Home › Drivetrain › JF2BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM
RM38G0E _52 Drivetrain _100437 JF2BM TRANSFER / 4WD / AWD _0467431 TRANSFER SYSTEM J

JF2BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  Center Differential Lock Switch Circuit  


WIRING DIAGRAM

C339930E16
0.573,2.438 0.979,2.635 0.406,0.198 10 false I85 0.635,1.833 0.833,2.031 0.198,0.198 10 false 1 0.917,1.854 1.375,2.031 0.458,0.177 10 false GND2 2.063,1.854 2.521,2.052 0.458,0.198 10 false CPU 2.458,1.844 2.75,2.042 0.292,0.198 10 false 7 3.417,1.865 3.729,2.063 0.313,0.198 10 false 12 3.688,1.865 4,2.063 0.313,0.198 10 false DL 3.604,2.698 4.063,2.896 0.458,0.198 10 false B9 3.635,2.917 5.302,3.24 1.667,0.323 10 false 4 Wheel Drive Control ECU 5.74,2.74 7,3.167 1.26,0.427 10 false Combination Meter Assembly 4.438,0.979 4.75,1.177 0.313,0.198 10 false IG 0.865,3.385 2.656,3.625 1.792,0.24 10 false : CAN Communication Line 0.552,2.635 2.469,3.323 1.917,0.688 10 false Center Differential Lock Switch (Transfer Position Switch)

PROCEDURE

1.CHECK CENTER DIFFERENTIAL LOCK INDICATOR LIGHT
a.

Turn the ignition switch to ON.


b.

Check the center differential lock indicator light.


c.

Press the center differential lock switch.


d.

After 60 seconds, check the center differential lock indicator light.

Result:
Result Proceed to

Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

The center differential lock indicator light blinks, turns off or illuminates A
Center differential lock indicator light remains off regardless of switch operation B
Center differential lock indicator remains illuminated regardless of switch operation C




A

END

B

2.CHECK CAN COMMUNICATION LINE

C

7.CHECK CAN COMMUNICATION LINE
2.CHECK CAN COMMUNICATION LINE
a.

Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus.

CAN Bus Check
50007
OK:

"Bus Check" indicates no malfunctions in CAN communication.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (CENTER DIFFERENTIAL LOCK CONTROL SWITCH)

NG

3.READ VALUE USING GTS (CENTER DIFFERENTIAL LOCK CONTROL SWITCH)
a.

Turn the ignition switch to ON.


b.

According to the display on the GTS, read the Data List.

Powertrain > Four Wheel Drive > Data List
Tester Display
Center Differential Lock Control Switch
50003 442 18
Powertrain > Four Wheel Drive > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Center Differential Lock Control Switch Center differential lock switch (transfer position switch) status OFF or ON OFF: Not pressed
ON: Pressed and held
-
OK:

Display changes according to center differential lock switch (transfer position switch) operation.



c.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

4.INSPECT COMBINATION METER ASSEMBLY

NG

5.INSPECT CENTER DIFFERENTIAL LOCK SWITCH (TRANSFER POSITION SWITCH)
4.INSPECT COMBINATION METER ASSEMBLY
a.

Using the GTS, perform the Active Test "Center DIFF LOCK Indicator" of the combination meter assembly.

Body Electrical > Combination Meter > Active Test
Tester Display
Center DIFF LOCK Indicator
50004 409 98
OK:

The center differential lock indicator light illuminates or turns off in accordance with the operation.



Result:
Proceed to
OK
NG



OK

NG

5.INSPECT CENTER DIFFERENTIAL LOCK SWITCH (TRANSFER POSITION SWITCH)
a.

Inspect the center differential lock switch (transfer position switch).

Click hereDrivetrain>JF2BM (TRANSFER / 4WD / AWD)>CENTER DIFFERENTIAL LOCK SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - CENTER DIFFERENTIAL LOCK SWITCH (TRANSFER POSITION SWITCH))

NG

REPLACE CENTER DIFFERENTIAL LOCK SWITCH (TRANSFER POSITION SWITCH)

6.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - CENTER DIFFERENTIAL LOCK SWITCH (TRANSFER POSITION SWITCH))
a.

Disconnect the B9 4 wheel drive control ECU connector.


b.

Disconnect the I85 center differential lock switch (transfer position switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B9,I85)Location & Routing

Click Connector(B9)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECU

Click Connector(I85)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Transfer Position Switch

B9-12 (DL) - I85-7 (CPU) Always Below 1 Ω
I85-1 (GND2) - Body ground Always Below 1 Ω
B9-12 (DL) or I85-7 (CPU) - Body ground Always 10 kΩ or higher



d.

Connect the I85 center differential lock switch (transfer position switch) connector.


e.

Connect the B9 4 wheel drive control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK CAN COMMUNICATION LINE
a.

Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus.

CAN Bus Check
50007
OK:

"Bus Check" indicates no malfunctions in CAN communication.



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (CENTER DIFFERENTIAL LOCK INDICATOR REQUEST)

NG

8.READ VALUE USING GTS (CENTER DIFFERENTIAL LOCK INDICATOR REQUEST)
a.

Turn the ignition switch to ON.


b.

According to the display on the GTS, read the Data List.

i.

Turn the center differential lock switch (transfer position switch) on and off several times and check the GTS display condition of the center differential lock indicator light.

Powertrain > Four Wheel Drive > Data List
Tester Display
Center Differential Lock Indicator Request
50003 442 40
Powertrain > Four Wheel Drive > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Center Differential Lock Indicator Request Center differential lock indicator light request OFF, ON, Blink1, Blink2 or Blink3 OFF: Indicator light turns off
ON: Indicator light illuminates
Blink1: Indicator light blinks
Blink2: Indicator light blinks 3 times
Blink3: Indicator light rapidly blinks
·

Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

·

Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off)




Result:
Result Proceed to
Data List continues to display ON even when center differential lock switch (transfer position switch) is operated A
Data List display changes according to center differential lock switch (transfer position switch) operation B



A

B