DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Start the engine.
Turn the GTS on.
Enter the following menus: Engine and ECT / Data List.
To display the list box, press the pull down menu button next to "Primary". Then select a measurement group.
When you select a measurement group, the ECU data belonging to that group is displayed.
Measurement Group List / Description
All Data / All data
Primary / -
Diesel General / General diesel data
Common Rail / Diesel common rail system related data
Common Rail (All) / Diesel common rail system related data (All data)
Diesel EGR / Diesel EGR system related data
Diesel Throttle / Diesel throttle system related data
VN Turbo / VN turbo related data
Diesel Exhaust / After treatment control system related data
Diesel Starting / "Difficult to start" related data
Diesel Rough / "Rough idle" related data
Diesel Lack of Power / "Lack of power" related data
Diesel Knocking / "Knocking" related data
Diesel Black Smoke / "Black smoke" related data
Compression / Data used during "Check the Cylinder Compression" Active Test
A/T / Automatic transaxle system related data
Vehicle Information / Vehicle information
Check the values by referring to the table below.
Normal Condition: If no idling conditions are specified, the shift lever should be in the neutral position, the A/C switch and all accessory switches should be off, and PM forced regeneration should not be being performed.
Engine Control
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Calculate Load | Load calculated by ECM/
Min.: 0%, Max.: 100% |
·
Idling: 15.4 to 20.4% ·
Running without load (2500 rpm): 20.1 to 25.9% ·
Driving with the accelerator fully open at 3000 rpm: 80.3 to 99.6% ·
Driving with the accelerator fully open at 4000 rpm: 96.4 to 98% |
Calculated by ECM | Malfunction in which turbo pressure or Mass Air Flow decreases |
| Diagnostic Note:
Calculated load = (Final injection volume / max. injection volume at current engine speed) x 100. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| MAF | Airflow rate from mass air flow meter/
Min.: 0 gm/sec, Max.: 400 gm/sec |
w/ EGR (depending on EGR rate)
·
Idling: 5 to 12 gm/sec. ·
Running without load (2000 rpm): 28.2 to 130 gm/sec. w/o EGR (depending on EGR rate)
·
Idling: 20 to 28 gm/sec. ·
Running without load (2000 rpm): 90 to 130 gm/sec.
|
Sensor output (mass air flow meter) | ·
Mass air flow meter ·
Mass air flow meter circuit ·
Intake related clog or leak ·
Exhaust related clog ·
Turbocharger sub-assembly ·
Leak or clog in passages for turbocharger ·
Malfunction in which EGR valve does not close |
| Symptoms when out of range:
Rough idling |
||||
| Diagnostic Note:
·
Based on the MAF, the ECM controls the fuel injection volume, injection timing, EGR, etc. ·
If the value is always approximately 0 gm/sec: -
Mass air flow meter power source circuit is open. -
VG circuit is open or shorted. -
EVG circuit is open. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Engine Speed | Engine speed/
Min.: 0 rpm, Max.: 6000 rpm |
·
Idling: 550 to 650 rpm (A/T) ·
Idling: 500 to 600 rpm (M/T) |
Sensor output (crankshaft position sensor) | ·
Crankshaft position sensor ·
Crankshaft position sensor circuit |
| Diagnostic Note:
When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Target Idle Engine Speed | Target Idling Engine Speed/
Min.: 0 rpm, Max.: 10000 rpm |
- | Target idling speed (ECM calculated value) | - |
| Diagnostic Note:
·
Target engine speed for idling speed control. ·
The ECM calculates the target engine idling speed while considering the air conditioner load, electric load, shift position changes, idle-up control for cold engine start, etc. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| MAP | Absolute pressure inside intake manifold/
Min.: 0 kPa, Max.: 320 kPa |
·
Idling: 90 to 102 kPa (depending on barometric pressure)
·
Engine running at 3000 rpm: 100 to 150 kPa |
Sensor output (manifold absolute pressure sensor) | ·
Manifold absolute pressure sensor ·
Intake related clog or leak ·
Exhaust related clog ·
Turbocharger sub-assembly ·
Leak or clog in passages for turbocharger ·
EGR valve stuck open ·
Exhaust leak ·
Throttle valve stuck closed |
| Symptoms when out of range:
Lack of power |
||||
| Diagnostic Note:
·
When the ignition switch is ON or the vehicle is idling, the intake manifold absolute pressure and atmospheric pressure are approximately the same (standard atmospheric pressure = 101 kPa). Above approximately 1500 rpm, the turbo becomes effective and the pressure becomes higher than atmospheric pressure. ·
Inspect while comparing with "Target Booster Pressure". ·
With the accelerator fully open, if the actual manifold absolute pressure (MAP) is low compared to the target booster pressure by at least 20 kPa for 5 seconds or more, a feeling of insufficient power will occur. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed/
Min.: 0 km/h, Max.: 255 km/h |
Actual vehicle speed | Sensor output (speed sensor) | ·
Speed sensor ·
Speed sensor circuit |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Coolant Temp | Engine coolant temperature/
Min.: -40°C, Max.: 140°C |
After warming up engine: 70 to 90°C (158 to 194°F) | Sensor output (engine coolant temperature sensor) | ·
Engine coolant temperature sensor ·
Thermostat |
| Symptoms when out of range:
Difficulty starting when engine is cold, rough idle, black smoke, lack of power |
||||
| Diagnostic Note:
·
If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted. ·
After a long soak, the coolant temperature, intake air temperature and ambient temperature are approximately equal. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Intake Air | Intake air temperature/
Min.: -40°C, Max.: 140°C |
Equivalent to temperature at location of mass air flow meter | Sensor output (intake air temperature sensor (built into mass air flow meter)) | Intake air temperature sensor |
| Diagnostic Note:
·
After a long soak, the engine coolant temperature, intake air temperature and ambient temperature are approximately equal. ·
If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Initial Engine Coolant Temp | Initial engine coolant temperature/
Min.: -40°C, Max.: 120°C |
Engine coolant temperature when engine started | Sensor output when engine started | - |
| Diagnostic Note:
For freeze frame data, this tells whether the malfunction happened at a cold start or with a warm engine. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Initial Intake Air Temp | Initial intake air temperature/
Min.: -40°C, Max.: 120°C |
Intake air temperature when engine started | Sensor output when engine started | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Intake Air Temp (Turbo) | Intake air temperature after intercooler/
Min.: -40°C, Max.: 190°C |
70°C (158°F) or less | Sensor output (intake air temperature sensor after intercooler) | Decreased cooling efficiency of intercooler (contamination, clogging) |
| Diagnostic Note:
·
This is the intake air temperature at the intake manifold (after the intercooler). ·
During fail-safe operation, the value is set to 165°C (329°F). As the value is set to a high temperature, the turbo pressure may be suppressed and there may be a lack of power. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Alternate Duty Ratio | Alternator generation duty ratio/
Min.: 0%, Max.: 100% |
·
No electrical load at idling: 10 to 60% ·
High electrical load at idling: 100% |
Duty value from ALT terminal | ·
Battery deterioration ·
Alternator malfunction ·
Electric load, lights, etc. |
| Diagnostic Note:
·
This outputs the alternator generation duty and is used to determine the electrical load. ·
Can be used to determine whether a higher-than-normal injection volume at idle, etc. is due to electrical loading or from some other source. For example, when the duty is not high but the idling injection volume is high, there is injector volume degradation or high engine friction. ·
Can be used for judging whether or not a malfunctioning component in the electrical system is generating continual generation requests (e.g., battery deterioration is causing an unending full recharge request, etc.). Regardless of whether or not an auxiliary device like the A/C or heater is active, if the alternator duty is always at the maximum value, there is an electrical system abnormality, like battery deterioration. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Viscous Heater Stop Request | Viscous heater stop request/
ON or OFF |
ON: Viscous heater stop requested | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| A/C Signal | A/C (Air Conditioner) signal/
ON or OFF |
ON: A/C on | A/C operation signal output from A/C amplifier
·
ON: Operating ·
OFF: Not operating |
·
A/C switch ·
A/C amplifier ·
A/C system malfunction, wire harness between A/C amplifier and ECU open or shorted |
| Symptoms when out of range:
OFF malfunction (OFF even when A/C switch is turned on): ·
Engine speed decreases temporarily when the A/C is operating. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Stop Light Switch | Stop light switch/
ON or OFF |
·
ON: Brake pedal depressed ·
OFF: Brake pedal released |
Switch output (stop light switch) | ·
OFF malfunction: Wire harness (stop light switch to ECM, stop light switch to +B) open or shorted to ground ·
ON malfunction: Wire harness (stop light switch to ECM) shorted to +B ·
Stop light switch |
| Symptoms when out of range:
Stop light switch malfunction DTC P0504 is stored |
||||
| Diagnostic Note:
Stop light switch (STP) operation condition: ·
ON: Light is on (Brake pedal is depressed) ·
OFF: Light is off (Brake pedal is released) |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Battery Voltage | Battery voltage/
Min.: 0 V, Max.: 15 V |
11 to 14 V | - | - |
| Symptoms when out of range:
If 5 V or less, starting becomes difficult |
||||
| Diagnostic Note:
If 11 V or less, characteristics of some electrical components change. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Atmosphere Pressure | Atmospheric pressure value/
Min.: 50 kPa, Max.: 120 kPa |
Actual atmospheric pressure | Sensor output (atmospheric pressure sensor (built into ECM)) | Atmospheric pressure sensor itself has failed (atmospheric pressure sensor is inside the ECM) |
| Diagnostic Note:
·
With the ignition switch ON, when the difference between the atmospheric pressure sensor and intake manifold absolute pressure is 10 kPa or more, there is a malfunction in one of the sensors. ·
With the ignition switch ON, when the atmospheric pressure is 0 kPa or 140 kPa, there is a malfunction in the sensor circuit. ·
Standard atmospheric pressure: 101 kPa. ·
For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather (high atmospheric pressure, low atmospheric pressure). |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| ACT VSV | A/C cut status/
ON or OFF |
- | - | - |
| Diagnostic Note:
"Control the A/C Cut Signal" Active Test support data. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Brake Override System | Brake Override System status/
ON or OFF |
ON: Brake override system operating | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| TC and TE1 | TC and TE1 connection status/
ON or OFF |
- | - | - |
| Diagnostic Note:
When the "Connect the TC and TE1" Active Test is performed, the system behaves as if TC and CG were connected. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Total Distance Traveled | Total Distance Traveled/
Min.: 0 km (0 mile), Max.: 16777215 km (10425361 mile) |
Total distance vehicle driven after battery cable disconnected | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| # Codes (Include History) | Number of codes/
Min.: 0, Max.: 255 |
- | - | - |
| Diagnostic Note:
Number of DTCs appearing at least once during the last 40 times the vehicle was warmed up. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Check Mode | Check mode status/
ON or OFF |
ON: Check mode on | - | - |
| Diagnostic Note:
Check Mode: The mode in which certain DTCs can be detected more easily and with higher sensitivity. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| MIL | MIL status/
ON or OFF |
OFF: MIL off | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| MIL ON Run Distance | Distance traveled with MIL on/
Min.: 0 km, Max.: 65535 km |
Distance traveled after DTC stored | Result of ECU calculations (using the vehicle speed) | - |
| Diagnostic Note:
·
Distance traveled after a DTC is stored. ·
Cleared when the cable is disconnected from the negative (-) battery terminal, or when the DTC is cleared using the GTS. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Running Time from MIL ON | Running time after MIL turns on/
Min.: 0 min., Max.: 65535 min. |
Running time after MIL turns on | - | - |
| Diagnostic Note:
·
Engine run time since the MIL illumination. ·
Cleared when the cable is disconnected from the negative (-) battery terminal, or when the DTC is cleared using the GTS. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Engine Run Time | Engine run time/
Min.: 0 sec., Max.: 65535 sec. |
Time after the ignition switch ON | Result of ECU calculations (using the engine speed) | - |
| Diagnostic Note:
Time passed since the ignition switch was ON. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Time after DTC Cleared | Time after DTC cleared/
Min.: 0 min., Max.: 65535 min. |
Time after DTCs cleared | - | - |
| Diagnostic Note:
Time elapsed since the DTCs were cleared (or shipment from the factory). |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Distance from DTC Cleared | Distance driven after DTC cleared/
Min.: 0 km, Max.: 65535 km |
Distance driven after DTCs cleared | - | - |
| Diagnostic Note:
·
Distance driven since the DTCs were cleared. ·
(Data List "Distance from DTC clear") - (Freeze frame data "Distance from DTC cleared") = Distance driven since the abnormality occurred. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Warmup Cycle Cleared DTC | Warmup cycles after DTC cleared/
Min.: 0, Max.: 255 |
- | - | - |
| Diagnostic Note:
·
Number of engine warmup since DTCs were cleared. ·
(Data List "Warmup Cycle Cleared DTC") - (Freeze frame data "Warmup Cycle Cleared DTC") = Warmup cycles since the abnormality occurred. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| OBD Requirements | Identifying OBD requirement | - | - | - |
| Diagnostic Note:
Euro-OBD |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Number of Emission DTC | Number of emissions-related DTCs | - | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Power Steering Signal | Power steering switch status/
ON or OFF |
- | - | - |
| Symptoms when out of range:
This item is displayed on the GTS but is not used. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Transfer L4 | L4 status of the transfer/
ON or OFF |
ON: 4WD control switch in 4L position | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Idle Up Signal | Status of the idle up signal/
ON or OFF |
- | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| TC Terminal | TC terminal status/
ON or OFF |
- | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Dist Batt Cable Disconnect | Distance driven after battery cable disconnected/
Min.: 0 km, Max.: 65535 km |
Total distance vehicle driven after battery cable disconnected | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Minimum Engine Speed | Minimum engine speed/
Min.: 0 rpm, Max.: 51199 rpm |
- | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| ACM Inhibit | VSV for engine mount status/
ON or OFF |
- | - | - |
| Diagnostic Note:
·
VSV for engine mount status: -
Ignition switch ON: OFF. -
Idling: ON. ·
Active Test "Control the ACM Inhibit" support data. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Accel Position | Accelerator position status/
Min.: 0%, Max.: 100% |
·
Accelerator pedal released: 0% ·
Accelerator pedal fully depressed: 100% |
·
Accelerator pedal position sensor opening position ·
ECT requested opening position ·
Cruise requested opening position ·
VSC requested opening position |
- |
| Diagnostic Note:
·
"Accel Position" is the accelerator opening amount (%) for engine control use. ·
When the accelerator pedal position sensor output itself (Accelerator Position 1, Accelerator Position 2) is in the normal voltage range, another actuator malfunction has caused the fail-safe function to restrict the accelerator. ·
Without cruise, ECT or VSC requests, and without accelerator restriction by the fail-safe function, this is adjusted in proportion to the amount the accelerator pedal is depressed by the driver. ·
Accelerator pedal released: 0% ·
Accelerator pedal fully depressed: 100% |
||||
Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt % express the value obtained by dividing the output voltage from the accelerator pedal position sensor by 5. This is used only for diagnosing malfunctions in the accelerator pedal position sensor. Under normal conditions, it is sufficient to only check the final accelerator opening angle value "Accel Position".
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Accel Sens. No.1 Volt % | Accelerator position No. 1/
Min.: 0%, Max.: 100% |
·
Accelerator pedal released: 10 to 22% ·
Accelerator pedal fully depressed: 52 to 90% |
Sensor output (Accelerator pedal position sensor) | - |
| Diagnostic Note:
Read value with ignition switch ON (do not start engine). |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Accel Sens. No.2 Volt % | Accelerator position No. 2/
Min.: 0%, Max.: 100% |
·
Accelerator pedal released: 24 to 40% ·
Accelerator pedal fully depressed: 68 to 99% |
Sensor output (Accelerator pedal position sensor) | - |
| Diagnostic Note:
Read value with ignition switch ON (do not start engine). |
||||
Compression
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Engine Speed of Cyl #1
Engine Speed of Cyl #2 Engine Speed of Cyl #3 Engine Speed of Cyl #4 Engine Speed of Cyl #5 Engine Speed of Cyl #6 Engine Speed of Cyl #7 Engine Speed of Cyl #8 |
Engine speed for No. 1 to No. 8 cylinder/
Min.: 0 rpm, Max.: 51199 rpm |
Engine speeds of all cylinders almost same | - | Compression goes down |
| Symptoms when out of range:
When the engine speeds of all cylinders are not equal, idling will be rough. |
||||
| Diagnostic Note:
·
Output only when the "Check the Cylinder Compression" Active Test is performed. ·
Indicates the speed of each cylinder when cranking. Example - Normal: Engine speeds of all cylinders are approximately equal. When No. 1 cylinder compression is low, "Engine Speed of Cyl #1" is approximately 300 rpm, and "Engine Speed of Cyl #2 to #8" is approximately 200 rpm. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Av Engine Speed of All Cyl | Engine speed for all cylinders/
Min.: 0 rpm, Max.: 51199 rpm |
- | - | - |
| Diagnostic Note:
·
Output only when the Active Test "Check the Cylinder Compression" is performed. ·
Indicates the average engine speed of all cylinders during cranking. |
||||
Vehicle Information
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Model Code | Model code | - | - | - |
| Diagnostic Note:
Identifying model code: VDJ200 |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Engine Type | Engine type | - | - | - |
| Diagnostic Note:
Identifying engine type: 1VDFTV |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Cylinder Number | Cylinder number/
Min.: 0, Max.: 255 |
- | - | - |
| Diagnostic Note:
Identifying cylinder number: 8 |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Transmission Type | Transaxle type/
MT or ECT 6th |
- | - | - |
| Diagnostic Note:
Identifying transaxle type: ·
MT: Manual transmission ·
ECT 6th: Automatic transmission |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Destination | Destination | - | - | - |
| Diagnostic Note:
Identifying destination: W |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Model Year | Model year/
Min.: 1900, Max.: 2155 |
- | - | - |
| Diagnostic Note:
Identifying model year: 20## |
||||
Diesel Injection
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Injection Volume | Injection volume/
Min.: 0 mm3/st, Max.: 1279.98 mm3/st |
Idling: 3 to 10 mm3/st | Calculated value | - |
| Diagnostic Note:
·
Injection amount for each combustion. ·
If injector assemblies are clogged, fuel quality is poor, the fuel filter element sub-assembly is clogged, or engine friction increases, "Injection Volume" will increase. ·
If there is a malfunction due to low turbocharger pressure or a low intake air volume, the injection volume is limited and there is a lack of power. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Inj. FB Vol. for Idle | Idle stability status integral control volume/
Min.: -80 mm3/st, Max.: 79 mm3/st |
-10 to 10 mm3/st | - | - |
| Symptoms when out of range:
Engine friction problem, compression problem or injector breakdown |
||||
| Diagnostic Note:
·
When the actual engine speed does not match the target idling speed, this corrects the injection volume. If this item displays 10 mm3/st or more or -10 mm3/st or less even with the engine completely warmed up and the air conditioning and other electrical loads off, the internal parts of the engine may be damaged, or the fuel injection system or other auxiliary components may be malfunctioning. ·
Only calculated and reflected at idle. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Inj Vol Feedback Learning | Injection volume feedback learning value/
Min.: -10 mm3/st, Max.: 9.92 mm3/st |
- | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Injection Feedback Val #1
Injection Feedback Val #2 Injection Feedback Val #3 Injection Feedback Val #4 Injection Feedback Val #5 Injection Feedback Val #6 Injection Feedback Val #7 Injection Feedback Val #8 |
Injection volume correction for each cylinder/
Min.: -10 mm3/st, Max.: 10 mm3/st |
Idling: -3.0 to 3.0 mm3/st | Learned value | ·
Injector clogging ·
Injector deterioration ·
Decrease in cylinder compression ·
Injector compensation code is incorrectly set (forgot to input code after replacement or made mistake during setting of code after replacing ECM with one from another vehicle) |
| Symptoms when out of range:
Rough idling, black smoke, white smoke, poor driveability, lack of power, abnormal combustion noise, difficult to start |
||||
| Diagnostic Note:
·
When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder. Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased. ·
"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion. ·
Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.
|
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Pilot 1 Injection Period | Pilot 1 injection period/
Min.: 0 μs, Max.: 65535 μs |
Idling: 0 μs | Calculated value | - |
| Symptoms when out of range:
Combustion noise, poor driveability, white smoke |
||||
| Diagnostic Note:
Check to see if "Pilot 1 Injection Period" is not zero when symptoms occur. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Pilot 2 Injection Period | Pilot 2 injection period/
Min.: 0 μs, Max.: 65535 μs |
Idling: 390 to 490 μs | Calculated value | - |
| Symptoms when out of range:
Combustion noise, poor driveability, white smoke |
||||
| Diagnostic Note:
Check to see if "Pilot 2 Injection Period" is not zero when symptoms occur. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Main Injection Period | Main injection period/
Min.: 0 μs, Max.: 65535 μs |
Idling: 490 to 690 μs | Calculated value | - |
| Diagnostic Note:
·
When the fuel pressure becomes 15000 kPa or less, "Main Injection Period" is set to 0. ·
When the engine will not start, confirm that injection is performed. ·
When P0093, P0627, P062D or P062E is stored, there is an engine stall request. At that time, "Main Injection Period" equals 0.
|
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| After Injection Period | After injection period/
Min.: 0 μs, Max.: 65535 μs |
- | Calculated value | - |
| Diagnostic Note:
Check to see if "After Injection Period" is not zero when the following symptoms occur: Black smoke, poor driveability. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Pilot 1 Injection Timing | Pilot 1 injection timing/
Min.: -70 deg(CA), Max.: 20 deg(CA) |
- | Calculated value | - |
Diagnostic Note:
|
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Pilot 2 Injection Timing | Pilot 2 injection timing/
Min.: -50 deg(CA), Max.: 20 deg(CA) |
Idling after engine warmed up and vehicle under normal atmospheric pressure: 6 to 2 deg(CA) | Calculated value | - |
Diagnostic Note:
|
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Main Injection Timing | Main injection timing/
Min.: -90 deg(CA), Max.: 90 deg(CA) |
Idling after engine warmed up and vehicle under normal atmospheric pressure: 0.5 to -4 deg(CA) | Calculated value | - |
| Diagnostic Note:
Use "Main Injection Timing" to check poor drivability when the following symptoms are present: Bad injection timing, black smoke, and white smoke.
|
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| After Injection Timing | After injection timing/
Min.: -10 deg(CA), Max.: 50 deg(CA) |
- | Calculated Value | - |
Diagnostic Note:
|
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Injection Pressure Correction | Injection pressure feedback compensation volume/
Min.: -500 mm3/st, Max.: 780 mm3/st |
-20 to 20 mm3/st at standard temperature | Calculated value | ·
Suction control valve malfunction ·
Clogged fuel filter element sub-assembly |
| Diagnostic Note:
·
When the (actual) fuel pressure is equal to the target fuel pressure, this value becomes 0. ·
This indicator can be used for diagnosing supply pump related malfunctions. ·
When this value (absolute value) is large, it indicates that the difference between the actual and target fuel pressure is also large. A positive value indicates that the pressure feed is being increased due to insufficient pressure. A negative value indicates that pressure is being reduced due to excessive rail pressure. When the suction control valve does not close properly, it causes rail overpressure, and this value and the "Pump SCV Learning Value" slip to the negative volume side. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Injection EDU Relay Request
Injection EDU Relay Request #2 |
Status of the EDU relay request/
ON or OFF |
ON: EDU relay ON | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Target Common Rail Pressure | Target common rail pressure/
Min.: 0 kPa, Max.: 250000 kPa |
25000 to 180000 kPa when engine running | Target common rail pressure (ECU calculated value) | - |
| Diagnostic Note:
·
Inspect the (actual) fuel pressure, comparing it with the common rail target value. ·
Considered normal when the actual fuel pressure is within +/-5000 kPa of the target fuel pressure under stable conditions when idling after warming up the engine. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Common Rail Pressure | Actual common rail pressure/
Min.: 0 kPa, Max.: 250000 kPa |
Idling: 27000 to 37000 kPa | Sensor output (fuel pressure sensor) | ·
Fuel supply pump assembly ·
High pressure pipes ·
Fuel pressure sensor ·
Injector assembly ·
Feed pump (fuel supply pump assembly) ·
Fuel filter element sub-assembly ·
Pressure discharge valve ·
Air in the fuel pipes ·
Lack of fuel |
| Symptoms when out of range:
Difficult to start, poor driveability, lack of power, abnormal combustion noise |
||||
| Diagnostic Note:
·
Common Rail Pressure is the actual common rail fuel pressure. ·
Inspect by comparing the fuel pressure with the target fuel pressure. ·
When in a stable condition such as when idling after warming up the engine, the fuel pressure is within +/-5000 kPa of the target fuel pressure. ·
The ECM uses fuel pressure for feedback control of the target fuel pressure via the fuel supply pump assembly. The injection amount is determined based on the injection timing and fuel pressure. Also, the spray pattern is selected based on the fuel pressure. ·
For startup, at least 25000 kPa of fuel pressure is needed (take care as there is a response lag when the pressure rises). ·
When the fuel pressure is below 25000 kPa, it may cause rough idling. ·
When the fuel pressure has decreased by 20000 kPa from the target fuel pressure, there may be a lack of power. ·
If actual fuel pressure is 5000 kPa higher than the target fuel pressure, P1229 will be stored. When the actual fuel pressure is lower than the target fuel pressure, "P1608 Lack of Power" may be detected depending on the degree of deviation from the target pressure. ·
When the fuel pressure is higher than 230000 kPa, DTC P0088 will be stored. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Fuel Temperature | Fuel temperature/
Min.: -40°C, Max.: 140°C |
Actual fuel temperature | Sensor output (fuel temperature sensor) | - |
| Diagnostic Note:
After fully cold soaking the engine, the fuel temperature is the same as the outside air temperature. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Intank Fuel Pump | Intank Fuel Pump status/
ON or OFF |
Operates according to fuel consumption amount
(Operates after about 10 minutes of driving) |
Operation command | - |
| Diagnostic Note:
·
ON: Intank fuel pump is operating. ·
Only for vehicles equipped with a double tank. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Target Pump SCV Current | Final pump current target value/
Min.: 0 mA, Max.: 4000 mA |
Idling: 923 to 1123 mA | Target value control (pump current) | ·
Suction control valve malfunction ·
Clogged fuel filter element sub-assembly |
| Symptoms when out of range:
Difficulty starting, lack of power or rough idling |
||||
| Diagnostic Note:
·
ECU-calculated value for the suction control valve actuation target current. ·
Value is large when a high fuel pressure is desired. ·
Normally, the value is between 800 and 2500 mA. ·
If the value is stuck at 3000 mA or higher, it indicates that the operation is poor (poor movement due to deposits, etc.). ·
When this deviates from the standard value, it indicates that for some reason, even though the pump is running hard, the actual fuel pressure is inconsistent with the target fuel pressure. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Pump SCV Learning Value | Pump SCV learning value/
Min.: -4096 mA, Max.: 4095.8 mA |
·
Min.: -100 mA ·
Max.: 100 mA |
Learned value | ·
Suction control valve malfunction ·
Clogged fuel filter element sub-assembly |
| Symptoms when out of range:
Difficulty starting, lack of power or rough idling |
||||
| Diagnostic Note:
If the value is stuck at 200 mA or higher or -200 mA or less, it indicates that the operation is poor (poor movement due to deposits, etc.). |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Pump SCV Status | Pump SCV Status/
ON or OFF |
- | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Pump SCV Duty Request | Pump SCV duty request/
Min.: 0%, Max.: 39.9% |
- | Calculated value | - |
EGR System
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Target EGR Valve Pos,
Target EGR Valve Pos #2 |
EGR valve target opening amount/
Min.: 0%, Max.: 100% |
Idling after engine warmed up: 0 to 65% | ECU-calculated value based on sensors (mass air flow meter, manifold absolute pressure sensor, intake air temperature (built into mass air flow meter), etc.) | - |
| Symptoms when out of range:
·
When value is out of range and approaching 0%: mass air flow meter degradation, intake or exhaust system blockage ·
When value is out of range and approaching 100%: EGR pipe blockage |
||||
| Diagnostic Note:
·
Fully open: 100%. ·
Fully closed: 0%. ·
Used for comparison to "Actual EGR Valve Pos" and "Actual EGR Valve Pos #2". |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Actual EGR Valve Pos
Actual EGR Valve Pos #2 |
Actual EGR valve position/
Min.: 0%, Max.: 100% |
Idling after engine warmed up: 0 to 80% | Calculated from EGR valve position sensor | - |
| Symptoms when out of range:
·
EGR valve stuck open: Poor starts (engine does not stop), black smoke, white smoke, lack of power ·
EGR valve stuck closed: Increased turbo booster noise |
||||
| Diagnostic Note:
·
Fully open: 100%. ·
Fully closed: 0%. ·
Inspect while comparing to "Target EGR Valve Pos" and "Target EGR Valve Pos #2". ·
Check the valve movement via the Active Test. ·
Sometimes malfunctions only occur around a certain temperature, so refer to the engine coolant temperature and outside temperature at the time the malfunction occurred. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| EGR Position Sensor
EGR Position Sensor #2 |
EGR position sensor position/
Min.: 0 V, Max.: 4.99 V |
Idling after engine warmed up: 0.8 to 4.5 V | Sensor output (EGR valve position sensor) | - |
| Diagnostic Note:
·
This is the output voltage of the EGR valve position sensor. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| EGR Motor Duty #1
EGR Motor Duty #2 |
EGR valve actuation duty/
Min.: 0%, Max.: 127.5% |
Idling after engine warmed-up: 0 to 100% | - | - |
| Diagnostic Note:
·
This EGR Motor Duty #1 is calculated based on Target EGR Valve Pos. to actuate the No. 1 EGR valve assembly. ·
This EGR Motor Duty #2 is calculated based on Target EGR Valve Pos #2 to actuate the No. 2 EGR valve assembly. ·
To 0%: Close side EGR valve actuation. ·
To 100%: Open side EGR valve actuation. ·
When this value is large but the actual valve position does not reach the target valve position, there is an unable to open malfunction. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| EGR Close Lrn. Val.
EGR Close Lrn. Val. #2 |
EGR fully closed position learned value/
Min.: 0 V, Max.: 5 V |
3.5 to 4.5 V | EGR valve position sensor value when EGR valve fully closed | - |
| Diagnostic Note:
·
This value is the EGR position sensor output voltage. ·
When the value is at the upper or lower limit of the normal range, it is possible that a foreign object is lodged in the EGR valve seat area. ·
As the lower and upper limits are 3.5 V and 4.5 V respectively, if the value becomes stuck at either of these values, there is a malfunction in the lift sensor or the valve position may be misaligned (foreign matter is present, etc.). |
||||
Diesel Throttle System
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Throttle Sensor Volt %
Throttle Sensor #2 Volt % |
Absolute throttle position sensor/
Min.: 0%, Max.: 100% |
·
Ignition switch ON: 60 to 80% ·
Warmed-up and idling: 10 to 80% |
Sensor output (throttle position sensor) | - |
| Symptoms when out of range:
·
Stuck closed: Engine stall, difficult to start, rough idling, lack of power, black smoke, white smoke ·
Stuck open: Loud turbocharging sound, bad vibration when engine is stopped ·
When the ECM detects a malfunction with the diesel throttle (MIL on), engine power is restricted but city driving is possible. |
||||
| Diagnostic Note:
·
Throttle position sensor output voltage is converted using 5 V = 100%. ·
When fully closed: 14%. ·
When fully open: 70%. ·
When the ignition switch is turned from off to ON, the throttle valve fully opens once. ·
When the ignition switch is turned from ON to off, the throttle valve fully closes once. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Target Throttle Position
Target Throttle Position #2 |
Target throttle position/
Min.: -128%, Max.: 127% |
·
Throttle valve fully opened: 100% ·
Throttle valve fully closed: 0% |
Value calculated by ECM | - |
| Diagnostic Note:
If there is a malfunction of the throttle actuator, compare the target and actual throttle position values for troubleshooting.
|
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Actual Throttle Position
Actual Throttle Position #2 |
Actual diesel throttle position/
Min.: -20%, Max.: 120% |
Idling after engine warmed-up: 10 to 100% | - | - |
| Symptoms when out of range:
·
Stuck closed: Engine stall, difficult to start, lack of power, black smoke, rough idle ·
Stuck open: Loud turbocharging sound, bad vibration when engine is stopped ·
When ECM detects a malfunction of the diesel throttle (MIL on), engine power is restricted so that the vehicle can drive with a maximum speed of 80 to 100 km/h. |
||||
Diagnostic Note:
|
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Throttle Motor Duty
Throttle Motor Duty #2 |
Diesel throttle motor duty/
Min.: 0%, Max.: 100% |
- | - | - |
| Diagnostic Note:
When the moving force to open and close the diesel throttle valve increases, the value of Throttle Motor Duty increases. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Throttle Close Learning Val.
Throttle Close Learning Val #2 |
Throttle fully closed position learned value/
Min.: 0 deg, Max.: 84 deg |
14.25 to 21.25 deg | - | - |
| Diagnostic Note:
·
When the ignition switch is turned from ON to off and 5 seconds elapse, learning of "Throttle Close Learning Val." and "Throttle Close Learning Val #2" will be complete. ·
When "Throttle Close Learning Val." is outside of the normal range, a foreign object may be lodged in the throttle valve (for bank 1). ·
When "Throttle Close Learning Val #2" is outside of the normal range, a foreign object may be lodged in the throttle valve (for bank 2). ·
If the value is stuck at the upper limit of 21.25 deg, there is a chance that a malfunction is present. However, as the initial value for the learned value is 21.25 deg, it is necessary to check the value after learning is completed. |
||||
VN Turbo System
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Target Booster Pressure | Target booster pressure/
Min.: 0 kPa, Max.: 320 kPa |
Driving vehicle on level surface at 3000 rpm with full load: 200 to 225 kPa | Value calculated by ECM | - |
| Diagnostic Note:
·
Inspect while comparing with "MAP". ·
With the accelerator fully open, if the actual manifold absolute pressure (MAP) is low compared to the target booster pressure by at least 20 kPa for 5 sec. or more, a feeling of a lack of power will occur. ·
When the vehicle is driven with the engine speed at 3000 rpm or more and the accelerator pedal fully depressed, "MAP" is approximately equal to "Target Booster Pressure". |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Target VN Turbo Position
Target VN Turbo Position #2 |
Target VN turbo position/
Min.: 0%, Max.: 100% |
20 to 98% | - | - |
Diagnostic Note:
|
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Actual VN Turbo Position
Actual VN Turbo Position #2 |
Actual VN turbo position/
Min.: 0%, Max.: 100% |
20 to 98% | - | - |
| Diagnostic Note:
If the vanes do not move smoothly or become stuck, the difference between the actual value and the target value becomes larger, and as a result, the motor duty also becomes larger.
|
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| VN Position Sensor Out
VN Position Sensor Out #2 |
VN position sensor output voltage/
Min.: 0 V, Max.: 5 V |
Idling after engine warmed-up: 1.0 to 3.0 V | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| VN Motor Duty
VN Motor Duty #2 |
VN turbo motor duty/
Min.: 0%, Max.: 127.5% |
0 to 100% | - | - |
| Diagnostic Note:
If the vanes do not move smoothly, the duty will increase towards 100%. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| VN Close Learn Value
VN Close Learn Value #2 |
VN turbo fully closed position learned value/
Min.: 0 V, Max.: 5 V |
1.5 to 2.0 V | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| VN Turbo Type | VN turbo type/
Not, Commo or Vacuum |
Commo | - | - |
| Diagnostic Note:
Indicates the VN turbo vane actuation method. ·
DC motor system. ·
Negative-pressure diaphragm system. ·
Step motor system. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| VN Turbo Max Angle | VN turbo maximum opening amount/
Min.: 0%, Max.: 100% |
- | - | - |
| Diagnostic Note:
·
The maximum vane opening amount is displayed in %. ·
The VN turbo is operated between VN Turbo Max Angle and VN Turbo Min Angle when the Test the Turbo Charger Step Motor Active Test is performed. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| VN Turbo Min Angle | VN turbo minimum opening amount/
Min.: 0%, Max.: 100% |
- | - | - |
| Diagnostic Note:
·
The minimum vane opening amount is displayed in %. ·
The VN turbo is operated between VN Turbo Max Angle and VN Turbo Min Angle when the Test the Turbo Charger Step Motor Active Test is performed. |
||||
Diesel Starting
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Glow Relay Request
Glow Relay Request #2 |
Status of the glow relay request/
ON or OFF |
- | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Glow Indicator | Status of the glow indicator/
ON or OFF |
- | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Starter Signal | Starter signal/
ON or OFF |
ON: Cranking | - | ·
OFF malfunction (ignition switch (STA) is ON but the signal is OFF and the starter is operating): Wire harness is open or shorted to ground ·
ON malfunction (ignition switch (STA) is off but the signal is ON and the starter is not operating): Wire harness is shorted to +B ·
Operation malfunction: ignition switch malfunction, starter relay malfunction, starter malfunction, battery or battery cable is defective, or wire harness is open or shorted |
| Symptoms when out of range:
·
Ignition switch ON but the starter does not operate: Starting is not possible ·
Ignition switch is off but the starter continues to operate: STA signal malfunction (P0617) is stored |
||||
| Diagnostic Note:
Ignition switch (STA) output: ·
ON: Starter is operating ·
OFF: Starter is not operating |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Neutral Position SW Signal | Neutral position switch status/
ON or OFF |
ON: Shift lever in neutral | Switch output (neutral position switch) | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Clutch Switch | Clutch switch/
ON or OFF |
ON: Clutch pedal depressed | Switch output (clutch switch) | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Clutch Start Switch | Clutch start switch/
ON or OFF |
ON: Clutch pedal depressed | Switch output (clutch start switch) | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Immobiliser Communication | Immobiliser communication/
ON or OFF |
·
ON: Normal ·
OFF: Engine cannot be started due to immobiliser communication malfunction |
- | ·
Use of a non-registered key ·
Key battery is fully depleted |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Engine Speed (Starter Off) | Engine speed when starter off/
Min.: 0 rpm, Max.: 1594 rpm |
- | - | - |
| Diagnostic Note:
Engine speed immediately after starting the engine. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Starter Count | Starter on count/
Min.: 0, Max.: 255 |
- | - | - |
| Diagnostic Note:
Number of times the starter turned on from the time the ignition switch was turned to ON. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Run Dist of Previous Trip | Distance driven during previous trip/
Min.: 0 km, Max.: 261 km |
- | - | - |
| Diagnostic Note:
Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip. After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.
|
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Glow Request Lighting Time | Glow request lighting time/
Min.: 0 ms, Max.: 33423 ms |
- | - | - |
| Diagnostic Note:
·
By comparing Glow Request Lighting Time to IG-ON Time, the operation state (whether the engine was started, etc.) can be determined. ·
If the malfunction occurred when starting a cold engine at 0°C (32°F) or less, this item is useful in determining whether the engine was started after the glow plug indicator lights turned off. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| IG-ON Time | IG-ON time/
Min.: 0 ms, Max.: 33423 ms |
- | - | - |
| Diagnostic Note:
·
By comparing Glow Request Lighting Time to IG-ON Time, the operation state (whether the engine was started, etc.) can be determined. ·
If the malfunction occurred when starting a cold engine at 0°C (32°F) or less, this item is useful in determining whether the engine was started after the glow plug indicator lights turned off. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Engine Starting Time | Engine starting time/
Min.: 0 ms, Max.: 267000 ms |
- | - | - |
| Diagnostic Note:
This is the time elapsed after the starter turns on until the engine speed reaches 400 rpm. This value is cleared 5 seconds after the engine is started and the value is displayed as 0 ms. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Immobiliser Fuel Cut History | Immobiliser fuel cut history/
ON or OFF |
OFF | - | - |
| Diagnostic Note:
If Immobiliser Fuel Cut History was "ON" when DTC P1604 (Startability Malfunction) was stored, the engine could not be started due to the immobiliser. |
||||
Diesel Rough
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Electric Duty Feedback Value | Electric load feedback value/
Min.: 0 mm3/st, Max.: 39.8 mm3/st |
0 to 2.5 mm3/st | - | - |
| Diagnostic Note:
Expected injection volume increase after the electrical load turns from off to on. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| A/C Duty Feedback Value | A/C load feedback value/
Min.: 0 mm3/st, Max.: 39.8 mm3/st |
0 to 4.1 mm3/st | - | - |
| Diagnostic Note:
Expected injection volume increase after the A/C turns from off to on. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| PS Duty Feedback Value | Power steering load feedback value/
Min.: 0 mm3/st, Max.: 39.8 mm3/st |
- | - | - |
| Diagnostic Note:
This item is displayed on the GTS but is not used. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Idle Injection Volume (Min) | Idle minimum injection volume/
Min.: 0 mm3/st, Max.: 39.8 mm3/st |
- | - | - |
Support Data (Monitor Support Status)
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Intake Air Temp (Turbo) Supported | Intake Air Temperature (Turbo) Support/
Unsupp or Supp |
- | *1 |
| Glow Indicator Supported | Glow Indicator Support/
Unsupp or Supp |
- | *1 |
| Target Throttle Position Supported | Target Throttle Position Support/
Unsupp or Supp |
- | *1 |
| Target Throttle Position #2 Supported | Target Throttle Position #2 Support/
Unsupp or Supp |
- | *1 |
| Actual Throttle Position Supported | Actual Throttle Position Support/
Unsupp or Supp |
- | *1 |
| Actual Throttle Position #2 Supported | Actual Throttle Position #2 Support/
Unsupp or Supp |
- | *1 |
| Target Common Rail Pressure Supported | Target Common Rail Pressure Support/
Compl or Incmpl |
- | *1 |
| Common Rail Pressure Supported | Common Rail Pressure Support/
Unsupp or Supp |
- | *1 |
| Fuel Temperature Supported | Fuel Temperature Support/
Unsupp or Supp |
- | *1 |
| Target EGR Valve Pos Supported | Target EGR Valve Pos Support/
Unsupp or Supp |
- | *1 |
| Target EGR Valve Pos #2 Supported | Target EGR Valve Pos #2 Support/
Unsupp or Supp |
- | *1 |
| Actual EGR Valve Pos Supported | Actual EGR Valve Pos Support/
Unsupp or Supp |
- | *1 |
| Actual EGR Valve Pos #2 Supported | Actual EGR Valve Pos #2 Support/
Unsupp or Supp |
- | *1 |
| Target Booster Pressure Supported | Target Booster Pressure Support/
Unsupp or Supp |
- | *1 |
| VN Turbo Command Supported | VN Turbo Command Support/
Unsupp or Supp |
- | *1 |
| VN Turbo Command #2 Supported | VN Turbo Command #2 Support/
Unsupp or Supp |
- | *1 |
| Actual VN Position Supported | Actual VN Position Support/
Unsupp or Supp |
- | *1 |
| Actual VN Position #2 Supported | Actual VN Position #2 Support/
Unsupp or Supp |
- | *1 |
| *1:
Supp: The item is supported by the vehicle. Unsupp: The monitor is not supported by the vehicle. |
|||
AT (for Automatic Transmission)
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Shift SW Status (P Range) | Park/neutral position switch status/
ON or OFF |
·
ON: Shift lever in P ·
OFF: Shift lever not in P |
- | - |
| Diagnostic Note:
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Shift SW Status (R Range) | Park/neutral position switch status/
ON or OFF |
·
ON: Shift lever in R ·
OFF: Shift lever not in R |
- | - |
| Diagnostic Note:
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Shift SW Status (N Range) | Park/neutral position switch status/
ON or OFF |
·
ON: Shift lever in N ·
OFF: Shift lever not in N |
- | - |
| Diagnostic Note:
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Shift SW Status (N,P Range) | Park/neutral position switch status/
ON or OFF |
·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
- | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Shift SW Status (D Range) | Park/neutral position switch status/
ON or OFF |
·
ON: Shift lever in D, S, "+" or "-" ·
OFF: Shift lever not in D, S, "+" or "-" |
- | - |
| Diagnostic Note
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Shift Status | ECM gearshift command/
1st, 2nd, 3rd, 4th, 5th and 6th |
Same as actual gear ratio | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| SPD (NT) | Input turbine speed/
Min.: 0 rpm, Max.: 12750 rpm |
·
Lock-up ON (After warming up engine): Input turbine speed (NT) equal to engine speed ·
Lock-up OFF (Idling at P or N position): Input turbine speed (NT) nearly equal to engine speed |
- | - |
| Diagnostic Note:
Data is displayed in increments of 50 rpm. |
||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| Lock Up | Lock-up/
ON or OFF |
·
ON: Lock up operating ·
OFF: Lock up not operating |
- | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
|---|---|---|---|---|
| A/T Oil Temperature 1 | ATF temperature sensor value/
Min.: -40°C, Max.: 215°C |
With engine cold:
Equal to ambient temperature |
- | - |
| Diagnostic Note:
If the value is -40°C (-40°F) or 150°C (302°F), the ATF temperature sensor circuit is open or shorted. |
||||
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Engine and ECT / Active Test.
Perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the A/C Cut Signal | Control the A/C signal | ON/OFF | Confirm that the vehicle is stopped and the engine is idling |
| Control the ACM Inhibit | Control the VSV for engine mount | ON/OFF | - |
| Connect the TC and TE1 | Turn on the TC and TE1 connection | ON/OFF | - |
| Control the EGR Step Position | Control the No. 1 EGR valve assembly | 0 to 100% | Test is possible when the following conditions are met:
·
Ignition switch ON. ·
Engine is stopped. |
| Control the EGR Step Position #2 | Control the No. 2 EGR valve assembly | ||
| Test the Turbo Charger Step Motor | Activate the turbocharger sub-assembly (for bank 1) | 0 to 100% | Test is possible when the following conditions are met:
·
Ignition switch ON. ·
Engine is stopped. |
| Test the Turbo Charger Step Motor #2 | Activate the turbocharger sub-assembly (for bank 2) | ||
| Diesel Throttle Target Angle | Control the diesel throttle valve (for bank 1) | 0 to 90% | Test is possible when the following conditions are met:
·
Ignition switch ON. ·
Engine is stopped. |
| Diesel Throttle Target Angle #2 | Control the diesel throttle valve (for bank 2) | ||
| Test the Fuel Leak | Pressurize the common rail interior and check for fuel leaks | Stop/Start | ·
Fuel pressure inside common rail set to specified value and engine speed increased to 2000 rpm when ON is selected ·
Above conditions preserved while test is ON
|
| Activate the VN Turbo Open | Activate the turbocharger sub-assembly (for bank 1 and bank 2) | ON/OFF | Confirm that the engine is running. |
| Activate the EGR Valve Close | Activate the No. 1 and No. 2 EGR valve assembly | ON/OFF | Confirm that the vehicle is stopped and the engine is idling |
| Control the Select Cylinder Fuel Cut | Selected cylinder (cylinder #1 to #8) injector assembly fuel cut | #1/#2/#3/#4/#5/#6/#7/#8
ON/OFF |
Fuel injection is stopped while the test is ON.
·
Confirm that the vehicle is stopped and the engine is idling. ·
If the running condition of the engine does not worsen even though injection of the designated cylinder is stopped, the cylinder can be determined to be malfunctioning. |
| Control the ALL Cylinders Fuel Cut | Injector fuel cut for all cylinders | ON/OFF | Fuel injection stops in all cylinders. |
| Check the Cylinder Compression* | Check the cylinder compression pressure | ON/OFF | Fuel injection stops in all cylinders. |
*: When cranking the engine, the Active Test measures the speed of each cylinder. In this Active Test, the fuel of all cylinders is cut when the engine is cranked for approximately 10 seconds.
At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Active Test / Check the Cylinder Compression.
If the results are not displayed normally, select the display items from the Data List before performing the Active Test. Enter the following menus: Engine and ECT / Data List / Compression / Engine Speed of Cyl #1, Engine Speed of Cyl #2, Engine Speed of Cyl #3, Engine Speed of Cyl #4, Engine Speed of Cyl #5, Engine Speed of Cyl #6, Engine Speed of Cyl #7, Engine Speed of Cyl #8 and Av Engine Speed of All Cyl.
Push the snapshot button to turn the snapshot function on.
Using the snapshot function, data can be recorded during the Active Test.
While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.
After performing the above procedure, the "Check the Cylinder Compression" Active Test will start. Fuel injection for all cylinders is prohibited and the engine speed measurement of each cylinder enters standby mode.
Crank the engine for about 10 seconds.
Continue to crank the engine until the values change from the default value (51199 rpm).
Monitor the engine speed (Engine Speed of Cyl #1 to #8, Av Engine Speed of All Cyl) displayed on the GTS.
At first, the Tester Display will show the engine speed measurement of each cylinder to be extremely high. After approximately 10 seconds of engine cranking, the engine speed measurement of each cylinder will change to the actual engine speed.
After the "Check the Cylinder Compression" Active Test is turned on, it will automatically turn off after 255 seconds.
When the "Check the Cylinder Compression" test is off and the engine is cranked, the engine will start.
If the "Check the Cylinder Compression" test needs to be performed after it is turned on and performed once, press "EXIT" to return to the Active Test menu screen. Then perform the "Check the Cylinder Compression" test again.
Use a fully-charged battery.
Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.
If the Active Test is changed to OFF while the engine is being cranked, the engine will start.
Push the snapshot button to turn the snapshot function off.
Select "Stored Data" on the GTS screen, select the recorded data and display the data as a graph.
If the data is not displayed as a graph, the change of the values cannot be observed.
Check the change in engine speed values.
As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.