| ● | Non-reusable part | ★ | Precoated part |
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
11209 1.REMOVE V-BANK COVER SUB-ASSEMBLY
11101E 2.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side of Bank 1)
Disconnect the camshaft position sensor (for Intake Side of Bank 1) connector.
Remove the bolt and camshaft position sensor (for Intake Side of Bank 1).
If the camshaft position sensor (for Intake Side of Bank 1) has been struck or dropped, replace it.
Perform this procedure only when reusing the camshaft position sensor (for Intake Side of Bank 1).
1. Remove the O-ring from the camshaft position sensor (for Intake Side of Bank 1).
Make sure to only remove the O-ring with bare hands.
When removing the O-ring, be careful not to damage the O-ring groove of the camshaft position sensor (for Intake Side of Bank 1).
If the O-ring groove of the camshaft position sensor (for Intake Side of Bank 1) is damaged, replace the camshaft position sensor (for Intake Side of Bank 1) with a new one.
11101E 3.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side of Bank 1)
Disconnect the camshaft position sensor (for Exhaust Side of Bank 1) connector.
Remove the bolt and camshaft position sensor (for Exhaust Side of Bank 1).
If the camshaft position sensor (for Exhaust Side of Bank 1) has been struck or dropped, replace it.
Perform this procedure only when reusing the camshaft position sensor (for Exhaust Side of Bank 1).
1. Remove the O-ring from the camshaft position sensor (for Exhaust Side of Bank 1).
Make sure to only remove the O-ring with bare hands.
When removing the O-ring, be careful not to damage the O-ring groove of the camshaft position sensor (for Exhaust Side of Bank 1).
If the O-ring groove of the camshaft position sensor (for Exhaust Side of Bank 1) is damaged, replace the camshaft position sensor (for Exhaust Side of Bank 1) with a new one.
11101E 4.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side of Bank 2)
Disconnect the camshaft position sensor (for Intake Side of Bank 2) connector.
Remove the bolt and camshaft position sensor (for Intake Side of Bank 2).
If the camshaft position sensor (for Intake Side of Bank 2) has been struck or dropped, replace it.
Perform this procedure only when reusing the camshaft position sensor (for Intake Side of Bank 2).
1. Remove the O-ring from the camshaft position sensor (for Intake Side of Bank 2).
Make sure to only remove the O-ring with bare hands.
When removing the O-ring, be careful not to damage the O-ring groove of the camshaft position sensor (for Intake Side of Bank 2).
If the O-ring groove of the camshaft position sensor (for Intake Side of Bank 2) is damaged, replace the camshaft position sensor (for Intake Side of Bank 2) with a new one.
11101E 5.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side of Bank 2)
Disconnect the camshaft position sensor (for Exhaust Side of Bank 2) connector.
Remove the bolt and camshaft position sensor (for Exhaust Side of Bank 2).
If the camshaft position sensor (for Exhaust Side of Bank 2) has been struck or dropped, replace it.
Perform this procedure only when reusing the camshaft position sensor (for Exhaust Side of Bank 2).
1. Remove the O-ring from the camshaft position sensor (for Exhaust Side of Bank 2).
Make sure to only remove the O-ring with bare hands.
When removing the O-ring, be careful not to damage the O-ring groove of the camshaft position sensor (for Exhaust Side of Bank 2).
If the O-ring groove of the camshaft position sensor (for Exhaust Side of Bank 2) is damaged, replace the camshaft position sensor (for Exhaust Side of Bank 2) with a new one.