Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467506 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  All Door Entry Lock/Unlock Functions do not Operate, but Wireless Functions Operate  


DESCRIPTION

When the wireless operation can be used to lock and unlock the doors, communication between the electrical key and tire pressure warning ECU and receiver and certification ECU (smart key ECU assembly) is normal. If the entry lock and unlock functions do not operate, the entry cancel function may be set through the customize function, there may be communication problems between the electrical key transmitter sub-assembly and vehicle, or there may be wave interference.

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to Service Bulletin.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

After repair, confirm that no DTCs are output.

·

Before performing the inspection, check that DTC B124296 (wireless door lock control) is not output.



PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless function operates normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally B



A

2.CHECK ENTRY OPERATION

B

2.CHECK ENTRY OPERATION
a.

Check the operation of the entry lock and unlock functions.

i.
for LHD:
B581631C01
1.083,0.5 1.5,0.5 1.5,0.5 2,1.5 false 0.896,0.438 1.208,0.635 0.313,0.198 10 false *a
*a Unlock Sensor (Backside)

The illustrations shown are examples only.


for RHD:
B581630C01
1.688,1.469 2.25,0.667 2.25,0.667 2.667,0.667 false 2.719,0.615 3.031,0.813 0.313,0.198 10 false *a
*a Unlock Sensor (Backside)

The illustrations shown are examples only.


Check the entry unlock function.

1.

Turn the ignition switch off.

2.

Open and close the driver door.

3.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.

4.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.

5.

Check that the LED of the electrical key transmitter sub-assembly blinks.

6.

Touch the unlock sensor on the backside of the front door outside handle assembly (for driver door) for 2 seconds or more.


*: Perform this step 3 seconds or more after performing step (3).


HINT:
·

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (1).

·

Inspect the front passenger door, rear door LH* and rear door RH* using the same procedure.

*: w/ Rear Door Entry Function





ii.
for LHD:
B581605C01
2.219,1.083 2.531,1.281 0.313,0.198 10 false *a 2.063,1.625 2.375,1.823 0.313,0.198 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.3 m (0.984 ft.)

The illustrations shown are examples only.


for RHD:
B581614C01
1.385,1.083 1.615,1.333 0.229,0.25 10 false *a 1.25,1.615 1.479,1.865 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.3 m (0.984 ft.)

The illustrations shown are examples only.


Check the entry lock function.

1.

Turn the ignition switch off.

2.

Open and close the driver door.

3.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.

4.

Touch the lock sensor of the front door outside handle assembly (groove on the front door outside handle) with 2 or more fingers for 2 seconds or more.

HINT:
·

If the door does not lock even when touching the lock sensor for 2 seconds or more, touch it with your palm.

·

When checking the operation of the lock sensor again, make sure to perform the procedure from step (1).

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.

·

Inspect the front passenger door, rear door LH* and rear door RH* using the same procedure.

*: w/ Rear Door Entry Function






iii.
B581606C01
1.667,2.667 1.917,2.333 1.917,2.333 2.167,2.333 false 1.667,1.802 1.979,2 0.313,0.198 10 false *1 1.781,1.302 2.094,1.5 0.313,0.198 10 false *a 2.198,2.271 2.51,2.469 0.313,0.198 10 false *2
*1 Electrical Key Transmitter Sub-assembly
*2 License Plate Light Assembly with Back Door Opener Switch (Open Switch)
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


Check the entry back door open function.

1.

With the back door closed and locked, press the open switch of the license plate light assembly with back door opener switch while carrying the electrical key transmitter sub-assembly and check that the back door opens.



iv.
B581607C01
1.719,2.667 1.969,2.333 1.969,2.333 2.219,2.333 false 1.667,1.802 1.979,2 0.313,0.198 10 false *1 1.781,1.302 2.094,1.5 0.313,0.198 10 false *a 2.25,2.271 2.563,2.469 0.313,0.198 10 false *2
*1 Electrical Key Transmitter Sub-assembly
*2 License Plate Light Assembly with Back Door Opener Switch (Lock Switch)
*a Approximately 0.3 m (0.984 ft.)

The illustrations shown are examples only.


Check the entry back door lock function.

1.

With the back door closed and unlocked, press the lock switch of the license plate light assembly with back door opener switch while carrying the electrical key transmitter sub-assembly outside of the vehicle and check that the back door locks.




Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

3.CHECK WAVE ENVIRONMENT

B

3.CHECK WAVE ENVIRONMENT
a.

Move the electrical key transmitter sub-assembly as described below and perform the operation inspection.

HINT:
·

When the electrical key transmitter sub-assembly is brought near the front door outside handle assembly (for driver door) or electrical key antenna (outside luggage compartment), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.

·

The transmitting wave of the wireless function and entry function are the same, but the wave logic is different. As a result, it is possible that only the wireless function or only the entry function is affected by wave interference.



i.
for LHD:
B581605C01
2.219,1.083 2.531,1.281 0.313,0.198 10 false *a 2.063,1.625 2.375,1.823 0.313,0.198 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


for RHD:
B581614C01
1.385,1.083 1.615,1.333 0.229,0.25 10 false *a 1.25,1.615 1.479,1.865 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for driver door) and perform a driver door entry lock and unlock operation check.

HINT:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the door handle.



ii.
for LHD:
B581614C01
1.385,1.083 1.615,1.333 0.229,0.25 10 false *a 1.25,1.615 1.479,1.865 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a Approximately 0.3 m (0.984 ft.)

The illustrations shown are examples only.


for RHD:
B581605C01
2.219,1.083 2.531,1.281 0.313,0.198 10 false *a 2.063,1.625 2.375,1.823 0.313,0.198 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a Approximately 0.3 m (0.984 ft.)

The illustrations shown are examples only.


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for front passenger door) and perform a front passenger door entry lock and unlock operation check.

HINT:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the door handle.



iii.
for LHD:
B581615C01
1.781,1.094 2.01,1.344 0.229,0.25 10 false *a 1.656,1.635 1.885,1.885 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a Approximately 0.3 m (0.984 ft.)

The illustrations shown are examples only.


for RHD:
B581616C01
1.781,1.094 2.01,1.344 0.229,0.25 10 false *a 1.656,1.635 1.885,1.885 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a Approximately 0.3 m (0.984 ft.)

The illustrations shown are examples only.


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the rear door outside handle assembly (for driver side) and perform a rear door (for driver side) entry lock and unlock operation check. (w/ Rear Door Entry Function)

HINT:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the door handle.



iv.
for LHD:
B581616C01
1.781,1.094 2.01,1.344 0.229,0.25 10 false *a 1.656,1.635 1.885,1.885 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a Approximately 0.3 m (0.984 ft.)

The illustrations shown are examples only.


for RHD:
B581615C01
1.781,1.094 2.01,1.344 0.229,0.25 10 false *a 1.656,1.635 1.885,1.885 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a Approximately 0.3 m (0.984 ft.)

The illustrations shown are examples only.


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the rear door outside handle assembly (for front passenger side) and perform a rear door (for front passenger side) entry lock and unlock operation check. (w/ Rear Door Entry Function)

HINT:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the door handle.



v.
B581611C01
1.781,1.229 2.01,1.479 0.229,0.25 10 false *a 1.656,1.76 1.885,2.01 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a Approximately 0.3 m (0.984 ft.)

The illustrations shown are examples only.


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the electrical key antenna (outside luggage compartment) and perform a back door open and lock function check.

HINT:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the rear bumper.




Result:
Result Proceed to
All operation checks fail A
All operation checks are normal B
Some operation checks are normal C



A

4.CHECK KEY DIAGNOSTIC MODE

B

AFFECTED BY WAVE INTERFERENCE

C

4.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antennas in key diagnostic mode.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 440 2541

b.

Select either channel 1 or channel 2 and perform key diagnostic mode inspection for each channel.

i.
for LHD:
B581605C01
2.219,1.083 2.531,1.281 0.313,0.198 10 false *a 2.063,1.625 2.375,1.823 0.313,0.198 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


for RHD:
B581614C01
1.385,1.083 1.615,1.333 0.229,0.25 10 false *a 1.25,1.615 1.479,1.865 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


Check the electrical key antenna (for driver door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




ii.
for LHD:
B581614C01
1.385,1.083 1.615,1.333 0.229,0.25 10 false *a 1.25,1.615 1.479,1.865 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


for RHD:
B581605C01
2.219,1.083 2.531,1.281 0.313,0.198 10 false *a 2.063,1.625 2.375,1.823 0.313,0.198 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


Check the electrical key antenna (for front passenger door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for front passenger door), check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




iii.
for LHD:
B581615C01
1.781,1.094 2.01,1.344 0.229,0.25 10 false *a 1.656,1.635 1.885,1.885 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


for RHD:
B581616C01
1.781,1.094 2.01,1.344 0.229,0.25 10 false *a 1.656,1.635 1.885,1.885 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


Check the electrical key antenna (for rear door (for driver side)): (w/ Rear Door Entry Function)

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the rear door outside handle assembly (for driver side), check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




iv.
for LHD:
B581616C01
1.781,1.094 2.01,1.344 0.229,0.25 10 false *a 1.656,1.635 1.885,1.885 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


for RHD:
B581615C01
1.781,1.094 2.01,1.344 0.229,0.25 10 false *a 1.656,1.635 1.885,1.885 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


Check the electrical key antenna (for rear door (for front passenger side)): (w/ Rear Door Entry Function)

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the rear door outside handle assembly (for front passenger side), check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




v.
B581611C01
1.781,1.229 2.01,1.479 0.229,0.25 10 false *a 1.656,1.76 1.885,2.01 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


Check the electrical key antenna (outside luggage compartment):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage compartment), check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.



OK:

Wireless buzzer sounds.




Result:
Result Proceed to
All diagnostic mode inspections fail A
Some diagnostic mode inspections fail (door) B
Some diagnostic mode inspections fail (outside luggage compartment) C
All diagnostic mode inspections are normal D



A

5.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

C

D

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.


Result:
Result Proceed to
Another registered electrical key transmitter sub-assembly is not available A
Another registered electrical key transmitter sub-assembly is available B



A

6.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

7.CHECK ENTRY OPERATION
6.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.CHECK ENTRY OPERATION
7.CHECK ENTRY OPERATION
a.

Using another registered electrical key transmitter sub-assembly, check that the entry function operates normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function operates normally A
Entry function does not operate normally B



A

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)