Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › AIR FUEL RATIO SENSOR
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0467375 AIR FUEL RATIO SENSOR A

V35A-FTS ENGINE CONTROL  AIR FUEL RATIO SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A486417N05
2.896,3.25 3.729,3.594 0.833,0.344 5.302,2.531 6.135,2.875 0.833,0.344 2.073,1.281 2.906,1.625 0.833,0.344 4.594,0.75 5.427,1.094 0.833,0.344 2.406,3.094 2.406,3.427 2.406,3.427 2.896,3.427 false 1.615,1.573 1.813,1.448 1.813,1.448 2.063,1.448 false 4.875,2.708 5.292,2.708 false 4.094,1.01 4.313,0.917 4.313,0.917 4.583,0.917 false 4.135,3.302 4.51,3.615 0.375,0.313 18 false 4 3.333,1.333 3.708,1.646 0.375,0.313 18 false 3 6.552,2.604 6.927,2.917 0.375,0.313 18 false 2 5.823,0.792 6.198,1.104 0.375,0.313 18 false 1 2.948,3.271 3.771,3.427 0.823,0.156 8 false 44 (449, 32) 2.948,3.438 3.771,3.594 0.823,0.156 8 false 37.7 (384, 28)* 5.354,2.719 6.25,2.917 0.896,0.198 8 false 37.7 (384, 28)* 5.354,2.563 6.177,2.719 0.823,0.156 8 false 44 (449, 32) 2.125,1.458 2.948,1.615 0.823,0.156 8 false 37.7 (384, 28)* 4.635,0.927 5.458,1.083 0.823,0.156 8 false 37.7 (384, 28)* 2.125,1.323 2.948,1.479 0.823,0.156 8 false 44 (449, 32) 4.646,0.792 5.469,0.948 0.823,0.156 8 false 44 (449, 32)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 4 AIR FUEL RATIO SENSOR 89467E (Click here) - -
2 NO. 3 AIR FUEL RATIO SENSOR 89467D (Click here) - -
3 NO. 2 AIR FUEL RATIO SENSOR 89467C (Click here) - -
4 AIR FUEL RATIO SENSOR 89467B (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque * For use with SST

A490327N01
4.271,3 5.01,3.188 0.74,0.188 2.708,1.833 3.448,2.021 0.74,0.188 0.958,3.25 0.958,2.656 false 0.958,2.969 1.917,2.969 false 6.531,0.24 6.792,0.24 false 4.271,3.083 4.021,3.083 4.021,3.083 4.021,2.781 false 2.708,1.938 2.458,1.938 2.458,1.938 2.458,1.75 false 2.625,0.583 2.896,0.583 2.896,0.583 3.271,1 false 4.656,2.042 5.094,2.438 5.094,2.438 5.333,2.438 false 5.333,0.594 5.677,0.594 false 5.823,1.281 6.167,1.281 false 0.896,3.302 1.448,3.656 0.552,0.354 18 false 9 6.208,0.115 6.76,0.469 0.552,0.354 18 false 10 2.583,1.625 3.042,1.823 0.458,0.198 10 false x 3 4.167,2.667 4.625,2.865 0.458,0.198 10 false x 3 4.76,0.104 5.219,0.302 0.458,0.198 10 false x 3 6.896,1.781 7.156,1.958 0.26,0.177 10 false x 3 4.344,3.021 6.177,3.219 1.833,0.198 8 false 29 (296, 21) 2.76,1.854 4.594,2.052 1.833,0.198 8 false 29 (296, 21) 2.427,0.438 2.979,0.792 0.552,0.354 18 false 5 5.448,2.302 6,2.656 0.552,0.354 18 false 6 5.781,0.469 6.333,0.823 0.552,0.354 18 false 7 5.646,1.156 6.198,1.51 0.552,0.354 18 false 8

Procedure Part Name Code
Z101186

Z101188

Z101187

5 FRAME UNDER COVER ASSEMBLY RH 51430A - - -
6 FRAME UNDER COVER ASSEMBLY LH 51450C - - -
7 FRONT FENDER APRON TRIM PACKING C 53784 - - -
8 FRONT FENDER APRON TRIM PACKING D 53785B - - -
9 FRONT WHEEL - - - -
10 PERFORM INITIALIZATION - - - (Click here)

V100146

N*m (kgf*cm, ft.*lbf): Specified torque * For use with SST

CAUTION / NOTICE / HINT

PROCEDURE

Hide 89467E 1.INSTALL NO. 4 AIR FUEL RATIO SENSOR

a.
A486419C01
2.156,1.385 2.156,0.958 true 5.844,0.417 5.635,0.521 5.635,0.521 5.938,0.76 true 0.406,0.083 0.688,0.438 0.281,0.354 18 false i 4.469,0.479 5.313,0.906 0.844,0.427 18 false ii 0.865,0.719 1.052,0.906 0.188,0.188 10 true *a 5.448,0.448 5.615,0.646 0.167,0.198 10 true *b 2.01,1.385 2.354,1.573 0.344,0.188 10 true SST 4.802,1.427 5.01,1.719 0.208,0.292 18 true iii
*a Torque Wrench Fulcrum Length *b Wire Harness Clamp


i.

Using SST, install the No. 4 air fuel ratio sensor to the converter with catalyst assembly RH.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the No. 4 air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)




ii.

Attach the 2 wire harness clamps.


iii.

Connect the No. 4 air fuel ratio sensor connector.



Hide 89467D 2.INSTALL NO. 3 AIR FUEL RATIO SENSOR

a.
A486418C02
1.99,1.583 1.99,1.156 true 6.01,0.521 5.635,0.365 5.635,0.365 5.75,0.531 true 0.406,0.083 0.688,0.438 0.281,0.354 18 false i 4.448,0.667 5.292,1.094 0.844,0.427 18 false ii 3.073,0.958 3.26,1.146 0.188,0.188 10 true *a 5.448,0.281 5.615,0.479 0.167,0.198 10 true *b 1.854,1.583 2.198,1.771 0.344,0.188 10 true SST 6.635,1.271 6.875,1.552 0.24,0.281 18 true iii
*a Torque Wrench Fulcrum Length *b Wire Harness Clamp


i.

Using SST, install the No. 3 air fuel ratio sensor to the converter with catalyst assembly LH.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the No. 3 air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)




ii.

Attach the 2 wire harness clamps.


iii.

Connect the No. 3 air fuel ratio sensor connector.



Hide 89467C 3.INSTALL NO. 2 AIR FUEL RATIO SENSOR

a.
A486421C01
0.99,1.313 1.344,1.313 true 1.927,0.521 2.125,0.677 0.198,0.156 10 true *a 0.656,1.26 0.979,1.417 0.323,0.156 10 true SST 0.458,0.073 0.74,0.427 0.281,0.354 18 false i 3.656,0.052 4.156,0.323 0.5,0.271 18 true ii, iii
*a Torque Wrench Fulcrum Length - -


i.

Using SST, install the No. 2 air fuel ratio sensor to the converter with catalyst assembly RH.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the No. 2 air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)




ii.

Attach the 4 wire harness clamps.


iii.

Connect the No. 2 air fuel ratio sensor connector.



Hide 89467B 4.INSTALL AIR FUEL RATIO SENSOR

a.
A486420C01
1.49,0.781 1.656,0.781 1.656,0.781 1.854,1.052 true 0.375,0.083 0.656,0.438 0.281,0.354 18 false i 3.698,0.094 4.188,0.385 0.49,0.292 18 true ii, iii 2.396,0.406 2.573,0.573 0.177,0.167 10 true *a 1.177,0.719 1.49,0.896 0.313,0.177 10 true SST
*a Torque Wrench Fulcrum Length - -


i.

Using SST, install the air fuel ratio sensor to the converter with catalyst assembly LH.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)




ii.

Attach the wire harness clamp.


iii.

Connect the air fuel ratio sensor connector.



Hide 51430A 5.INSTALL FRAME UNDER COVER ASSEMBLY RH

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

Hide 51450C 6.INSTALL FRAME UNDER COVER ASSEMBLY LH

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

Hide 53784 7.INSTALL FRONT FENDER APRON TRIM PACKING C

Hide 53785B 8.INSTALL FRONT FENDER APRON TRIM PACKING D

Hide 9.INSTALL FRONT WHEEL

Hide 10.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION