1.INSPECT TIRES
Check the tires for wear and proper inflation pressure.
| Tire size | Front
kPa (kgf/cm2, psi) |
Rear
kPa (kgf/cm2, psi) |
|---|---|---|
| 285/65R17 116H | 230 (2.3, 33) | 230 (2.3, 33) |
| 285/60R18 116V | 240 (2.4, 35)*1
230 (2.3, 33)*2 |
240 (2.4, 35)*1
230 (2.3, 33)*2 |
| 285/50R20 112V | 240 (2.4, 35)*1
230 (2.3, 33)*2 |
240 (2.4, 35)*1
230 (2.3, 33)*2 |
| 260 (2.6, 38)*3 |
*1: For EU (Member States of European Union)
*2: Except EU (Member States of European Union)
*3: For driving at over 160 km/h (100 mph)
| Tire size | Front
kPa (kgf/cm2, psi) |
Rear
kPa (kgf/cm2, psi) |
|---|---|---|
| 245/75R17 112H | 230 (2.3, 33) | 230 (2.3, 33) |
| 260 (2.6, 38)* | ||
| 285/65R17 116H | 230 (2.3, 33) | 230 (2.3, 33) |
| 285/60R18 116V | 230 (2.3, 33) | 230 (2.3, 33) |
| 285/50R20 112V | 230 (2.3, 33) | 230 (2.3, 33) |
| 260 (2.6, 38)* |
*: For driving at over 160 km/h (100 mph)
| Tire size | Front
kPa (kgf/cm2, psi) |
Rear
kPa (kgf/cm2, psi) |
|---|---|---|
| 285/65R17 116H | 230 (2.3, 33) | 230 (2.3, 33) |
| 285/60R18 116V | 230 (2.3, 33) | 230 (2.3, 33) |
| Tire size | Front
kPa (kgf/cm2, psi) |
Rear
kPa (kgf/cm2, psi) |
|---|---|---|
| 245/75R17 112H | 230 (2.3, 33) | 230 (2.3, 33) |
| 260 (2.6, 38)* | ||
| 285/65R17 116H | 230 (2.3, 33) | 230 (2.3, 33) |
| 285/60R18 116V | 230 (2.3, 33) | 230 (2.3, 33) |
| 285/50R20 112V | 230 (2.3, 33) | 230 (2.3, 33) |
| 260 (2.6, 38)* |
*: For driving at over 160 km/h (100 mph)
Tire pressure adjustment method when warm (w/ Tire Pressure Warning System):
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Adjust the tire pressure so that the displayed value is equal to the set pressure.
Perform initialization and check that initialization completes.
(See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION)
Check and record the value of the Data List item "Temperature in Tire". (Ts)
Check and record the ambient temperature during tire pressure adjustment. (Tm)
Readjust the tire pressure according to the difference between the tire internal temperature (Ts) and the ambient temperature (Tm). (P)
Tire internal temperature: Ts, Ambient temperature: Tm, Tire pressure readjustment value: PP = (Specified Pressure) + (Ts - Tm)
Check the pressure adjustment value with the Data List item "Tire Inflation Pressure".
Check the tire pressure warning system description for the relationship between the inflation pressure and tire pressure warning pressure.
(See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>SYSTEM DESCRIPTION)
Using a dial indicator, check the runout of the tires.
3.0 mm (0.118 in.) or less
Remove the wheel assembly from the vehicle, and measure the wheel assembly alone.
2.ROTATE TIRES
Rotate the tires as shown in the illustration.
| *a | Front of the Vehicle |
3.INSPECT WHEEL BALANCE
for Steel Wheel Type:
Check and adjust the off-the-car balance.
12 g (0.0265 lb) or less
If necessary, check and adjust the on-the-car balance.
for Aluminum Wheel Type:
Check and adjust the off-the-car balance.
| Tire Size | Standard Imbalance After Adjustment |
|---|---|
| 285/65R17 116H | 7.5 g (0.0165 lb) or less |
| 285/60R18 116V | 7.0 g (0.0154 lb) or less |
| 285/50R20 112V | 6.5 g (0.0143 lb) or less |
Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be attached.
Do not touch the adhesive surface of the tape.
Attach a sticking-type balance weight to the flat surface (A) shown in the illustration.
20 mm (0.787 in.)
Push the balance weight firmly so that it securely adheres to the position.
Do not reuse the balance weight.
If necessary, check and adjust the on-the-car balance.
4.INSPECT FRONT AXLE HUB
5.INSPECT REAR AXLE SHAFT