Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467507 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B27A713  Rear Floor 2 Electrical Key Oscillator Circuit Open  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 3 indoor electrical key antenna assembly (inside luggage compartment). For the No. 3 indoor electrical key antenna assembly (inside luggage compartment) to detect when the electrical key transmitter sub-assembly is in the cabin, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the vehicle. DTC B27A713 is stored by the certification ECU (smart key ECU assembly) when an open is detected between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (inside luggage compartment) (between terminals CLG7 and ANTE7, or terminals CG7B and CLGB).

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B27A713 Rear Floor 2 Electrical Key Oscillator Circuit Open An open is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (inside luggage compartment) (CLG7 - ANTE7, CG7B - CLGB) (1 trip detection logic*).
·

Certification ECU (smart key ECU assembly)

·

No. 3 indoor electrical key antenna assembly (inside luggage compartment)

·

Harness or connector


Entry&Start A
DTC Output Confirmation Operation:

Any time



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
When electrical key transmitter sub-assembly is in rear floor:
·

Power source mode does not charge when engine switch pressed

·

Electrical key transmitter sub-assembly locked inside vehicle


-

Related Data List and Active Test
DTC No. Data List and Active Test
B27A713 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B574804E17
1.229,0.75 1.844,0.948 0.615,0.198 10 false ANTE7 1.302,1.906 1.917,2.104 0.615,0.198 10 false CLGB 1.781,0.75 1.938,0.948 0.156,0.198 10 false 1 1.781,1.906 1.938,2.104 0.156,0.198 10 false 2 0.094,2.531 0.51,2.75 0.417,0.219 10 false Q31 0.083,2.698 2.938,3.615 2.854,0.917 10 false No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment) 4.969,0.656 5.281,0.854 0.313,0.198 10 false 10 5.021,1.802 5.333,2 0.313,0.198 10 false 9 5.313,0.75 5.927,0.948 0.615,0.198 10 false CLG7 4.969,0.865 5.427,1.063 0.458,0.198 10 false I38 4.969,2.01 5.427,2.208 0.458,0.198 10 false I38 6.49,2.01 6.948,2.208 0.458,0.198 10 false I39 6.521,1.802 6.833,2 0.313,0.198 10 false 29 6.25,2.031 6.406,2.229 0.156,0.198 10 false E 5.313,1.906 5.927,2.104 0.615,0.198 10 false CG7B 5.833,1.458 6.146,1.656 0.313,0.198 10 false IC 5.083,2.552 6.604,3.094 1.521,0.542 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (inside luggage compartment).

OK:

Connectors are properly connected.


Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))

Pre-procedure1

a.

Disconnect the I38 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the Q31 No. 3 indoor electrical key antenna assembly (inside luggage compartment) connector.


Procedure1


Post-procedure1

d.

None



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))

Pre-procedure1

a.

Connect the I38 certification ECU (smart key ECU assembly) connector.


Procedure1

b.

Using an oscilloscope, check the waveform.

B587056C15
4.792,0.406 5.156,0.677 0.365,0.271 3.406,0.417 3.771,0.688 0.365,0.271 5.375,2.49 5.198,2.49 5.198,2.49 4.583,1.26 false 3.281,2.479 3.51,2.479 3.51,2.479 3.771,1.167 false 2.99,2.302 3.219,2.302 3.219,2.302 3.688,1.167 false 0.156,0.167 0.469,0.323 0.313,0.156 10 false *a 2.125,3.125 2.438,3.281 0.313,0.156 10 false *b 3.167,4.698 3.479,4.854 0.313,0.156 10 false *c 2.333,4.135 3.021,4.479 0.688,0.344 10 false GND 4.146,4.708 4.458,4.865 0.313,0.156 10 false *d 2.875,2.417 3.563,2.76 0.688,0.344 10 false CG7B 2.604,2.208 3.292,2.552 0.688,0.344 10 false CLG7 5.427,2.417 6.115,2.76 0.688,0.344 10 false E 4.885,0.448 5.573,0.792 0.688,0.344 10 false I39 3.51,0.458 4.198,0.802 0.688,0.344 10 false I38
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform
*c For 30 seconds after any door closed *d After 30 seconds or more have elapsed since any door closed


OK:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(I38,I39)Location & Routing

Click Connector(I38)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(I39)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

I38-10 (CLG7) - I39-29 (E) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)
I38-9 (CG7B) - I39-29 (E) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)