Home › Drivetrain › JF2BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM
RM38G0E _52 Drivetrain _100437 JF2BM TRANSFER / 4WD / AWD _0467431 TRANSFER SYSTEM J

JF2BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  4WD Control Switch Circuit  


WIRING DIAGRAM

C420980E05
5.833,2.188 7.01,2.563 1.177,0.375 10 false Combination Meter Assembly 3.875,2.427 5.583,2.792 1.708,0.365 10 false 4 Wheel Drive Control ECU 3.854,2.208 5.563,2.573 1.708,0.365 10 false B9 0.594,2.135 2.948,2.521 2.354,0.385 10 false Transfer Position Switch 0.583,1.917 0.99,2.125 0.406,0.208 10 false I85 1.208,0.885 2.917,1.25 1.708,0.365 10 false H4 0.646,1.031 1.156,1.24 0.51,0.208 10 false ECU 3.948,1.333 5.656,1.698 1.708,0.365 10 false LO 2.854,1.333 3.177,1.521 0.323,0.188 10 false 8 0.417,1.031 0.625,1.229 0.208,0.198 10 false 2 2.365,1.333 2.771,1.542 0.406,0.208 10 false 2WD 3.667,1.333 3.896,1.542 0.229,0.208 10 false 11 4.604,0.667 4.979,0.875 0.375,0.208 10 false IGR 0.479,3.135 2.188,3.5 1.708,0.365 10 false : CAN Communication Line 1.531,1.281 1.844,1.479 0.313,0.198 10 false L4

PROCEDURE

1.CONFIRM PROBLEM SYMPTOM
a.

Confirm the problem symptoms.

Result:
Result Proceed to
The 4LO indicator light remains off after operating the transfer position switch to L4 A
The 4LO indicator light remains on after operating the transfer position switch to H4 B




A

2.CHECK 4LO INDICATOR LIGHT

B

8.CHECK 4LO INDICATOR LIGHT
2.CHECK 4LO INDICATOR LIGHT
HINT:

Perform the following procedure with the vehicle stopped.


a.

Turn the ignition switch to ON.


b.

Move the shift lever to N.


c.

Turn the transfer position switch to L4.


d.

Check the 4LO indicator light.

Result:
Result Proceed to

Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

The 4LO indicator light remains off A
The 4LO indicator light is blinking or illuminated B



e.

Turn the ignition switch off.



A

3.CHECK CAN COMMUNICATION LINE

B

END

3.CHECK CAN COMMUNICATION LINE
a.

Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus.

CAN Bus Check
50007
OK:

"Bus Check" indicates no malfunctions in CAN communication.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (H-L SHIFT SWITCH)

NG

4.READ VALUE USING GTS (H-L SHIFT SWITCH)
a.

Turn the ignition switch to ON.


b.

According to the display on the GTS, read the Data List.

Powertrain > Four Wheel Drive > Data List
Tester Display
H-L Shift Switch
50003 442 17
Powertrain > Four Wheel Drive > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
H-L Shift Switch Transfer position switch status OFF or ON OFF: H4
ON: L4
-
OK:

Display changes according to transfer position switch operation.



c.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

5.INSPECT COMBINATION METER ASSEMBLY (4LO INDICATOR)

NG

6.INSPECT TRANSFER POSITION SWITCH
5.INSPECT COMBINATION METER ASSEMBLY (4LO INDICATOR)
a.

Using the GTS, perform the Active Test "4LO Indicator" of the combination meter assembly.

Body Electrical > Combination Meter > Active Test
Tester Display
4LO Indicator
50004 409 101
OK:

The 4LO indicator light turns on or off in accordance with the GTS.



Result:
Proceed to
OK
NG



OK

NG

6.INSPECT TRANSFER POSITION SWITCH
a.

Inspect the transfer position switch.

Click hereDrivetrain>JF2BM (TRANSFER / 4WD / AWD)>4WD CONTROL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER POSITION SWITCH)

NG

REPLACE TRANSFER POSITION SWITCH

7.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER POSITION SWITCH)
a.

Disconnect the B9 4 wheel drive control ECU connector.


b.

Disconnect the I85 transfer position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B9,I85)Location & Routing

Click Connector(B9)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECU

Click Connector(I85)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Transfer Position Switch

B9-11 (LO) - I85-8 (2WD) Always Below 1 Ω
B9-11 (LO) or I85-8 (2WD) - Body ground Always 10 kΩ or higher
I85-2 (ECU) - Body ground Always Below 1 Ω



d.

Connect the I85 transfer position switch connector.


e.

Connect the B9 4 wheel drive control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK 4LO INDICATOR LIGHT
HINT:

Perform the following procedure with the vehicle stopped.


a.

Turn the ignition switch to ON.


b.

Move the shift lever to N.


c.

Turn the transfer position switch to L4.


d.

Check the 4LO indicator light.

Result:
Result Proceed to

Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

The 4LO indicator light remains illuminated A
The 4LO indicator light is blinking or illuminated B



e.

Turn the ignition switch off.



A

9.CHECK CAN COMMUNICATION LINE

B

END

9.CHECK CAN COMMUNICATION LINE
a.

Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus.

CAN Bus Check
50007

OK:

"Bus Check" indicates no malfunctions in CAN communication.


Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS (L4 INDICATOR REQUEST)

NG

10.READ VALUE USING GTS (L4 INDICATOR REQUEST)
a.

Turn the ignition switch to ON.


b.

According to the display on the GTS, read the Data List.

Powertrain > Four Wheel Drive > Data List
Tester Display
L4 Indicator Request
50003 442 39
Powertrain > Four Wheel Drive > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L4 Indicator Request 4LO indicator light request OFF, ON, Blink1, Blink2 or Blink3 OFF: Indicator light turns off
ON: Indicator light illuminates
Blink1: Indicator light blinks
Blink2: Indicator light blinks 3 times
Blink3: Indicator light rapidly blinks
·

Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

·

Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off)


i.

Operate the transfer position switch several times between H4 and L4, and then check the GTS display condition of the 4LO indicator light.

Result:
Result Proceed to
Data List continues to display ON even when transfer position switch is operated A
Data List display changes according to transfer position switch operation B





A

B