Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467507 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B227111  IG Circuit Short to Ground  


DESCRIPTION

This DTC is stored when a malfunction in the IG circuit or IG hold circuit of the certification ECU (smart key ECU assembly) is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B227111 IG Circuit Short to Ground When either of the following conditions is met (1-trip detection logic*1):
·

The IG circuit of the certification ECU (smart key ECU assembly) is malfunctioning.*2

·

The IG hold circuit of the certification ECU (smart key ECU assembly) is malfunctioning.*3


·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


Power Source Control A
DTC Output Confirmation Operation:

Turn the ignition switch to ON.



*1: Only detected while a malfunction is present and the ignition switch is ON.

*2: The IG circuit and IG hold circuit activate the IG relay.

*3: After the IG circuit turns on, even if the certification ECU (smart key ECU assembly) malfunctions, the IG hold circuit will maintain the power source mode in ON.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The ignition switch cannot be turned to ON (the engine cannot be started). The power source mode cannot be changed to ON.

Related Data List and Active Test Items
DTC No. Data List and Active Test
B227111
Power Source Control
·

IGP Relay Circuit (Outside) Monitor

·

IGR Relay Circuit (Outside) Monitor



WIRING DIAGRAM

B570095E13
5.208,3.75 6.781,4.208 1.573,0.458 10 false Certification ECU (Smart Key ECU Assembly) 5.26,1.365 5.708,1.729 0.448,0.365 10 false IGPD 5.271,2.292 5.719,2.656 0.448,0.365 10 false IGRD 6.229,1.688 6.677,2.052 0.448,0.365 10 false IC 5.771,1.885 6.219,2.25 0.448,0.365 10 false +B 5.792,0.969 6.24,1.333 0.448,0.365 10 false +B 1.396,1.469 2.354,1.729 0.958,0.26 10 false to IGP Relay 1.406,2.396 2.521,2.708 1.115,0.313 10 false to IGR Relay 5.208,3.583 6.323,4.021 1.115,0.438 10 false I40 4.99,1.365 5.438,1.729 0.448,0.365 10 false 24 4.979,2.292 5.427,2.656 0.448,0.365 10 false 11

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B574625C50
1.354,0.052 1.729,0.24 0.375,0.188 2.094,2.01 1.979,2.01 1.979,2.01 1.688,0.917 false 2.281,1.854 2.167,1.854 2.167,1.854 1.76,0.802 false 1.417,0.052 1.875,0.25 0.458,0.198 10 false I40 2.333,1.771 2.948,1.969 0.615,0.198 10 false IGRD 2.156,1.948 2.771,2.146 0.615,0.198 10 false IGPD 0.188,0.052 0.802,0.25 0.615,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I40)Location & Routing

Click Connector(I40)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

I40-11 (IGRD) - Body ground Ignition switch ACC 1 V or less
I40-11 (IGRD) - Body ground Ignition switch ON 9 V or higher
I40-24 (IGPD) - Body ground Ignition switch ACC 1 V or less
I40-24 (IGPD) - Body ground Ignition switch ON 9 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)