Home › Drivetrain › JF2BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM
RM38G0E _52 Drivetrain _100437 JF2BM TRANSFER / 4WD / AWD _0467431 TRANSFER SYSTEM C

JF2BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  P17B81C  4WD/AWD Front Differential Unit Actuator "A" Control Circuit Circuit Voltage Out of Range  P17B949  4WD/AWD Differential Unit Actuator Control Module Internal Electronic Failure  P17C21C  4WD/AWD Rear Differential Unit Actuator "A" Control Circuit Circuit Voltage Out of Range  P17F328  4WD/AWD Front Differential Unit Actuator "A" Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure  P17F428  4WD/AWD Rear Differential Unit Actuator "A" Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure  P17F928  4WD/AWD Transfer Case Shift Motor Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P17B81C 4WD/AWD Front Differential Unit Actuator "A" Control Circuit Circuit Voltage Out of Range
Diagnosis Condition:
·

When checking front differential lock solenoid drive circuit with 4 wheel drive control ECU started

·

When checking front differential lock solenoid drive circuit prior to front differential lock operation starting


Malfunction Status:
·

Front differential lock solenoid drive circuit monitor voltage is malfunction detection maximum voltage or less, and front differential lock solenoid drive circuit monitor voltage is malfunction detection minimum voltage or higher


Malfunction Time:
·

1 second or more


Number of Trips:
·

1 trip


4 wheel drive control ECU Four Wheel Drive
P17B949 4WD/AWD Differential Unit Actuator Control Module Internal Electronic Failure
Diagnosis Condition:
·

IPD operating


Malfunction Status:
·

IPD malfunction detected


Malfunction Time:
·

1 second or more


Number of Trips:
·

1 trip


IPD: Abbreviation for Intelligent Power Device
4 wheel drive control ECU Four Wheel Drive
P17C21C 4WD/AWD Rear Differential Unit Actuator "A" Control Circuit Circuit Voltage Out of Range
Diagnosis Condition:
·

When checking rear differential lock solenoid drive circuit with ECU started

·

When checking rear differential lock solenoid drive circuit prior to rear differential lock operation starting


Malfunction Status:
·

Solenoid drive circuit monitor voltage is malfunction detection maximum voltage or less, and solenoid drive circuit monitor voltage is malfunction detection minimum voltage or higher


Malfunction Time:
·

1 second or more


Number of Trips:
·

1 trip


4 wheel drive control ECU Four Wheel Drive
P17F328 4WD/AWD Front Differential Unit Actuator "A" Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure
Diagnosis Condition:
·

When checking front differential lock solenoid drive circuit with 4 wheel drive control ECU started

·

When checking front differential lock solenoid drive circuit prior to front differential lock operation starting


Malfunction Status:
·

Front differential lock solenoid drive circuit monitor current is outside range from 2.973 to 4.412 A


Malfunction Time:
·

1 second or more


Number of Trips:
·

1 trip


4 wheel drive control ECU Four Wheel Drive
P17F428 4WD/AWD Rear Differential Unit Actuator "A" Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure
Diagnosis Condition:
·

When checking rear differential lock solenoid drive circuit with ECU started

·

When checking rear differential lock solenoid drive circuit prior to rear differential lock operation starting


Malfunction Status:
·

Solenoid drive circuit monitor current is outside range from 2.973 to 4.412 A


Malfunction Time:
·

1 second or more


Number of Trips:
·

1 trip


4 wheel drive control ECU Four Wheel Drive
P17F928 4WD/AWD Transfer Case Shift Motor Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure
Diagnosis Condition:
·

When starting high-low transfer shift motor operation


Malfunction Status:
·

Motor drive circuit monitor current is outside range of -3.0 to 3.0 A


Malfunction Time:
·

1 second or more


Number of Trips:
·

1 trip


4 wheel drive control ECU Four Wheel Drive

DTC Detection Conditions: P17B81C
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When checking front differential lock solenoid drive circuit with 4 wheel drive control ECU started ○ -
When checking front differential lock solenoid drive circuit prior to front differential lock operation starting - ○
Malfunction Status Front differential lock solenoid drive circuit monitor voltage is malfunction detection maximum voltage or less, and front differential lock solenoid drive circuit monitor voltage is malfunction detection minimum voltage or higher ○ ○
Detection Time 1 second or more 1 second or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: P17C21C
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When checking rear differential lock solenoid drive circuit with ECU started ○ -
When checking rear differential lock solenoid drive circuit prior to rear differential lock operation starting - ○
Malfunction Status Solenoid drive circuit monitor voltage is malfunction detection maximum voltage or less, and solenoid drive circuit monitor voltage is malfunction detection minimum voltage or higher ○ ○
Detection Time 1 second or more 1 second or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: P17F328
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When checking front differential lock solenoid drive circuit with 4 wheel drive control ECU started ○ -
When checking front differential lock solenoid drive circuit prior to front differential lock operation starting - ○
Malfunction Status Front differential lock solenoid drive circuit monitor current is outside range from 2.973 to 4.412 A ○ ○
Detection Time 1 second or more 1 second or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: P17F428
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When checking rear differential lock solenoid drive circuit with ECU started ○ -
When checking rear differential lock solenoid drive circuit prior to rear differential lock operation starting - ○
Malfunction Status Solenoid drive circuit monitor current is outside range from 2.973 to 4.412 A ○ ○
Detection Time 1 second or more 1 second or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


PROCEDURE

1.CLEAR DTC
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Four Wheel Drive > Clear DTCs
50002 442

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

2.CHECK DTC OUTPUT
2.CHECK DTC OUTPUT
a.

Turn the ignition switch to ON.


b.

Check for DTCs.

Powertrain > Four Wheel Drive > Trouble Codes
50001 442

Result:
Result Proceed to
P17B81C, P17B949, P17C21C, P17F328, P17F428 or P17F928 is output A
P17B81C, P17B949, P17C21C, P17F328, P17F428 and P17F928 are not output B


c.

Turn the ignition switch off.



A

B