Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › TRANSMISSION WIRE
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0467301 TRANSMISSION WIRE A

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION WIRE  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C456943N01
0.51,2.292 1.5,2.542 0.99,0.25 0.5,2.833 1.49,3.083 0.99,0.25 5.24,0.604 6.417,1.083 1.177,0.479 5.281,0.646 6.375,1.042 1.094,0.396 5.021,2.021 5.688,2.021 false 0.917,2 1.083,2 1.083,2 1.75,1.833 false 2.917,3 3.417,3 false 2.563,1.646 2.813,1.646 false 1.5,2.417 1.646,2.417 1.646,2.417 2.5,2 false 1.49,2.969 1.635,2.969 1.635,2.969 2.552,2.396 false 1.667,2.417 1.75,2.083 false 1.479,2.708 1.625,2.708 1.625,2.708 2.521,2.146 false 4.573,1.635 5.021,0.833 5.021,0.833 5.271,0.833 false 4.979,1.604 5.135,1.323 5.135,1.323 5.385,1.323 false 0.75,1.854 1.031,2.208 0.281,0.354 18 false 2 2.854,1.5 3.135,1.854 0.281,0.354 18 false 3 6.01,1.885 6.292,2.24 0.281,0.354 18 false 1 3.448,2.792 3.729,3.146 0.281,0.354 18 false 4 5.427,1.208 5.885,1.406 0.458,0.198 10 false ● 2.615,2.302 3.073,2.5 0.458,0.198 10 false x 3 0.563,2.333 3.01,2.49 2.448,0.156 8 false 5.4 (55, 48 in.*lbf) 0.542,2.885 2.99,3.042 2.448,0.156 8 false 5.4 (55, 48 in.*lbf) 5.365,0.677 6.448,0.854 1.083,0.177 8 false 5.4 (55, 48 in.*lbf) 5.375,0.854 6.385,1.021 1.01,0.167 8 false 4.8 (49, 42 in.*lbf)* 1.313,2.604 1.771,2.802 0.458,0.198 10 false *1 2.635,2.073 3.094,2.271 0.458,0.198 10 false x 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 TRANSMISSION WIRE 82125J (Click here) - -
2 TRANSMISSION REVOLUTION SENSOR (NT) 89413N - - -
3 TRANSMISSION REVOLUTION SENSOR (SP2) 89413V - - -
4 TRANSMISSION VALVE BODY ASSEMBLY 35400A - - -

*1 TRANSMISSION WIRE CLAMP - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
* For use with union nut wrench ● Non-reusable part
V100135

Toyota Genuine ATF WS - -

PROCEDURE

Hide 82125J 1.INSTALL TRANSMISSION WIRE

a.
C456929C01
0.563,0.094 1.01,0.375 0.448,0.281 18 false i 4.448,0.052 5.031,0.406 0.583,0.354 18 true ii, iii 0.531,2.031 0.833,2.396 0.302,0.365 18 true iv 2.042,2.313 2.271,2.542 0.229,0.229 10 true *a 4.135,2.01 4.385,2.344 0.25,0.333 18 true v
*a Torque Wrench Fulcrum Length - -
V113147

Push Up the Lever
V113148

Turn


i.

Coat a new O-ring with ATF, and install it to the transmission wire.


ii.

Pass the transmission wire through the installation mouth of the automatic transmission assembly.


iii.

Connect the transmission wire connector and raise the lever to engage the claw.

NOTICE:

Make sure that the O-ring is not cracked or jammed when installing the transmission wire.


HINT:

Push up the lever until the claw of the transmission wire connector makes a connection sound.



iv.

Using a 10 mm union nut wrench, install the bolt.

Torque:
Specified tightening torque : 5.4 N*m (55 kgf*cm, 48 in.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 185 mm (7.2835 in.)): 4.8 N*m (49 kgf*cm, 42 in.*lbf)




v.

Install the 3 transmission wire clamps with the 3 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)



Hide 89413N 2.INSTALL TRANSMISSION REVOLUTION SENSOR (NT)

Hide 89413V 3.INSTALL TRANSMISSION REVOLUTION SENSOR (SP2)

Hide 35400A 4.INSTALL TRANSMISSION VALVE BODY ASSEMBLY