Home › Drivetrain › CLUTCH › CLUTCH PEDAL(for LHD) › from 2018.08
RM2660E _52 Drivetrain _052808 CLUTCH _0255310 CLUTCH PEDAL(for LHD) N

CLUTCH  CLUTCH PEDAL(for LHD)  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY

a.
C403547E01
2.135,0.906 2.563,0.135 2.563,0.135 1.99,0.135 true 1.646,1.771 1.813,2.979 true 1.823,2.979 1.479,2.979 false 2.063,4.198 1.552,4.198 false 0.052,0.063 2.156,0.417 2.104,0.354 10 true Clutch Pedal Height Adjust Point 1.677,3.542 3.063,3.74 1.385,0.198 10 false Clutch Pedal Height 0.021,2.906 1.219,3.396 1.198,0.49 10 true Push Rod Play and Clutch Pedal Free Play Adjust Point 0.938,4.125 1.646,4.344 0.708,0.219 10 false Tibia Pad

Check that the clutch pedal height is correct.

Standard Clutch Pedal Height from No. 2 dash panel inshlator:

162.7 to 172.7 mm (6.41 to 6.79 in.)



b.

Adjust the clutch pedal height.

i.

Loosen the lock nut and turn the stopper bolt or clutch switch until the height is correct. Tighten the lock nut.

Torque:
16 N*m (160 kgf*cm, 12 ft.*lbf)



c.
D031462E23
1.896,1.885 1.5,1.802 true 1.875,1.719 2.25,1.719 true 1.875,1.615 1.875,1.719 false 2.292,1.635 3.26,1.802 0.969,0.167 10 false Push Rod Play 0.052,1.677 1.5,1.896 1.448,0.219 10 false Clutch Pedal Free Play

Check that the clutch pedal free play and push rod play are correct.

HINT:

Pay close attention to the change in resistance to distinguish between clutch pedal free play and push rod play while performing the inspection.


i.

Depress the clutch pedal sub-assembly until the clutch resistance begins to be felt.

Standard Pedal Free Play:

5.0 to 15.0 mm (0.197 to 0.591 in.)



ii.

Gently depress the clutch pedal sub-assembly until the resistance begins to increase a little.

Standard Push Rod Play at Pedal Top:

1.0 to 5.0 mm (0.0394 to 0.197 in.)




d.

Adjust the clutch pedal free play and push rod play.

HINT:

The push rod play can be adjusted by changing the length of the push rod. Clutch pedal free play changes together with push rod play.


i.

Loosen the lock nut and turn the push rod until the clutch pedal free play and push rod play are correct.

NOTICE:

If pedal free play and push rod play are not within the standard range even after adjustment, inspect the related parts.



ii.

Tighten the lock nut.

Torque:
12 N*m (120 kgf*cm, 9 ft.*lbf)


iii.

After adjusting the clutch pedal free play and push rod play, check the clutch pedal height.

Standard Clutch Pedal Height from Tibia Pad:

162.7 to 172.7 mm (6.41 to 6.79 in.)




e.
CL00512E44
1.552,1.594 2.208,0.74 true 1.01,1.677 1.26,1.542 true 2.302,0.583 3.344,0.927 1.042,0.344 10 false Clutch Release Point 0,1.594 0.958,1.906 0.958,0.313 10 true Full Stroke End Position 0.969,0.74 1.948,1.083 0.979,0.344 10 true 20 mm or more

Check the clutch release point.

i.

Pull the parking brake lever and chock the wheels.


ii.

Start the engine and allow it to idle.


iii.

Without depressing the clutch pedal sub-assembly, slowly move the shift lever to R until the gears engage.


iv.

Gradually depress the clutch pedal sub-assembly and measure the stroke distance from the point that the gear noise stops (release point) up to the full stroke end position.

Standard Distance from Pedal Stroke End Position to Release Point:

20 mm (0.787 in.) or more


If the distance is not as specified, perform the following operations:

·

Check the clutch pedal height.

·

Check the push rod play and clutch pedal free play.

·

Bleed the clutch line.

·

Check the clutch cover and disc.