Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › CRANKSHAFT POSITION SENSOR
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0467369 CRANKSHAFT POSITION SENSOR A

V35A-FTS ENGINE CONTROL  CRANKSHAFT POSITION SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A516014N01
1.885,4.188 2.542,4.396 0.656,0.208 1.833,4.146 2.583,4.438 0.75,0.292 2.396,3.25 2.813,3.25 false 5.938,2.688 6.177,2.469 6.177,2.469 6.365,2.469 false 2.875,3.417 3.177,3.146 3.177,3.146 3.365,3.146 false 2.927,4.063 2.927,4.292 2.927,4.292 2.583,4.292 false 5.344,4.094 5.646,3.823 5.646,3.823 5.833,3.823 false 6.438,2.313 6.719,2.667 0.281,0.354 18 false 2 3.75,3.01 4.031,3.365 0.281,0.354 18 false 1 2.271,3.156 2.552,3.51 0.281,0.354 10 false ● 1.927,4.229 2.813,4.469 0.885,0.24 8 false 10 (102, 7) 6.458,3.01 6.865,3.219 0.406,0.208 10 false x 3 5.906,3.688 6.188,4.042 0.281,0.354 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CRANKSHAFT POSITION SENSOR 11401G (Click here) - -
2 FRONT FENDER APRON TRIM PACKING D 53785B - - -
3 FRONT WHEEL - - - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) ● Non-reusable part
V100135

Engine oil - -

CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 11401G 1.INSTALL CRANKSHAFT POSITION SENSOR

a.
A516015C01
3.344,1.083 3.073,1.083 false 4.688,1.854 4.688,1.635 false 4.688,3.177 4.688,2.958 false 5.792,1.708 5.792,1.49 false 5.813,3.083 5.813,2.865 false 4.708,2.396 4.906,2.094 4.906,2.094 5.073,2.094 true 6.542,2.854 6.292,2.854 false 6.365,1.75 6.177,1.75 6.177,1.75 6.052,1.625 false 6.417,0.76 6.25,0.76 6.25,0.76 6.052,0.885 false 5.469,2.344 5.75,2.344 false 4.719,1.042 4.917,0.74 4.917,0.74 5.083,0.74 true 4.635,1.896 4.948,2.052 0.313,0.156 10 false *1 3.396,1 3.708,1.156 0.313,0.156 10 false *b 4.167,0.771 4.479,0.927 0.313,0.156 10 false *c 4.156,2.177 4.469,2.333 0.313,0.156 10 false *d 5.094,0.615 5.406,0.771 0.313,0.156 10 false *a 4.625,3.208 4.938,3.365 0.313,0.156 10 false *1 5.719,1.74 6.031,1.896 0.313,0.156 10 false *1 5.76,3.156 6.073,3.313 0.313,0.156 10 false *1 6.469,0.656 6.781,0.813 0.313,0.156 10 false *a 6.438,1.667 6.75,1.823 0.313,0.156 10 false *a 5.302,2.24 5.615,2.396 0.313,0.156 10 false *a 6.583,2.76 6.896,2.917 0.313,0.156 10 false *a 5.125,1.958 5.438,2.115 0.313,0.156 10 false *a 4.833,1.156 5.052,1.365 0.219,0.208 10 false A 4.844,2.521 5,2.74 0.156,0.219 10 false B 4.438,1.146 4.573,1.313 0.135,0.167 10 true A 4.479,2.521 4.615,2.688 0.135,0.167 10 true B 5.833,0.552 6.427,0.844 0.594,0.292 10 false A - A 5.875,2.042 6.469,2.333 0.594,0.292 10 false B - B 0.479,0.073 1.031,0.427 0.552,0.354 18 false i, ii 0.396,1.99 0.906,2.302 0.51,0.313 18 true iii, iv
*1 O-ring - -
*a Seam *b Crankshaft Position Sensor Tip
*c Correct *d Incorrect


i.

Perform this procedure only when reusing the crankshaft position sensor.

1. Clean the O-ring groove of the crankshaft position sensor.

NOTICE:

Make sure the O-ring groove is free of foreign matter.


2. Install a new O-ring to the crankshaft position sensor.

NOTICE:

Set the O-ring on the tip of the crankshaft position sensor and roll it into the O-ring groove with bare hands to install it.


3. Check if the O-ring is twisted.

HINT:

Check the entire circumference of the seam of the O-ring for twisting.



ii.

Apply a light coat of engine oil to the O-ring of the crankshaft position sensor.


iii.

Install the crankshaft position sensor with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the crankshaft position sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the crankshaft position sensor.




iv.

Connect the crankshaft position sensor connector.



Hide 53785B 2.INSTALL FRONT FENDER APRON TRIM PACKING D

Hide 3.INSTALL FRONT WHEEL