Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM38G0E _59 Vehicle Exterior _100456 WIPER / WASHER _0467203 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B609907N02
3.458,0.938 4.5,1.177 1.042,0.24 5,2.469 5.417,2 5.417,2 5.583,2 false 4.5,1.083 4.667,1.083 4.667,1.083 5.115,1.698 false 1.135,4.281 1.583,4.281 false 5.219,1.74 5.531,1.938 0.313,0.198 10 false x 2 0.938,4.177 1.5,4.594 0.563,0.417 18 false 1 5.688,1.927 6,2.125 0.313,0.198 10 false *1 3.542,0.99 5.021,1.344 1.479,0.354 8 false 7.5 (76, 66 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 WINDSHIELD WIPER MOTOR ASSEMBLY 85110 (Click here) - -

*1 FRONT WIPER LINK - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
V100135

MP Grease

B604561N01
0.25,2.573 1.417,2.802 1.167,0.229 3.698,1.375 4.531,1.635 0.833,0.26 5.75,2.51 6.583,2.771 0.833,0.26 2,4.417 3.75,5.75 1.75,1.333 0.083,3.583 1.833,4.917 1.75,1.333 6.125,2.146 6.125,2.51 false 0.75,2 0.583,2.417 0.583,2.417 0.417,2.417 false 6.417,3.708 6.583,3.083 6.583,3.083 6.75,3.083 false 5.417,5.083 5.667,4.833 5.667,4.833 5.833,4.833 false 0.719,4.5 0.583,4.75 0.583,4.75 0.417,4.75 false 4.083,1 4.083,1.375 false 4,0.583 4.083,0.333 4.083,0.333 4.25,0.333 false 1.677,3.281 2.229,3.281 false 3.417,4.667 3.25,4.667 3.25,4.667 3.167,5 false 1.333,0.75 1.646,0.75 false 2.583,1.833 2.917,1.833 false 5.344,1.417 5.51,1.083 5.51,1.083 5.677,1.083 false 3.75,0.802 3.917,0.802 false 5.75,1.969 5.917,1.969 false 2.833,2.667 3.167,2.667 false 1.417,2.625 1.719,2.625 false 1.333,3.156 1.615,3.51 0.281,0.354 18 false 2 0.188,4.583 0.469,4.938 0.281,0.354 18 false 7 3.469,4.51 3.75,4.865 0.281,0.354 18 false 8 0.188,2.25 0.469,2.604 0.281,0.354 18 false 4 5.917,4.667 6.198,5.021 0.281,0.354 18 false 5 2.302,1.635 2.583,1.99 0.281,0.354 18 false 3 4.531,0.188 5.375,0.563 0.844,0.375 18 false 11, 12 1.969,2.563 2.25,2.917 0.281,0.354 10 false x 3 1.083,0.583 1.365,0.938 0.281,0.354 18 false 9 6.76,2.917 7.146,3.292 0.385,0.375 18 false 10 3.375,0.646 3.854,1.01 0.479,0.365 18 false 15 5.354,1.813 5.833,2.177 0.479,0.365 18 false 15 3.813,1.417 5.646,1.615 1.833,0.198 8 false 26 (265, 19) 5.854,2.583 6.948,2.833 1.094,0.25 8 false 26 (265, 19) 0.354,2.615 3.417,2.813 3.063,0.198 8 false 5.5 (56, 49 in.*lbf) 3.052,1.115 3.365,1.313 0.313,0.198 10 false x 2 3.25,2.5 3.531,2.854 0.281,0.354 18 false 6 5.927,0.927 6.771,1.302 0.844,0.375 18 false 13, 14 0.135,3.635 0.448,3.833 0.313,0.198 12 false *A 2.052,4.469 2.365,4.667 0.313,0.198 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

2 WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY - (Click here) - -
3 COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY 55708 (Click here) - -
4 COWL TOP VENTILATOR LOUVER RH 55781D - - -
5 COWL TOP VENTILATOR LOUVER LH 55782D - - -
6 HOOD TO COWL TOP SEAL 53383B - - -
7 ENGINE SIDE COVER RH 51473C - - -
8 ENGINE SIDE COVER LH 51474B - - -
9 WINDSHIELD OUTSIDE MOULDING RH 75533 - - -
10 WINDSHIELD OUTSIDE MOULDING LH 75534 - - -
11 FRONT WIPER ARM AND BLADE ASSEMBLY RH - (Click here) - -
12 FRONT WIPER ARM AND BLADE ASSEMBLY RH - (Click here) - -
13 FRONT WIPER ARM AND BLADE ASSEMBLY LH - (Click here) - -
14 FRONT WIPER ARM AND BLADE ASSEMBLY LH - (Click here) - -
15 FRONT WIPER ARM HEAD CAP 85292B - - -

*A except 1GR-FE - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

NOTICE:

Make sure to hold the front wiper arm while lifting it, as lifting the front wiper arm by the front wiper blade may damage or deform the front wiper blade.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.
B609925C02
0.51,2.292 1.167,2.74 0.656,0.448 18 false iii 3.667,2.292 4.323,2.74 0.656,0.448 18 false iv 4.552,2.042 5.208,2.49 0.656,0.448 18 false ii 4.417,0.5 4.604,0.792 0.188,0.292 18 true i 3.302,0.49 3.49,0.781 0.188,0.292 18 true i
V113147

Install in this Direction
V100155

Apply MP Grease


i.

Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly to the wiper link assembly with the 2 "TORX" screws.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


ii.

Connect the connector.


iii.

Apply MP grease to the wiper motor pivot.


iv.

Connect the No. 1 wiper link rod to the wiper motor pivot.



Hide 2.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

a.
B613412C02
2.75,0.833 3.25,0.333 3.25,0.333 3.417,0.333 true 1.281,1.396 1.469,1.604 0.188,0.208 10 true (2) 5.125,1.708 5.417,1.906 0.292,0.198 10 true (1) 1.76,1.094 1.948,1.302 0.188,0.208 10 true (2) 3.5,0.219 3.813,0.417 0.313,0.198 10 false *1 2.323,0.104 2.656,0.365 0.333,0.26 18 true i, ii 4.469,2.469 4.708,2.792 0.24,0.323 18 true iii 5.365,1.385 5.604,1.708 0.24,0.323 18 true iv 1.479,0.969 1.688,1.26 0.208,0.292 18 true iv
*1 Motor Grommet - -


i.

Temporarily install the front wiper motor and link assembly to the vehicle.

NOTICE:

Do not damage the vehicle with the front wiper motor and link.



ii.

Engage the motor grommet as shown in the illustration.


iii.

Connect the connector.


iv.

Install the windshield wiper motor and link assembly with the 3 bolts in the order shown in the illustration.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)



Hide 55708 3.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Z101186

NOTICE:

To prevent damage to the windshield glass, remove any foreign matter (sand, dust, etc.) from around the contacting surfaces of the cowl top ventilator louver sub-assembly and windshield glass.



a.
E467563C02
0,0 0,0 false
V113147

Install in this Direction - -



Hide 55781D 4.INSTALL COWL TOP VENTILATOR LOUVER RH

Hide 55782D 5.INSTALL COWL TOP VENTILATOR LOUVER LH

Hide 53383B 6.INSTALL HOOD TO COWL TOP SEAL

Hide 51473C 7.INSTALL ENGINE SIDE COVER RH (except 1GR-FE)

Hide 51474B 8.INSTALL ENGINE SIDE COVER LH (except 1GR-FE)

Hide 75533 9.INSTALL WINDSHIELD OUTSIDE MOULDING RH

Hide 75534 10.INSTALL WINDSHIELD OUTSIDE MOULDING LH

Hide 11.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (for LHD)

a.
B609929C03
2.083,1.583 2.333,1.083 2.333,1.083 2.5,1.083 true 2.083,2.667 2.5,3.083 2.5,3.083 2.667,3.083 true 5.167,2.802 5.521,2.583 true 2.25,2.417 2.583,2.083 2.583,2.083 2.75,2.083 true 5.417,3.333 5.625,3.167 true 2.75,2.969 3.063,3.167 0.313,0.198 10 false *a 2.583,1 2.896,1.198 0.313,0.198 10 false *a 5.229,3.313 5.5,3.5 0.271,0.188 10 false *d 0.417,0.073 0.729,0.396 0.313,0.323 18 false i 3.521,0.146 4.188,0.469 0.667,0.323 18 true ii, iii 0.198,3.75 0.51,4.073 0.313,0.323 18 true iv 2.833,1.969 3.146,2.167 0.313,0.198 10 false *b 4.323,2.823 4.5,3 0.177,0.177 10 true *e 5.583,2.458 5.865,2.667 0.281,0.208 10 false *c
*a Serration *b Wire Brush
*c Ceramic Dot *d Windshield Glass Edge
*e 29 to 49 mm (1.15 to 1.92 in.) - -


i.

When reusing the front wiper arm and blade assembly RH:

1. Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.



ii.

Set the automatic stop position by the below procedure.

1. Turn the ignition switch to ON.

2. Operate the windshield wipers while spraying washer fluid onto the windshield glass. Make sure that the windshield wipers function properly and the wipers do not contact the vehicle body.

3. Turn the ignition switch off.


iii.

Temporarily install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.


iv.

Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)

HINT:

Hold the arm hinge by hand when tightening the nut.




Hide 12.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (for RHD)

a.
B612060C03
1.188,1.594 1.083,1.083 1.083,1.083 0.917,1.083 true 1.25,2.667 1.667,3.083 1.667,3.083 1.833,3.083 true 5.854,2.823 5.583,2.583 true 1.833,2.417 2.167,2.083 2.167,2.083 2.333,2.083 true 5.417,3.302 5.219,3.021 true 1.927,2.99 2.24,3.188 0.313,0.198 10 false *a 0.719,0.99 1.031,1.188 0.313,0.198 10 false *a 5.427,3.323 5.698,3.51 0.271,0.188 10 false *d 0.417,0.073 0.729,0.396 0.313,0.323 18 false i 3.521,0.146 4.188,0.469 0.667,0.323 18 true ii, iii 0.198,3.75 0.51,4.073 0.313,0.323 18 true iv 2.427,2 2.74,2.198 0.313,0.198 10 false *b 6.417,2.823 6.594,3 0.177,0.177 10 false *e 5.417,2.417 5.698,2.625 0.281,0.208 10 false *c
*a Serration *b Wire Brush
*c Ceramic Dot *d Windshield Glass Edge
*e 25 to 45 mm (0.985 to 1.77 in.) - -


i.

When reusing the front wiper arm and blade assembly RH:

1. Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.



ii.

Set the automatic stop position by the below procedure.

1. Turn the ignition switch to ON.

2. Operate the windshield wipers while spraying washer fluid onto the windshield glass. Make sure that the windshield wipers function properly and the wipers do not contact the vehicle body.

3. Turn the ignition switch off.


iii.

Temporarily install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.


iv.

Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)

HINT:

Hold the arm hinge by hand when tightening the nut.




Hide 13.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH (for LHD)

a.
B609930C03
2.083,1.563 2.333,1.083 2.333,1.083 2.5,1.083 true 4.75,2.833 5.021,2.563 true 2.083,2.708 2.469,3 2.469,3 2.635,3 true 2.333,2.417 2.583,2.083 2.583,2.083 2.75,2.083 true 5.167,3.26 5.042,3.031 true 2.583,1 2.896,1.198 0.313,0.198 10 false *a 2.667,2.917 2.979,3.115 0.313,0.198 10 false *a 0.438,0.052 0.719,0.427 0.281,0.375 18 false i 3.521,0.042 3.927,0.427 0.406,0.385 18 true ii 0.083,3.823 0.448,4.208 0.365,0.385 18 true iii 2.833,2 3.146,2.198 0.313,0.198 10 false *b 5.01,2.417 5.25,2.625 0.24,0.208 10 false *c 4.083,2.833 4.323,3.042 0.24,0.208 10 false *e 5.177,3.292 5.417,3.5 0.24,0.208 10 false *d
*a Serration *b Wire Brush
*c Ceramic Dot *d Windshield Glass Edge
*e 25 to 45 mm (0.985 to 1.77 in.) -


i.

When reusing the front wiper arm and blade assembly LH:

1. Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.



ii.

Temporarily install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.


iii.

Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)

HINT:

Hold the arm hinge by hand when tightening the nut.




Hide 14.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH (for RHD)

a.
B612059C02
1.188,1.594 1.083,1.083 1.083,1.083 0.917,1.083 true 1.25,2.667 1.667,3.083 1.667,3.083 1.833,3.083 true 5.406,2.813 5.229,2.552 true 1.833,2.417 2.167,2.083 2.167,2.083 2.333,2.083 true 5.167,3.333 5.271,3.135 true 1.927,2.99 2.24,3.188 0.313,0.198 10 false *a 0.719,0.99 1.031,1.188 0.313,0.198 10 false *a 5,3.333 5.271,3.521 0.271,0.188 10 false *d 0.417,0.073 0.729,0.396 0.313,0.323 18 false i 3.583,0.146 4.25,0.469 0.667,0.323 18 true ii 0.198,3.75 0.51,4.073 0.313,0.323 18 true iii 2.427,2 2.74,2.198 0.313,0.198 10 false *b 6.167,2.833 6.667,3.073 0.5,0.24 10 false *e 5.083,2.375 5.365,2.583 0.281,0.208 10 false *c
*a Serration *b Wire Brush
*c Ceramic Dot *d Windshield Glass Edge
*e 29 to 49 mm (1.15 to 1.92 in.) - -


i.

When reusing the front wiper arm and blade assembly LH:

1. Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.



ii.

Temporarily install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.


iii.

Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)

HINT:

Hold the arm hinge by hand when tightening the nut.




Hide 85292B 15.INSTALL FRONT WIPER ARM HEAD CAP