Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR COVER › from 2018.08
RM2660E _59 Vehicle Exterior _052853 MIRROR (EXT) _0255768 OUTER REAR VIEW MIRROR COVER A

MIRROR (EXT)  OUTER REAR VIEW MIRROR COVER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 87945B 1.INSTALL OUTER MIRROR COVER LH

a.

Install the outer mirror cover LH.

i.

Insert the rib on the outer edge of the outer mirror cover LH into the groove of the mirror body.

NOTICE:

Do not scratch the side turn signal light assembly LH.


B520223C02
2.781,2.604 3.115,2.604 false 5.958,2.656 6.292,2.656 false 0.344,0.135 0.719,0.375 0.375,0.24 12 false *A 3.542,0.167 3.917,0.406 0.375,0.24 12 false *B 3.135,2.51 3.51,2.75 0.375,0.24 10 false *a 6.281,2.563 6.656,2.802 0.375,0.24 10 false *a
*A for Type A *B for Type B
*a Rib - -



ii.

Confirm that the outer mirror cover LH and mirror body are aligned properly, and then push the outer end of the cover to attach the outer claws.

NOTICE:
·

Make sure that the upper ribs of the cover shown in part C of the illustration are properly attached to the mirror body.

·

Make sure that the ribs of the mirror body shown in part D of the illustration are not protruding from the cover.



B520224C02
0.979,0.917 1.229,0.917 false 0.917,1.417 1.167,1.417 false 4.438,0.917 4.688,0.917 false 4.365,1.417 4.615,1.417 false 2.583,1.417 2.833,1.417 false 6.031,1.417 6.281,1.417 false 0.177,0.083 0.552,0.323 0.375,0.24 12 false *A 3.469,0.052 3.844,0.292 0.375,0.24 12 false *B 0.813,0.813 1.125,1.01 0.313,0.198 10 false *a 0.75,1.323 1.063,1.521 0.313,0.198 10 false *a 4.25,0.833 4.563,1.031 0.313,0.198 10 false *a 4.188,1.333 4.438,1.5 0.25,0.167 10 true *a 2.417,1.323 2.729,1.521 0.313,0.198 10 false *a 5.875,1.323 6.188,1.521 0.313,0.198 10 false *a 0.448,0.615 0.823,0.854 0.375,0.24 12 false *C 3.771,0.698 4.146,0.938 0.375,0.24 12 false *C 2.125,0.917 2.5,1.156 0.375,0.24 12 false *D 5.573,0.917 5.948,1.156 0.375,0.24 12 false *D
*A for Type A *B for Type B
*a Rib - -



iii.
B520225C01
0.573,0.281 0.948,0.521 0.375,0.24 12 false *A 0.75,2.458 1.125,2.698 0.375,0.24 12 false *B
*A for Type A
*B for Type B


While making sure that the rib of the outer mirror cover LH fits properly into the groove of the mirror body, squeeze the inner end of the outer mirror cover LH and the outer mirror body together to attach the inner claws.



b.
B520226C01
0.271,0.198 0.646,0.438 0.375,0.24 12 false *A 0.365,2.5 0.74,2.74 0.375,0.24 12 false *B
*A for Type A
*B for Type B


Push on the outer mirror cover LH at the locations of the 8 claws to confirm that the claws are attached properly.


c.

Check that there is no gap between the outer mirror cover LH and outer mirror body.

HINT:

If there is a gap between the outer mirror cover LH and outer mirror body, noise will occur during driving.