS


a.
E278177

The "Failure Diagnosis" screen will be displayed by pressing the "Failure Diagnosis" switch on the "Service Menu" screen.



SYSTEM CHECK


a.
E382909

The "System Check Mode" screen will be displayed by selecting "System Check" on the "Failure Diagnosis" screen.



CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)


a.
E382910E01
0.323,0.552 0.552,0.552 true 1.156,1.792 1.156,0.646 true 2.135,1.792 2.135,1.563 true 2.646,1.781 2.646,1.552 true 2.938,0.958 3.115,0.958 true 0.156,0.458 0.469,0.656 0.313,0.198 10 false *a 1.094,1.792 1.406,1.99 0.313,0.198 10 false *b 2.073,1.792 2.385,1.99 0.313,0.198 10 false *c 2.583,1.802 2.896,2 0.313,0.198 10 false *d 3.156,0.875 3.417,1.073 0.26,0.198 10 false *e

System check mode screen description

Screen Description
Display Content
*a: Device Name List No. 1
·

Device Name List No. 1 displays some of the devices that make up the audio and visual system.

·

The names of the components from Device Name List No. 1 are shown in the following table.


*b: Check Result Result codes for all devices are displayed.
*c: Memory Clear
·

Present and history DTCs and registered connected device names are cleared.

·

Select "Memory CLR" for 3 seconds.


*d: Recheck
·

A system check will be performed again after the memory is cleared.

·

"Recheck" will dim during a system check.


*e: Device Name List No. 2
·

Device Name List No. 2 displays some of the devices that make up the audio and visual system.

·

The names of the components from Device Name List No. 2 are shown in the following table.



*b: Device Name List No. 1 Description
Name Component Connection Method
DA Radio and display receiver assembly -

*c: Check Result Description
Result Meaning Action
OK The device does not respond with a DTC. -
DETAIL The device responds with a DTC. Look up the DTC in "Unit Check Mode".
NCON The device was previously present, but does not respond in diagnostic mode. Check power supply wire harness of the device.
NRES The device responds in diagnostic mode, but gives no DTC information. Check power supply wire harness of the device.

*e: Device Name List No. 2 Description
Name Component Connection Method
AUX/VTR No. 1 stereo jack adapter assembly Vehicle wire harness
VTR/RR No. 1 stereo jack adapter assembly Vehicle wire harness


b.
E283642E02
1.667,0.417 1.938,0.135 1.938,0.135 2.063,0.135 true 1.365,0.615 1.24,0.115 1.24,0.115 1.104,0.115 true 0.417,0.688 0.646,0.688 true 0.385,0.938 0.615,0.938 true 2.771,0.854 3,0.854 true 2.646,1.719 2.646,1.865 true 2.115,0.063 2.427,0.26 0.313,0.198 10 false *a 0.958,0.021 1.271,0.219 0.313,0.198 10 false *b 0.24,0.604 0.552,0.802 0.313,0.198 10 false *c 0.208,0.844 0.521,1.042 0.313,0.198 10 false *d 2.583,1.885 2.896,2.083 0.313,0.198 10 false *f 3.052,0.771 3.365,0.969 0.313,0.198 10 false *e

Unit check mode screen description

Screen Description
Display Content
*a: Device name Target device
*b: History DTC Diagnostic memory results and stored DTCs are displayed.
*c: Current DTC DTCs output in the service check are displayed.
*d: DTC Diagnostic Trouble Code (DTC)
*e: Timestamp The time and date of history DTCs are displayed. (The year is displayed in 2- digit format.)
*f: Diagnosis clear switch Selecting "Code CLR" for 3 seconds clears the diagnostic memory data of the target device. (Both diagnostic system check result and the displayed data are cleared.)

HINT:
·

This screen is updated once per second.

·

A maximum of 6 DTCs can be displayed for history and present DTCs.




c.
E382911

Read the system check result.

i.

If the check result is "DETAIL", select the displayed check result to view the results on the "Unit Check Mode" screen and record them.

NOTICE:

A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit Check Mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit Check Mode" screen again to see if any other DTCs are displayed.


HINT:
·

When all results are "OK", no DTCs are output.

·

When proceeding to view the results of another device, select the "Back" switch to return to the "System Check Mode" screen. Repeat the above step to view the results of other devices.






DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)


a.
E383184

Clear DTCs

i.

Select "Memory CLR" for 3 seconds.


ii.

Confirm that the check results are cleared.

HINT:
·

To clear the DTCs for a specific device, clear the DTCs using the "Unit Check Mode" screen.

·

When clearing DTCs using the "Unit Check Mode" screen, select "Code CLR" for 3 seconds.





b.
E383185

Recheck

i.

Press the "Recheck" switch.


ii.
E383186

Confirm that all diagnostic codes are "OK" when the check results are displayed. If a result other than "OK" is displayed, perform troubleshooting again.

HINT:

When the DTCs are cleared using the "Unit Check Mode" screen, select "Back" to return to the "System Check Mode" screen and perform this operation.





FINISH DIAGNOSTIC MODE


a.

There are 2 methods to end diagnostic mode. Use one of them.


b.

Turn the engine switch off.


c.

Press and hold the "SET UP" or "MENU" switch for 3 seconds.