Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2021.04–2021.07
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467512 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B278588  Communication between ECUs connected by LIN Bus off  


DESCRIPTION

If the certification ECU (smart key ECU assembly) detects a communication error with an ECU connected to the certification bus lines for 7 seconds or more, DTC B278588 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B278588 Communication between ECUs connected by LIN Bus off
·

Errors in LIN communication between ECUs or an open or short in communication lines.

·

The certification ECU (smart key ECU assembly) detects a communication error with an ECU connected to the certification bus lines for 7 seconds or more.


·

Certification ECU (smart key ECU assembly)

·

Steering lock actuator with ECU assembly

·

ID code box (immobiliser code ECU)

·

Engine switch (w/ Fingerprint Authentication)

·

Harness or connector


Entry&Start A

WIRING DIAGRAM

C458692E14
5.292,1.729 6.854,2.156 1.563,0.427 10 false Steering Lock Actuator with ECU Assembly 0.396,1.625 1.917,2.042 1.521,0.417 10 false Certification ECU (Smart Key ECU Assembly) 5.219,3.5 6.792,3.938 1.573,0.438 10 false ID Code Box (Immobiliser Code ECU) 0.708,4.333 2.406,4.667 1.698,0.333 10 false : LIN Communication Line 0.365,3.531 1.938,3.969 1.573,0.438 10 false Engine Switch* 0.281,4.031 2.302,4.469 2.021,0.438 10 false *: w/ Fingerprint Authentication 0.417,1.479 0.979,1.698 0.563,0.219 10 false I39 5.271,1.542 5.833,1.76 0.563,0.219 10 false I49 0.354,3.365 0.917,3.583 0.563,0.219 10 false I75 5.208,3.344 5.771,3.563 0.563,0.219 10 false I66 5.292,2.802 5.854,3.021 0.563,0.219 10 false LIN1 1.646,0.979 2.208,1.198 0.563,0.219 10 false LIN 1.656,2.823 2.219,3.042 0.563,0.219 10 false LIN 5.302,0.958 5.865,1.177 0.563,0.219 10 false LIN

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing the inspection, check that DTC B278187 or B278C87 is not output.

·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) or steering lock actuator with ECU assembly, refer to Service Bulletin.



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 440

b.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440

Result:
Result Proceed to
DTC B278588 is output A
DTC B278588 is not output B



A

2.CHECK FOR DTC

B

2.CHECK FOR DTC
a.

Disconnect the I49 steering lock actuator with ECU assembly connector.


b.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 440

c.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440

Result:
Result Proceed to
DTC B278588 is output A
DTC B278588 is not output B



A

3.CHECK FOR DTC

B

3.CHECK FOR DTC
a.

Disconnect the I66 ID code box (immobiliser code ECU) connector.


b.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 440

c.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440

Result:
Result Proceed to
DTC B278588 is output A
DTC B278588 is not output B



A

4.CHECK FOR VEHICLE TYPE

B

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

4.CHECK FOR VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
Vehicle with fingerprint authentication A
Vehicle without fingerprint authentication B



A

5.CHECK FOR DTC

B

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - EACH ECU)
5.CHECK FOR DTC
a.

Disconnect the I75 engine switch connector.


b.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 440

c.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440

Result:
Result Proceed to
DTC B278588 is output A
DTC B278588 is not output B



A

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - EACH ECU)

B

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - EACH ECU)
a.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the I49 steering lock actuator with ECU assembly connector.


c.

Disconnect the I66 ID code box (immobiliser code ECU) connector.


d.

w/ Fingerprint Authentication:

Disconnect the I75 engine switch connector.


e.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition

*: w/ Fingerprint Authentication

Click Location & Routing(I39,I49,I66,I75)Location & Routing

Click Connector(I39)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

Click Connector(I66)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>ID Code Box

Click Connector(I75)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Switch (Push Start Switch)

I39-8 (LIN) - I49-5 (LIN) Always Below 1 Ω
I39-8 (LIN) or I49-5 (LIN) - Body ground Always 10 kΩ or higher
I39-8 (LIN) - I66-2 (LIN1) Always Below 1 Ω
I39-8 (LIN) or I66-2 (LIN1) - Body ground Always 10 kΩ or higher
I39-8 (LIN) - I75-4 (LIN)* Always Below 1 Ω
I75-4 (LIN) - Body ground* Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR