Home › Drivetrain › JF2BM (TRANSFER / 4WD / AWD) › 4WD CONTROL ECU (for RHD)
RM38G0E _52 Drivetrain _100437 JF2BM TRANSFER / 4WD / AWD _0467434 4WD CONTROL ECU(for RHD) A

JF2BM TRANSFER / 4WD / AWD  4WD CONTROL ECU(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C453535N03
4.729,4.76 5.354,4.76 false 2.521,4.615 2.99,4.615 false 2.771,4.167 3.031,4.375 0.26,0.208 10 false x 2 5.406,4.615 5.656,4.969 0.25,0.354 18 false 1 3.375,4.49 3.604,4.802 0.229,0.313 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PARKING ASSIST ECU 86792C - - -
2 4 WHEEL DRIVE CONTROL ECU 89533 (Click here) - -

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the 4 wheel drive control ECU removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)
4 wheel drive control ECU Update ECU security key Vehicle control history (RoB) are stored (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 89533 2.REMOVE 4 WHEEL DRIVE CONTROL ECU

a.
C453536C01
3.646,2.188 5.229,2.188 true 0.271,0.063 0.458,0.438 0.188,0.375 18 false i 3.719,0.094 3.906,0.469 0.188,0.375 18 false ii 1.906,2.083 2.146,2.406 0.24,0.323 18 false iii 5.271,2.094 5.531,2.344 0.26,0.25 10 false *a
*a Hole on Top of Vehicle - -
V113147

Slide Upward
V113148

Remove


i.

Disconnect the 4 connectors.


ii.

Remove the 2 bolts.


iii.

Slide the 4 wheel drive control ECU upward and remove.

HINT:

Pass the claw of the bracket through the hole on the top of the vehicle.