Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467512 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B278987  ID-BOX Missing Message  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B278987 ID-BOX Missing Message No communication between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) for 10 seconds or more.
·

ID code box (immobiliser code ECU)

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


Entry&Start A

WIRING DIAGRAM

B463707E16
2.167,1.302 2.563,1.552 0.396,0.25 10 false 8 4.052,1.302 4.448,1.552 0.396,0.25 10 false 2 5.188,0.917 5.583,1.167 0.396,0.25 10 false 1 5.177,1.854 5.573,2.104 0.396,0.25 10 false 5 1.854,1.458 2.25,1.708 0.396,0.25 10 false LIN 4.229,1.458 4.625,1.708 0.396,0.25 10 false LIN1 4.896,1.063 5.292,1.313 0.396,0.25 10 false +B 4.771,1.99 5.167,2.24 0.396,0.25 10 false GND 4.917,0.385 5.865,0.604 0.948,0.219 10 false from Battery 5.396,1.25 6.479,1.417 1.083,0.167 10 false ECU-B NO. 1 3.917,2.292 5,2.458 1.083,0.167 10 false I66 0.698,2.281 1.781,2.448 1.083,0.167 10 false I39 0.688,2.458 2.271,2.875 1.583,0.417 10 false Certification ECU (Smart Key ECU Assembly) 3.917,2.5 5.5,3 1.583,0.5 10 false ID Code Box (Immobiliser Code ECU) 0.708,3.469 2.708,3.719 2,0.25 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is replaced, refer to Service Bulletin.

·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 440

b.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440

Result:
Result Proceed to
DTC B278987 and B278588 are output A
Only DTC 278987 is output B
DTC B278987 and B278588 are not output C



A

B

2.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) POWER SOURCE CIRCUIT)

C

2.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) POWER SOURCE CIRCUIT)
a.

Disconnect the I66 ID code box (immobiliser code ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I66)Location & Routing

Click Connector(I66)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>ID Code Box

I66-5 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I66)Location & Routing

Click Connector(I66)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>ID Code Box

I66-1 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ID CODE BOX (IMMOBILISER CODE ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ID CODE BOX (IMMOBILISER CODE ECU))
a.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the I66 ID code box (immobiliser code ECU) connector.



Result:
Proceed to
OK
NG



OK

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR