Home › Vehicle Exterior › WIPER / WASHER › RAIN SENSOR
RM38G0E _59 Vehicle Exterior _100456 WIPER / WASHER _0467218 RAIN SENSOR A

WIPER / WASHER  RAIN SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
E464689N01
1.958,0.927 2.615,0.927 false 2.51,2.052 3.167,2.052 false 5.115,0.927 5.698,0.927 false 2.323,1.938 2.604,2.292 0.281,0.354 18 false 2 5.76,0.792 6.042,1.146 0.281,0.354 18 false 3 1.792,0.802 2.073,1.156 0.281,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 RAIN SENSOR TAPE 89944 (Click here) - -
2 RAIN SENSOR 89941 (Click here) - -
3 RAIN SENSOR COVER 89943 - - -

PROCEDURE

Hide 89944 1.INSTALL RAIN SENSOR TAPE

a.
E442846N01
4.948,1.125 5.104,1.323 0.156,0.198 10 false A 5.167,1.583 5.323,1.781 0.156,0.198 10 false B 5.51,0.052 6.344,0.406 0.833,0.354 18 false iii 3.104,0.063 3.385,0.417 0.281,0.354 18 false ii 0.26,0.052 0.542,0.406 0.281,0.354 18 false i

HINT:

The rain sensor tape is reusable. Only replace the tape if it is damaged or contaminated with foreign matter.


i.

Remove the rain sensor tape.


ii.

Clean the rain sensor sensing portion with a piece of cloth.


iii.

Peel off the smaller release sheet, and then attach the rain sensor tape to the rain sensor sensing portion as shown in the illustration.

NOTICE:

Use your fingers to push out any air bubbles from under the tape.


Standard Clearance
Area Measurement
A 14.4 mm (0.567 in.)
B 7.25 mm (0.285 in.)



Hide 89941 2.INSTALL RAIN SENSOR

Z101186

NOTICE:
·

Make sure that there is no rain sensor tape residue remaining on the windshield glass. If there is, remove the residue.

·

If there is any rain sensor tape residue remaining on the windshield glass, replace the tape.




a.
E464690C04
1.615,4.479 1.417,4.479 1.417,4.479 1.417,4.042 true 0.646,0.292 0.823,0.563 0.177,0.271 18 true i 4.365,0.313 4.542,0.583 0.177,0.271 18 true ii 3.115,3.833 3.427,4.104 0.313,0.271 18 true iii 0.698,3.781 1.01,4.052 0.313,0.271 18 true iv 1.708,4.406 2.021,4.604 0.313,0.198 10 false *a
*a Stopper - -
V100135

Lock
V113147

Install in this Direction


i.

Clean the windshield glass with a piece of cloth.


ii.

When installing a new rain sensor or when the rain sensor tape has been replaced:

1.

Peel off the release sheet.

HINT:

Do not touch the silicone surface.




iii.

Gradually attach the rain sensor to the windshield glass surface in the direction indicated by the arrow shown in the illustration to prevent air bubbles from forming between them.

HINT:

Do not touch the silicone or glass surfaces.



iv.

Push in the stopper to install the rain sensor as shown in the illustration.


v.

Connect the connector.



Hide 89943 3.INSTALL RAIN SENSOR COVER

a.
E464692