Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2019.08
RM2660E _53 Suspension _052817 TIRE PRESSURE MONITORING _0255402 TIRE PRESSURE WARNING SYSTEM U

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  TERMINALS OF ECU  


CHECK TIRE PRESSURE WARNING ECU AND RECEIVER


a.
C420838E01
0.177,0.75 0.563,0.958 0.385,0.208 0.167,0 0.375,0.188 0.208,0.188 10 false *a 0.25,0.771 0.542,0.927 0.292,0.156 10 false L65

Disconnect the L65 tire pressure warning ECU and receiver connector and measure the voltage and resistance on the wire harness side.

Text in Illustration
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L65-1 (IG) - L65-12 (GND) B - BR IG power source Ignition switch ON 10 to 16 V
L65-7 (+B) - L65-12 (GND) R - BR Power supply (from battery) Always 10 to 16 V
L65-9 (CANH) - L65-10 (CANL) R - W CAN communication line Ignition switch off 54 to 69 Ω
L65-12 (GND) - Body ground BR - Body ground Ground Always Below 1 Ω


b.

Connect the L65 tire pressure warning ECU and receiver connector.


c.

Measure the voltage and resistance according to the value(s) in the table below. If the result is not as specified, the ECU may be malfunctioning.

HINT:

Measure the values on the wire harness side while the connector is connected.


C420839E01
4.646,0.646 5.063,0.896 0.417,0.25 4.729,0.688 5.021,0.844 0.292,0.156 10 false L65 1.458,0.156 1.708,0.313 0.25,0.156 10 false *a

Text in Illustration
*a Component with harness connected
(Tire Pressure Warning ECU and Receiver)
- -

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L65-3 (CLSW) - L65-12 (GND) W - BR Tire pressure warning reset switch
·

Ignition switch ON

·

Tire pressure warning reset switch on


Below 1.5 V
·

Ignition switch ON

·

Tire pressure warning reset switch off


8 to 15 V
L65-4 (RDA) - L65-12 (GND) G - BR Output signals Ignition switch ON Pulse generation (see waveform 1)
L65-5 (PRG) - L65-12 (GND) L - BR Input signals Ignition switch ON Pulse generation (see waveform 1)


d.
C240058E01
2.87,1.132 3.114,1.339 0.244,0.207 10 *b 0.103,0 0.310,0.216 0.207,0.216 10 *a

Using an oscilloscope, check waveform 1.

Text in Illustration
*a Example
*b GND

Waveform 1:
Item Contents
Terminal L65-4 (RDA) - L65-12 (GND)
L65-5 (PRG) - L65-12 (GND)
Tool setting 5 V/DIV, 50 μs./DIV.
Vehicle condition Ignition switch ON

HINT:

The waveform shown in the illustration is an example. If the tester displays a waveform that alternates between high and low, where high is a voltage that is between the IG power source voltage and a voltage 2.2 V lower than the IG power source voltage, and where low is a voltage of between 0 and 1.2 V, the ECU can be judged normal.