Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › ECM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0467381 ECM A

1GR-FE ENGINE CONTROL  ECM  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A486890N01
6.167,0.698 6.75,0.698 false 6.198,0.302 6.781,0.302 false 1.75,0.927 2.646,0.927 true 3,1.917 3.583,1.917 true 4.698,1.49 4.917,1.635 4.917,1.635 5.156,1.635 true 4.969,4.865 5.25,5.219 0.281,0.354 18 false 1 6.031,0.177 6.313,0.531 0.281,0.354 18 false 1 6.01,0.563 6.292,0.917 0.281,0.354 18 false 2 1.521,0.802 1.802,1.156 0.281,0.354 18 false 3 2.823,1.792 3.104,2.146 0.281,0.354 18 false 4 5.229,1.552 5.51,1.906 0.281,0.354 18 false 5 5.052,0.677 5.333,1.031 0.281,0.354 10 false x 2 4.188,1.75 4.469,2.104 0.281,0.354 10 false x 2 5.198,1.333 5.479,1.688 0.281,0.354 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
3 ECM 89661A (Click here) - -
4 NO. 1 ECM BRACKET 89667E - - -
5 NO. 2 ECM BRACKET 89668 - - -

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ECM removal/installation are shown below.

CAUTION / NOTICE / HINT

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Replacement of ECM Perform Vehicle Identification Number (VIN) registration DTC P063051 is output (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 89661A 3.REMOVE ECM

a.
A486891N02
0.438,0.104 0.719,0.458 0.281,0.354 18 false i 4,0.094 4.281,0.448 0.281,0.354 18 false ii 1.969,2.26 2.25,2.615 0.281,0.354 18 false iii

i.

Rotate the 2 levers while pushing the locks, and disconnect the 2 ECM connectors.

NOTICE:

After disconnecting the ECM connectors, make sure that dirt, water and other foreign matter does not contact the connecting parts of the ECM connectors.



ii.

Detach the 3 clamps.


iii.

Remove the 3 bolts and ECM.

NOTICE:

If the ECM has been struck or dropped, replace it.




Hide 89667E 4.REMOVE NO. 1 ECM BRACKET

a.
A486892


Hide 89668 5.REMOVE NO. 2 ECM BRACKET

a.
A486893