Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2017.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255487 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends an external device sound signal to the radio and display receiver assembly through this circuit.

The sound signal that has been sent is amplified by the radio and display receiver assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.

WIRING DIAGRAM

E335109E03
1.219,0.302 1.729,0.531 0.51,0.229 10 false VAL+ 1.208,0.76 1.719,0.99 0.51,0.229 10 false VAR+ 1.271,1.26 1.615,1.49 0.344,0.229 10 false VA- 1.156,1.771 1.667,2 0.51,0.229 10 false AGND 5.667,0.302 6.177,0.531 0.51,0.229 10 false VAL+ 5.667,0.813 6.177,1.042 0.51,0.229 10 false VAR+ 0.625,3.25 1.135,3.479 0.51,0.229 10 false t1 1.146,2.302 1.656,2.531 0.51,0.229 10 false ADPG 0.615,3.427 1.927,3.844 1.313,0.417 10 false No. 1 Stereo Jack Adapter Assembly 5.438,3.396 6.75,3.813 1.313,0.417 10 false Radio and Display Receiver Assembly 5.448,3.198 5.854,3.406 0.406,0.208 10 false F124 2.688,1.927 3.406,2.115 0.719,0.188 10 false Shielded 4.042,1.906 4.76,2.094 0.719,0.188 10 false Shielded 5.688,1.24 6.031,1.469 0.344,0.229 10 false VA- 5.667,1.76 6.177,1.99 0.51,0.229 10 false AGND 5.677,2.26 6.188,2.49 0.51,0.229 10 false ADPG 1.667,0.156 1.854,0.365 0.188,0.208 10 false 7 1.667,0.615 1.854,0.823 0.188,0.208 10 false 6 1.656,1.083 1.844,1.292 0.188,0.208 10 false 8 1.667,1.615 1.854,1.823 0.188,0.208 10 false 11 1.667,2.177 1.854,2.385 0.188,0.208 10 false 9 5.396,0.219 5.583,0.427 0.188,0.208 10 false 28 5.396,0.688 5.583,0.896 0.188,0.208 10 false 26 5.385,1.135 5.573,1.344 0.188,0.208 10 false 27 5.385,1.667 5.573,1.875 0.188,0.208 10 false 11 5.385,2.208 5.573,2.417 0.188,0.208 10 false 25

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 1 STEREO JACK ADAPTER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the t1 No. 1 stereo jack adapter assembly connector.


b.

Disconnect the F124 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
t1-7 (VAL+) - F124-28 (VAL+) Always Below 1 Ω
t1-6 (VAR+) - F124-26 (VAR+) Always Below 1 Ω
t1-8 (VA-) - F124-27 (VA-) Always Below 1 Ω
t1-11 (AGND) - F124-11 (AGND) Always Below 1 Ω
t1-9 (ADPG) - F124-25 (ADPG) Always Below 1 Ω
t1-7 (VAL+) - Body ground Always 10 kΩ or higher
t1-6 (VAR+) - Body ground Always 10 kΩ or higher
t1-8 (VA-) - Body ground Always 10 kΩ or higher
t1-11 (AGND) - Body ground Always 10 kΩ or higher
t1-9 (ADPG) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR