Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM38G0E _58 Vehicle Interior _100749 LIGHTING (INT) _0468730 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Door Unlock Detection Switch Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of each door unlock detection switch.

WIRING DIAGRAM

E442538E04
6.688,3.542 7.021,3.844 0.333,0.302 10 false +B 6.688,2.219 7.021,2.521 0.333,0.302 10 false +B 6.698,0.823 7.031,1.125 0.333,0.302 10 false +B 5.76,1.135 6.333,1.479 0.573,0.344 10 false LSFR 5.771,2.5 6.344,2.844 0.573,0.344 10 false LSFL 5.771,3.875 6.344,4.219 0.573,0.344 10 false LSWL 5.76,5.219 6.333,5.563 0.573,0.344 10 false LSWR 5.458,5.802 7.104,6.167 1.646,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 5.448,2.406 5.677,2.698 0.229,0.292 10 false 9 1.135,3.021 2.844,3.396 1.708,0.375 10 false N2 1.135,3.188 3.771,3.563 2.635,0.375 10 false Front Door with Motor Lock Assembly LH 1.063,1.615 2.771,1.99 1.708,0.375 10 false M2 1.063,1.813 3.677,2.083 2.615,0.271 10 false Front Door with Motor Lock Assembly RH 2.198,1.385 3.906,1.76 1.708,0.375 10 false LSSR 1.625,2.74 3.333,3.115 1.708,0.375 10 false E 1.615,4.125 3.323,4.5 1.708,0.375 10 false E 1.635,5.469 3.344,5.844 1.708,0.375 10 false E 2.198,5.5 3.906,5.875 1.708,0.375 10 false LSSR 2.208,4.125 3.917,4.5 1.708,0.375 10 false LSSR 1.104,4.406 3.625,4.792 2.521,0.385 10 false P1*1, P2*2 1.094,5.781 3.083,6.219 1.99,0.438 10 false O1*1, O2*2 1.094,5.948 3.646,6.323 2.552,0.375 10 false Rear Door with Motor Lock Assembly RH 2.208,2.75 3.917,3.125 1.708,0.375 10 false LSSR 2.698,3.854 4.406,4.229 1.708,0.375 10 false 6*1, 9*2 2.719,5.24 4.427,5.615 1.708,0.375 10 false 9*1, 5*2 5.417,5.135 5.729,5.427 0.313,0.292 10 false 23 5.438,5.344 5.896,5.583 0.458,0.24 10 false I2 6.698,4.927 7.031,5.229 0.333,0.302 10 false +B 0.979,1.094 2.208,1.458 1.229,0.365 10 false 8*1, 6*2 1.615,1.354 1.771,1.552 0.156,0.198 10 false E 2.719,1.104 3.427,1.625 0.708,0.521 10 false 7*1, 5*2 0.917,3.833 2.625,4.208 1.708,0.375 10 false 9*1, 10*2 1.375,5.219 3.083,5.594 1.708,0.375 10 false 6 1.083,4.583 3.604,4.969 2.521,0.385 10 false Rear Door with Motor Lock Assembly LH 5.417,3.979 5.875,4.219 0.458,0.24 10 false I3 5.385,3.781 5.698,4.073 0.313,0.292 10 false 10 5.458,1.031 5.688,1.323 0.229,0.292 10 false 3 5.427,2.604 5.885,2.844 0.458,0.24 10 false I3 5.427,1.24 5.885,1.479 0.458,0.24 10 false I3 2.198,6.427 4.75,6.802 2.552,0.375 10 false *2: w/ Double Locking System 0.094,6.417 2.656,6.604 2.563,0.188 10 false *1: w/o Double Locking System 2.698,2.469 4.406,2.844 1.708,0.375 10 false 8*1, 10*2 0.969,2.469 2.677,2.844 1.708,0.375 10 false 7*1, 9*2

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.


PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Lock Position Switch Status Front door RH unlock detection switch signal Unlock or Lock Unlock: Front door RH unlocked
Lock: Front door RH locked
-
FL Door Lock Position Switch Status Front door LH unlock detection switch signal Unlock or Lock Unlock: Front door LH unlocked
Lock: Front door LH locked
-
RR Door Lock Position Switch Status Rear door RH unlock detection switch signal Unlock or Lock Unlock: Rear door RH unlocked
Lock: Rear door RH locked
-
RL Door Lock Position Switch Status Rear door LH unlock detection switch signal Unlock or Lock Unlock: Rear door LH unlocked
Lock: Rear door LH locked
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Lock Position Switch Status
FL Door Lock Position Switch Status
RR Door Lock Position Switch Status
RL Door Lock Position Switch Status
50003 449 20,21,22,23
OK:

Normal conditions listed above are displayed.



Result:
Result Proceed to
OK A
NG ("FR Door Lock Position Switch Status" is abnormal) B
NG ("FL Door Lock Position Switch Status" is abnormal) C
NG ("RR-Door Lock Position Switch Status" is abnormal) D
NG ("RL-Door Lock Position Switch Status" is abnormal) E



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY RH

C

4.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH

D

6.INSPECT REAR DOOR WITH MOTOR LOCK ASSEMBLY RH

E

8.INSPECT REAR DOOR WITH MOTOR LOCK ASSEMBLY LH
2.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY RH

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR WITH MOTOR LOCK ASSEMBLY RH - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPLACE FRONT DOOR WITH MOTOR LOCK ASSEMBLY RH

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR WITH MOTOR LOCK ASSEMBLY RH - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the M2 front door with motor lock assembly RH connector.


b.

Disconnect the I3 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Double Locking System
Tester Connection Condition Specified Condition

Click Location & Routing(M2,I3)Location & Routing

Click Connector(M2)Body>Front Door Wire RH>Front Door Lock with Motor Assembly RH

Click Connector(I3)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

M2-7 (LSSR) - I3-3 (LSFR) Always Below 1 Ω
M2-8 (E) - Body ground Always Below 1 Ω
M2-7 (LSSR) or I3-3 (LSFR) - Body ground Always 10 kΩ or higher

w/ Double Locking System
Tester Connection Condition Specified Condition

Click Location & Routing(M2,I3)Location & Routing

Click Connector(M2)Body>Front Door Wire RH>Front Door Lock with Motor Assembly RH

Click Connector(I3)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

M2-5 (LSSR) - I3-3 (LSFR) Always Below 1 Ω
M2-6 (E) - Body ground Always Below 1 Ω
M2-5 (LSSR) or I3-3 (LSFR) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPLACE FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH

5.CHECK HARNESS AND CONNECTOR (FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the N2 front door with motor lock assembly LH connector.


b.

Disconnect the I3 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Double Locking System
Tester Connection Condition Specified Condition

Click Location & Routing(N2,I3)Location & Routing

Click Connector(N2)Body>Front Door Wire LH>Front Door Lock with Motor Assembly LH

Click Connector(I3)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

N2-8 (LSSR) - I3-9 (LSFL) Always Below 1 Ω
N2-7 (E) - Body ground Always Below 1 Ω
N2-8 (LSSR) or I3-9 (LSFL) - Body ground Always 10 kΩ or higher

w/ Double Locking System
Tester Connection Condition Specified Condition

Click Location & Routing(N2,I3)Location & Routing

Click Connector(N2)Body>Front Door Wire LH>Front Door Lock with Motor Assembly LH

Click Connector(I3)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

N2-10 (LSSR) - I3-9 (LSFL) Always Below 1 Ω
N2-9 (E) - Body ground Always Below 1 Ω
N2-10 (LSSR) or I3-9 (LSFL) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT REAR DOOR WITH MOTOR LOCK ASSEMBLY RH

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (REAR DOOR WITH MOTOR LOCK ASSEMBLY RH - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPLACE REAR DOOR WITH MOTOR LOCK ASSEMBLY RH

7.CHECK HARNESS AND CONNECTOR (REAR DOOR WITH MOTOR LOCK ASSEMBLY RH - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the O1*1, O2*2 rear door with motor lock assembly RH connector.

*1: w/o Double Locking System

*2: w/ Double Locking System



b.

Disconnect the I2 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Double Locking System
Tester Connection Condition Specified Condition

Click Location & Routing(O1,I2)Location & Routing

Click Connector(O1)Body>No. 1 Rear Door Wire>Rear Door Lock with Motor Assembly RH

Click Connector(I2)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

O1-9 (LSSR) - I2-23 (LSWR) Always Below 1 Ω
O1-6 (E) - Body ground Always Below 1 Ω
O1-9 (LSSR) or I2-23 (LSWR) - Body ground Always 10 kΩ or higher

w/ Double Locking System
Tester Connection Condition Specified Condition

Click Location & Routing(O2,I2)Location & Routing

Click Connector(O2)Body>No. 1 Rear Door Wire>Rear Door Lock with Motor Assembly RH

Click Connector(I2)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

O2-5 (LSSR) - I2-23 (LSWR) Always Below 1 Ω
O2-6 (E) - Body ground Always Below 1 Ω
O2-5 (LSSR) or I2-23 (LSWR) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT REAR DOOR WITH MOTOR LOCK ASSEMBLY LH

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION

Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (REAR DOOR WITH MOTOR LOCK ASSEMBLY LH - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPLACE REAR DOOR WITH MOTOR LOCK ASSEMBLY LH

9.CHECK HARNESS AND CONNECTOR (REAR DOOR WITH MOTOR LOCK ASSEMBLY LH - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the P1*1, P2*2 rear door with motor lock assembly LH connector.

*1: w/o Double Locking System

*2: w/ Double Locking System



b.

Disconnect the I3 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Double Locking System
Tester Connection Condition Specified Condition

Click Location & Routing(P1,I3)Location & Routing

Click Connector(P1)Body>No. 2 Rear Door Wire>Rear Door Lock with Motor Assembly LH

Click Connector(I3)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

P1-6 (LSSR) - I3-10 (LSWL) Always Below 1 Ω
P1-9 (E) - Body ground Always Below 1 Ω
P1-6 (LSSR) or I3-10 (LSWL) - Body ground Always 10 kΩ or higher

w/ Double Locking System
Tester Connection Condition Specified Condition

Click Location & Routing(P2,I3)Location & Routing

Click Connector(P2)Body>No. 2 Rear Door Wire>Rear Door Lock with Motor Assembly LH

Click Connector(I3)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

P2-9 (LSSR) - I3-10 (LSWL) Always Below 1 Ω
P2-10 (E) - Body ground Always Below 1 Ω
P2-9 (LSSR) or I3-10 (LSWL) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR