Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467506 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Back Door Entry Lock and Unlock Functions do not Operate  


DESCRIPTION

If the entry lock and unlock functions do not operate for the back door only, the request code may not be being transmitted from the back door. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and electrical key and tire pressure warning ECU and receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage compartment)) or there may be wave interference.

WIRING DIAGRAM

B506721E23
0.771,2.76 2.802,3.26 2.031,0.5 10 false Electrical Key Antenna (Outside Luggage Compartment) 0.76,4.938 2.875,5.563 2.115,0.625 10 false License Plate Light Assembly with Back Door Opener Switch 5.031,5.51 6.854,5.917 1.823,0.406 10 false Certification ECU (Smart Key ECU Assembly) 0.771,2.615 1.208,2.833 0.438,0.219 10 false Q32 0.75,4.74 1.781,5.01 1.031,0.271 10 false g3 1.573,0.865 2.146,1.135 0.573,0.271 10 false ANTE8 1.646,2.021 2.219,2.292 0.573,0.271 10 false CLGB 2.115,2.01 2.688,2.281 0.573,0.271 10 false 1 0.813,4.281 1.385,4.552 0.573,0.271 10 false 4 5.01,0.844 5.583,1.115 0.573,0.271 10 false 4 5.021,5.323 5.594,5.594 0.573,0.271 10 false I38 5.01,2 5.583,2.271 0.573,0.271 10 false 3 4.969,3.76 5.542,4.031 0.573,0.271 10 false 16 4.969,4.281 5.542,4.552 0.573,0.271 10 false 17 2.073,3.76 2.646,4.031 0.573,0.271 10 false UL 2.146,4.281 2.719,4.552 0.573,0.271 10 false L 1.031,4.292 1.604,4.563 0.573,0.271 10 false E 2.115,0.875 2.688,1.146 0.573,0.271 10 false 2 2.323,3.76 2.896,4.031 0.573,0.271 10 false 3 2.323,4.271 2.896,4.542 0.573,0.271 10 false 5 5.24,4.281 5.813,4.552 0.573,0.271 10 false TSW6 5.229,3.76 5.802,4.031 0.573,0.271 10 false TSW5 5.25,0.875 5.823,1.146 0.573,0.271 10 false CLG8 5.25,2.042 5.823,2.313 0.573,0.271 10 false CG8B 6.052,1.542 6.625,1.813 0.573,0.271 10 false IC 5.917,3.594 6.49,3.865 0.573,0.271 10 false 5 V 5.604,3.052 6.177,3.323 0.573,0.271 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

After repair, confirm that no DTCs are output.



HINT:
·

If the back door entry lock and unlock function does not operate, the cause of the malfunction may be stored in the certification ECU (smart key ECU assembly).

·

If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether the malfunction was caused by wave interference.



Body Electrical > Entry&Start > Utility
Tester Display
Vehicle Control History (RoB)
50005 440 62

PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the back door lock and unlock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Back door lock/unlock operate normally.



Result:
Proceed to
OK
NG



OK

2.CHECK WAVE ENVIRONMENT

NG

2.CHECK WAVE ENVIRONMENT
a.
B581611C01
1.781,1.229 2.01,1.479 0.229,0.25 10 false *a 1.656,1.76 1.885,2.01 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a Approximately 0.3 m (0.984 ft.)

The illustrations shown are examples only.


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the electrical key antenna (outside luggage compartment) and perform an entry back door open/lock function check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK

HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the electrical key antenna (outside luggage compartment).

·

When the electrical key transmitter sub-assembly is brought near the electrical key antenna (outside luggage compartment), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.




Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

3.READ VALUE USING GTS (TRUNK LID/BACK DOOR LOCK SWITCH, TRUNK LID/BACK DOOR UNLOCK SWITCH)

B

AFFECTED BY WAVE INTERFERENCE

3.READ VALUE USING GTS (TRUNK LID/BACK DOOR LOCK SWITCH, TRUNK LID/BACK DOOR UNLOCK SWITCH)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Trunk Lid/Back Door Lock Switch License plate light assembly with back door opener switch (lock switch) OFF or ON OFF: License plate light assembly with back door opener switch (lock switch) not pressed
ON: License plate light assembly with back door opener switch (lock switch) pressed
·

Displays whether the license plate light assembly with back door opener switch (lock switch) is on or off.

·

Use this Data List item to help determine if there is a switch malfunction when the back door lock function does not operate.


Trunk Lid/Back Door Unlock Switch License plate light assembly with back door opener switch (open switch) OFF or ON OFF: License plate light assembly with back door opener switch (open switch) not pressed
ON: License plate light assembly with back door opener switch (open switch) pressed
·

Displays whether the license plate light assembly with back door opener switch (unlock switch) is on or off.

·

Use this Data List item to help determine if there is a switch malfunction when the entry back door open function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Trunk Lid/Back Door Lock Switch
Trunk Lid/Back Door Unlock Switch
50003 440 13,14
OK:

The GTS display changes correctly in response to the operation of the license plate light assembly with back door opener switch.



Result:
Proceed to
OK
NG



OK

4.CHECK KEY DIAGNOSTIC MODE

NG

8.CHECK HARNESS AND CONNECTOR (LICENSE PLATE LIGHT ASSEMBLY WITH BACK DOOR OPENER SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
4.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antenna in key diagnostic mode.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 440 2541

b.
B581611C01
1.781,1.229 2.01,1.479 0.229,0.25 10 false *a 1.656,1.76 1.885,2.01 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

i.

Check the electrical key antenna (outside luggage compartment):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage compartment), check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.





Result:
Result Proceed to
Wireless buzzer does not sound A
Wireless buzzer sounds B



A

5.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the I38 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the Q32 electrical key antenna (outside luggage compartment) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I38,Q32)Location & Routing

Click Connector(I38)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(Q32)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Electrical Key Antenna

I38-4 (CLG8) - Q32-2 (ANTE8) Always Below 1 Ω
I38-3 (CG8B) - Q32-1 (CLGB) Always Below 1 Ω
I38-4 (CLG8) or Q32-2 (ANTE8) - Other terminals and body ground Always 10 kΩ or higher
I38-3 (CG8B) or Q32-1 (CLGB) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the I38 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

6.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))
a.
B596320C01
0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 0.229,1.063 0.646,1.354 0.417,0.292 10 false GND
*a Waveform 1


Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(Q32)Location & Routing

Click Connector(Q32)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Electrical Key Antenna

Q32-1 (CLGB) - Q32-2 (ANTE8) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

License plate light assembly with back door opener switch off → on


5 V/DIV., 50 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

NG

7.CHECK ENTRY OPERATION
7.CHECK ENTRY OPERATION
a.

Connect all connectors and check that the function operates normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function operates normally A
Entry function does not operate normally B



A

END (CONNECTOR WAS NOT CONNECTED SECURELY)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

8.CHECK HARNESS AND CONNECTOR (LICENSE PLATE LIGHT ASSEMBLY WITH BACK DOOR OPENER SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
a.

Disconnect the I38 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the g3 license plate light assembly with back door opener switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I38,g3)Location & Routing

Click Connector(I38)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(g3)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>License Plate Light Assembly with Back Door Opener Switch

I38-16 (TSW5) - g3-3 (UL) Always Below 1 Ω
I38-17 (TSW6) - g3-5 (L) Always Below 1 Ω
g3-4 (E) - Other terminals and body ground Always Below 1 Ω
I38-16 (TSW5) or g3-3 (UL) - Other terminals and body ground Always 10 kΩ or higher
I38-17 (TSW6) or g3-5 (L) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT LICENSE PLATE LIGHT ASSEMBLY WITH BACK DOOR OPENER SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT LICENSE PLATE LIGHT ASSEMBLY WITH BACK DOOR OPENER SWITCH

OK

10.CHECK ENTRY OPERATION

NG

REPLACE LICENSE PLATE LIGHT ASSEMBLY WITH BACK DOOR OPENER SWITCH

10.CHECK ENTRY OPERATION
a.

Connect all connectors and check that the function operates normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function operates normally A
Entry function does not operate normally B



A

END (CONNECTOR WAS NOT CONNECTED SECURELY)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)