Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467512 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B277B87  Fingerprint for Engine/Power Switch Missing Message  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and engine switch stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B277B87 Fingerprint for Engine/Power Switch Missing Message No communication between certification ECU (smart key ECU assembly) and engine switch for 10 seconds or more.
·

Engine switch

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


Entry&Start A

WIRING DIAGRAM

C458694E03
2.167,0.927 2.563,1.177 0.396,0.25 10 false 8 4.052,0.938 4.448,1.188 0.396,0.25 10 false 4 5.188,0.917 5.583,1.167 0.396,0.25 10 false 10 4.031,1.885 4.427,2.135 0.396,0.25 10 false 3 1.854,1.042 2.25,1.292 0.396,0.25 10 false LIN 4.229,1.021 4.625,1.271 0.396,0.25 10 false LIN 4.896,1.063 5.292,1.313 0.396,0.25 10 false +B 4.26,1.99 4.656,2.24 0.396,0.25 10 false GND 4.906,0.375 5.781,0.583 0.875,0.208 10 false from Battery 5.396,1.25 6.479,1.417 1.083,0.167 10 false ECU-B NO. 2 4.188,2.427 5.271,2.594 1.083,0.167 10 false I75 0.698,2.281 1.781,2.448 1.083,0.167 10 false I39 0.688,2.458 2.271,2.875 1.583,0.417 10 false Certification ECU (Smart Key ECU Assembly) 4.198,2.594 5.594,2.865 1.396,0.271 10 false Engine Switch 0.75,3.417 2.75,3.667 2,0.25 10 false : LIN Communication Line 1.667,2 2.271,2.26 0.604,0.26 10 false AGND 2.198,1.865 2.594,2.115 0.396,0.25 10 false 30

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is replaced, refer to Service Bulletin.

·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 440

b.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440

Result:
Result Proceed to
DTC B277B87 and B278588 are output A
Only DTC B277B87 is output B
DTC B277B87 and B278588 are not output C



A

B

2.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

C

2.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the I75 engine switch connector.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH POWER SOURCE CIRCUIT)
a.

Disconnect the I75 engine switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I75)Location & Routing

Click Connector(I75)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Switch (Push Start Switch)

I75-10 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - BODY GROUND)
a.

Disconnect the I75 engine switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I75)Location & Routing

Click Connector(I75)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Switch (Push Start Switch)

I75-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE SWITCH

NG

5.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
5.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the I75 engine switch connector.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR