Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467506 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Rear Door LH Entry Unlock Function does not Operate  


DESCRIPTION

If the entry unlock function does not operate for the rear door LH only, but the entry lock function operates, the request code is being transmitted properly from the rear door LH. In this case, there may be a problem related to the unlock sensor (connection between the certification ECU (smart key ECU assembly) and rear door outside handle assembly (for driver side)).

WIRING DIAGRAM

for RHD:
B610733E12
0.323,2.708 3.219,3.26 2.896,0.552 10 false Rear Door Outside Handle Assembly LH 0.333,2.521 1.938,2.813 1.604,0.292 10 false P8 1.781,0.771 2.021,1.01 0.24,0.24 10 false 4 1.792,1.917 2.031,2.156 0.24,0.24 10 false 6 1.323,0.771 1.688,1 0.365,0.229 10 false ANT1 1.313,1.917 1.677,2.146 0.365,0.229 10 false ANT2 5.26,0.771 5.729,1.021 0.469,0.25 10 false CLG4 5.24,1.917 5.708,2.167 0.469,0.25 10 false CG4B 4.969,0.771 5.208,1.01 0.24,0.24 10 false 14 4.99,1.917 5.229,2.156 0.24,0.24 10 false 13 5.031,2.688 6.563,3.448 1.531,0.76 10 false Certification ECU (Smart Key ECU Assembly) 5.042,2.542 5.469,2.781 0.427,0.24 10 false I38 5.813,1.406 6.281,1.656 0.469,0.25 10 false IC 0.99,1.406 1.458,1.656 0.469,0.25 10 false IC

for LHD:
B610733E13
0.354,2.74 2.917,3.281 2.563,0.542 10 false Rear Door Outside Handle Assembly LH 0.354,2.573 1.906,2.802 1.552,0.229 10 false P8 1.771,0.771 2.01,1.01 0.24,0.24 10 false 4 1.781,1.917 2.021,2.156 0.24,0.24 10 false 6 1.323,0.771 1.688,1 0.365,0.229 10 false ANT1 1.323,1.917 1.688,2.146 0.365,0.229 10 false ANT2 5.25,0.771 5.719,1.021 0.469,0.25 10 false CLG3 5.26,1.917 5.729,2.167 0.469,0.25 10 false CG3B 4.979,0.771 5.219,1.01 0.24,0.24 10 false 27 4.979,1.917 5.219,2.156 0.24,0.24 10 false 26 5.104,2.719 6.646,3.292 1.542,0.573 10 false Certification ECU (Smart Key ECU Assembly) 5.094,2.573 5.521,2.813 0.427,0.24 10 false I38 5.813,1.417 6.281,1.677 0.469,0.26 10 false IC 0.99,1.396 1.458,1.656 0.469,0.26 10 false IC

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

After repair, confirm that no DTCs are output.



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

2.CHECK ENTRY OPERATION

NG

2.CHECK ENTRY OPERATION
a.

Check the entry unlock function.

i.
B581631C01
1.083,0.5 1.5,0.5 1.5,0.5 2,1.5 false 0.896,0.438 1.208,0.635 0.313,0.198 10 false *a
*a Unlock Sensor (Backside)

The illustrations shown are examples only.


Turn the ignition switch off.


ii.

Open and close the rear door LH.


iii.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.


iv.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the rear door LH.


v.

Check that the LED of the electrical key transmitter sub-assembly blinks.


vi.

Touch the unlock sensor on the backside of the rear door outside handle assembly LH for 2 seconds or more.*

*: Perform this step 3 seconds or more after performing step (3).


HINT:

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (1).




Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

3.READ VALUE USING GTS (RL DOOR LOCK POSITION SWITCH STATUS)

B

3.READ VALUE USING GTS (RL DOOR LOCK POSITION SWITCH STATUS)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Door Lock Position Switch Status Rear door LH unlock detection switch signal Lock or Unlock Lock: Rear door LH locked
Unlock: Rear door LH unlocked
-
Body Electrical > Main Body > Data List
Tester Display
RL Door Lock Position Switch Status
50003 449 23
OK:

The GTS display changes correctly in response to the lock/unlock operation of the rear door LH.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (REAR DRIVER SIDE UNLOCK SENSOR, REAR PASSENGER SIDE UNLOCK SENSOR)

NG

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

4.READ VALUE USING GTS (REAR DRIVER SIDE UNLOCK SENSOR, REAR PASSENGER SIDE UNLOCK SENSOR)
a.
B581631C01
1.083,0.5 1.5,0.5 1.5,0.5 2,1.5 false 0.896,0.438 1.208,0.635 0.313,0.198 10 false *a
*a Unlock Sensor (Backside)

The illustrations shown are examples only.


Open and close the rear door LH.


b.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.


c.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the rear door LH.


d.

Check that the LED of the electrical key transmitter sub-assembly blinks.


e.

Read the Data List according to the display on the GTS.


f.

Touch the unlock sensor on the backside of the rear door outside handle assembly LH for 2 seconds or more.*

*: Perform this step 3 seconds or more after performing step (b).


HINT:

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (a).


Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Driver Side Unlock Sensor Rear door LH touch sensor (unlock sensor)*1 OFF or ON OFF: Rear door LH touch sensor (unlock sensor) not touched
ON: Rear door LH touch sensor (unlock sensor) touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


Rear Passenger Side Unlock Sensor Rear door LH touch sensor (unlock sensor)*2 OFF or ON OFF: Rear door LH touch sensor (unlock sensor) not touched
ON: Rear door LH touch sensor (unlock sensor) touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


*1: for LHD

*2: for RHD


Body Electrical > Entry&Start > Data List
Tester Display
Rear Driver Side Unlock Sensor
Rear Passenger Side Unlock Sensor
50003 440 97,98
OK:

The GTS display changes correctly in response to the operation of the rear door outside handle assembly LH.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY LH)
5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY LH)
a.

Disconnect the I38 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the P8 rear door outside handle assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(I38,P8)Location & Routing

Click Connector(I38)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(P8)Body>No. 2 Rear Door Wire>Rear Door Outside Handle Assembly LH

I38-27 (CLG3) - P8-4 (ANT1) Always Below 1 Ω
I38-26 (CG3B) - P8-6 (ANT2) Always Below 1 Ω
I38-27 (CLG3) or P8-4 (ANT1) - Other terminals and body ground Always 10 kΩ or higher
I38-26 (CG3B) or P8-6 (ANT2) - Other terminals and body ground Always 10 kΩ or higher


for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(I38,P8)Location & Routing

Click Connector(I38)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(P8)Body>No. 2 Rear Door Wire>Rear Door Outside Handle Assembly LH

I38-14 (CLG4) - P8-4 (ANT1) Always Below 1 Ω
I38-13 (CG4B) - P8-6 (ANT2) Always Below 1 Ω
I38-14 (CLG4) or P8-4 (ANT1) - Other terminals and body ground Always 10 kΩ or higher
I38-13 (CG4B) or P8-6 (ANT2) - Other terminals and body ground Always 10 kΩ or higher


d.

Reconnect the P8 rear door outside handle assembly LH connector.


e.

Reconnect the I38 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (REAR DRIVER SIDE UNLOCK SENSOR, REAR PASSENGER SIDE UNLOCK SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.READ VALUE USING GTS (REAR DRIVER SIDE UNLOCK SENSOR, REAR PASSENGER SIDE UNLOCK SENSOR)
a.
B581631C01
1.083,0.5 1.5,0.5 1.5,0.5 2,1.5 false 0.896,0.438 1.208,0.635 0.313,0.198 10 false *a
*a Unlock Sensor (Backside)

The illustrations shown are examples only.


Open and close the rear door LH.


b.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.


c.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the rear door LH.


d.

Check that the LED of the electrical key transmitter sub-assembly blinks.


e.

Read the Data List according to the display on the GTS.


f.

Touch the unlock sensor on the backside of the rear door outside handle assembly (for driver side) for 2 seconds or more.*

*: Perform this step 3 seconds or more after performing step (b).


HINT:

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (a).


Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Driver Side Unlock Sensor Rear door LH touch sensor (unlock sensor)*1 OFF or ON OFF: Rear door LH touch sensor (unlock sensor) not touched
ON: Rear door LH touch sensor (unlock sensor) touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


Rear Passenger Side Unlock Sensor Rear door LH touch sensor (unlock sensor)*2 OFF or ON OFF: Rear door LH touch sensor (unlock sensor) not touched
ON: Rear door LH touch sensor (unlock sensor) touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


*1: for LHD

*2: for RHD


Body Electrical > Entry&Start > Data List
Tester Display
Rear Driver Side Unlock Sensor
Rear Passenger Side Unlock Sensor
50003 440 97,98
OK:

The GTS display changes correctly in response to the operation of the rear door outside handle assembly LH.



Result:
Proceed to
OK
NG



OK

END (CONNECTOR WAS NOT CONNECTED SECURELY)

NG

REPLACE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH