Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM38G0E _58 Vehicle Interior _100628 SEAT _0467514 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2650  Slide Sensor Malfunction  


DESCRIPTION

When the position control ECU assembly does not receive a slide motor position sensor signal despite the seat having been moved forward or backward by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2650 Slide Sensor Malfunction Slide motor position sensor signal not received when power seat moved forward or backward
·

Position control ECU assembly

·

Slide motor (front seat adjuster assembly LH) (for LHD)

·

Slide motor (front seat adjuster assembly RH) (for RHD)

·

Harness or connector


Driver Seat A

WIRING DIAGRAM

for LHD:


B591059E05
1.219,2.479 2.229,2.76 1.01,0.281 10 false i11 4.844,1.052 5.302,1.25 0.458,0.198 10 false i17 4.833,0.542 5.292,0.74 0.458,0.198 10 false i17 4.833,2.083 5.292,2.281 0.458,0.198 10 false i19 4.844,1.573 5.302,1.771 0.458,0.198 10 false i19 5.229,0.542 5.844,0.74 0.615,0.198 10 false SLD+ 5.229,1.052 5.844,1.25 0.615,0.198 10 false SLD- 5.24,1.563 5.854,1.76 0.615,0.198 10 false SSRS 5.24,2.083 5.854,2.281 0.615,0.198 10 false SGND 1.219,2.635 2.906,2.833 1.688,0.198 10 false Slide Motor 4.729,2.615 7,2.958 2.271,0.344 10 false Position Control ECU Assembly 0.604,3.094 4.594,3.375 3.99,0.281 10 false Front Seat Adjuster Assembly LH 4.885,0.302 5.042,0.5 0.156,0.198 10 false 1 4.896,0.823 5.052,1.021 0.156,0.198 10 false 5 4.844,1.333 5.156,1.531 0.313,0.198 10 false 26 4.844,1.844 5.156,2.042 0.313,0.198 10 false 12 2.333,1.458 3.094,1.677 0.76,0.219 10 false 2 2.333,0.427 2.49,0.625 0.156,0.198 10 false 4 2.323,0.958 3.323,1.323 1,0.365 10 false 1 2.333,1.969 3.104,2.24 0.771,0.271 10 false 3


for RHD:


B591059E06
1.219,2.479 2.229,2.76 1.01,0.281 10 false h1 4.844,1.052 5.302,1.25 0.458,0.198 10 false h22 4.833,0.542 5.292,0.74 0.458,0.198 10 false h22 4.833,2.083 5.292,2.281 0.458,0.198 10 false h24 4.844,1.573 5.302,1.771 0.458,0.198 10 false h24 5.229,0.542 5.844,0.74 0.615,0.198 10 false SLD+ 5.229,1.052 5.844,1.25 0.615,0.198 10 false SLD- 5.24,1.563 5.854,1.76 0.615,0.198 10 false SSRS 5.24,2.083 5.854,2.281 0.615,0.198 10 false SGND 1.219,2.635 2.906,2.833 1.688,0.198 10 false Slide Motor 4.74,2.615 7.063,2.948 2.323,0.333 10 false Position Control ECU Assembly 0.604,3.094 4.594,3.375 3.99,0.281 10 false Front Seat Adjuster Assembly RH 4.885,0.302 5.042,0.5 0.156,0.198 10 false 1 4.896,0.823 5.052,1.021 0.156,0.198 10 false 5 4.844,1.333 5.156,1.531 0.313,0.198 10 false 26 4.844,1.844 5.156,2.042 0.313,0.198 10 false 12 2.333,1.458 3.094,1.677 0.76,0.219 10 false 2 2.333,0.427 2.49,0.625 0.156,0.198 10 false 4 2.323,0.958 3.323,1.323 1,0.365 10 false 1 2.333,1.969 3.104,2.24 0.771,0.271 10 false 3


CAUTION / NOTICE / HINT

NOTICE:

Initializing the position control ECU assembly will clear the seat position memory.


HINT:

Make sure to initialize the position control ECU assembly after replacing the seat assembly or any related parts (including removal and installation).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>REGISTRATION


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CLEAR DTC

B

10.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162

Result:
Result Proceed to
B2650 is not output A
B2650 is output B



A

B

4.PERFORM ACTIVE TEST USING GTS (SEAT SLIDE OPERATION)
4.PERFORM ACTIVE TEST USING GTS (SEAT SLIDE OPERATION)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Slide Operation Seat slide operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Slide Operation
50004 162 4
OK:

Slide motor operates normally.



Result:
Proceed to
OK
NG



OK

5.CHECK POSITION CONTROL ECU ASSEMBLY (SLIDE MOTOR CIRCUIT)

NG

8.INSPECT SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH)
5.CHECK POSITION CONTROL ECU ASSEMBLY (SLIDE MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the i11 slide motor (front seat adjuster assembly LH) connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(i11)Location & Routing

Click Connector(i11)Seat>Front Seat Wire LH>Power Seat Slide Motor LH (Front Seat Adjuster Assembly LH)

i11-2 - i11-3 Slide switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

6.CHECK SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH)

NG

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH))
6.CHECK SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(i11)Location & Routing

Click Connector(i11)Seat>Front Seat Wire LH>Power Seat Slide Motor LH (Front Seat Adjuster Assembly LH)

i11-2 - Body ground Slide motor operating 4.5 to 4.8 V


Result:
Proceed to
OK
NG




OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPLACE SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH)

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH))

Pre-procedure1

a.

Disconnect the i19 position control ECU assembly connector.


b.

Disconnect the i11 slide motor (front seat adjuster assembly LH) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(i19,i11)Location & Routing

Click Connector(i19)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LH

Click Connector(i11)Seat>Front Seat Wire LH>Power Seat Slide Motor LH (Front Seat Adjuster Assembly LH)

i19-26 (SSRS) - i11-2 Always Below 1 Ω
i19-26 (SSRS) or i11-2 - Body ground Always 10 kΩ or higher
i19-12 (SGND) - i11-3 Always Below 1 Ω
i19-12 (SGND) or i11-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH)

OK

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH))

NG

REPLACE SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH)

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH))

Pre-procedure1

a.

Disconnect the i17 position control ECU assembly connector.


b.

Disconnect the i11 slide motor (front seat adjuster assembly LH) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(i17,i11)Location & Routing

Click Connector(i17)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LH

Click Connector(i11)Seat>Front Seat Wire LH>Power Seat Slide Motor LH (Front Seat Adjuster Assembly LH)

i17-1 (SLD+) - i11-4 Always Below 1 Ω
i17-1 (SLD+) or i11-4 - Body ground Always 10 kΩ or higher
i17-5 (SLD-) - i11-1 Always Below 1 Ω
i17-5 (SLD-) or i11-1 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162

Result:
Result Proceed to
B2650 is not output A
B2650 is output B



A

B

12.PERFORM ACTIVE TEST USING GTS (SEAT SLIDE OPERATION)
12.PERFORM ACTIVE TEST USING GTS (SEAT SLIDE OPERATION)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Slide Operation Seat slide operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Slide Operation
50004 162 4
OK:

Slide motor operates normally.



Result:
Proceed to
OK
NG



OK

13.CHECK POSITION CONTROL ECU ASSEMBLY (SLIDE MOTOR CIRCUIT)

NG

16.INSPECT SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY RH)
13.CHECK POSITION CONTROL ECU ASSEMBLY (SLIDE MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the h1 slide motor (front seat adjuster assembly RH) connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(h1)Location & Routing

Click Connector(h1)Seat>Front Seat Wire RH>Power Seat Slide Motor RH (Front Seat Adjuster Assembly RH)

h1-2 - h1-3 Slide switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

14.CHECK SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY RH)

NG

15.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY RH))
14.CHECK SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY RH)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(h1)Location & Routing

Click Connector(h1)Seat>Front Seat Wire RH>Power Seat Slide Motor RH (Front Seat Adjuster Assembly RH)

h1-2 - Body ground Slide motor operating 4.5 to 4.8 V


Result:
Proceed to
OK
NG




OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPLACE SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY RH)

15.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY RH))

Pre-procedure1

a.

Disconnect the h24 position control ECU assembly connector.


b.

Disconnect the h1 slide motor (front seat adjuster assembly RH) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(h24,h1)Location & Routing

Click Connector(h24)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RH

Click Connector(h1)Seat>Front Seat Wire RH>Power Seat Slide Motor RH (Front Seat Adjuster Assembly RH)

h24-26 (SSRS) - h1-2 Always Below 1 Ω
h24-26 (SSRS) or h1-2 - Body ground Always 10 kΩ or higher
h24-12 (SGND) - h1-3 Always Below 1 Ω
h24-12 (SGND) or h1-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY RH)

OK

17.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY RH))

NG

REPLACE SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY RH)

17.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY RH))

Pre-procedure1

a.

Disconnect the h22 position control ECU assembly connector.


b.

Disconnect the h1 slide motor (front seat adjuster assembly RH) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(h22,h1)Location & Routing

Click Connector(h22)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RH

Click Connector(h1)Seat>Front Seat Wire RH>Power Seat Slide Motor RH (Front Seat Adjuster Assembly RH)

h22-1 (SLD+) - h1-4 Always Below 1 Ω
h22-1 (SLD+) or h1-4 - Body ground Always 10 kΩ or higher
h22-5 (SLD-) - h1-1 Always Below 1 Ω
h22-5 (SLD-) or h1-1 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR