Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM38G0E _58 Vehicle Interior _100628 SEAT _0467514 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Front Power Seat does not Operate with Front Power Seat Switch  


DESCRIPTION

Signals are input into the position control ECU assembly. The built-in ECU manages the signals received from the power seat switch and operates each motor. If the position control ECU assembly receives more than 2 motor operation signals for the same motor, the motor will be stopped. Manual operation resumes when the position control ECU assembly receives only 1 signal.

WIRING DIAGRAM

for LHD:


B613104E01
1.542,0.271 3.427,0.563 1.885,0.292 10 false from Battery 1.542,0.833 3.427,1.125 1.885,0.292 10 false from Battery 0.979,1.406 2.865,1.698 1.885,0.292 10 false from IGR NO. 1 Relay 3.229,0.469 5.115,0.76 1.885,0.292 10 false ECU-DCC NO. 1 3.375,1.021 5.26,1.313 1.885,0.292 10 false P/SEAT F/L 3.281,1.604 4.396,1.833 1.115,0.229 10 false ECU-IGR NO. 1 4.844,0.302 5.333,0.531 0.49,0.229 10 false i19 4.833,1.417 5.323,1.646 0.49,0.229 10 false i19 6.417,0.792 6.906,1.021 0.49,0.229 10 false i17 4.844,2.25 5.333,2.479 0.49,0.229 10 false i19 4.844,0.073 5.333,0.302 0.49,0.229 10 false 15 4.885,0.625 5.375,0.854 0.49,0.229 10 false 3 4.885,1.167 5.375,1.396 0.49,0.229 10 false 1 4.854,2.01 5.344,2.24 0.49,0.229 10 false 12 5.25,0.302 5.896,0.583 0.646,0.281 10 false SYSB 5.25,0.865 5.896,1.146 0.646,0.281 10 false +B 5.25,1.438 5.896,1.719 0.646,0.281 10 false IG 5.25,2.25 5.896,2.531 0.646,0.281 10 false SGND 4.781,2.917 6.875,3.417 2.094,0.5 10 false Position Control ECU Assembly 1.271,2.646 2.229,2.927 0.958,0.281 10 false i14 1.271,2.813 3.646,3.052 2.375,0.24 10 false Front Power Seat Switch LH 2.74,2.135 3.229,2.365 0.49,0.229 10 false 20 4.833,0.854 5.323,1.083 0.49,0.229 10 false i17 6.479,0.542 6.969,0.771 0.49,0.229 10 false 2 5.969,0.802 6.615,1.083 0.646,0.281 10 false GND 2.51,2.25 3,2.479 0.49,0.229 10 false E


for RHD:


B613104E02
1.542,0.271 3.427,0.563 1.885,0.292 10 false from Battery 1.542,0.833 3.427,1.125 1.885,0.292 10 false from Battery 0.979,1.406 2.865,1.698 1.885,0.292 10 false from IGR NO. 1 Relay 3.229,0.469 5.115,0.76 1.885,0.292 10 false ECU-DCC NO. 1 3.375,1.021 5.26,1.313 1.885,0.292 10 false P/SEAT F/R 3.281,1.604 4.396,1.833 1.115,0.229 10 false ECU-IGR NO. 1 4.844,0.302 5.333,0.531 0.49,0.229 10 false h24 4.833,1.417 5.323,1.646 0.49,0.229 10 false h24 6.417,0.792 6.906,1.021 0.49,0.229 10 false h22 4.823,2.25 5.313,2.479 0.49,0.229 10 false h24 4.844,0.073 5.333,0.302 0.49,0.229 10 false 15 4.885,0.625 5.375,0.854 0.49,0.229 10 false 3 4.885,1.167 5.375,1.396 0.49,0.229 10 false 1 4.854,2.01 5.344,2.24 0.49,0.229 10 false 12 5.25,0.302 5.896,0.583 0.646,0.281 10 false SYSB 5.25,0.865 5.896,1.146 0.646,0.281 10 false +B 5.25,1.438 5.896,1.719 0.646,0.281 10 false IG 5.25,2.25 5.896,2.531 0.646,0.281 10 false SGND 4.781,2.917 6.865,3.438 2.083,0.521 10 false Position Control ECU Assembly 1.271,2.646 2.229,2.927 0.958,0.281 10 false h7 1.271,2.813 3.646,3.052 2.375,0.24 10 false Front Power Seat Switch RH 2.74,2.156 3.229,2.385 0.49,0.229 10 false 11 4.833,0.854 5.323,1.083 0.49,0.229 10 false h22 6.479,0.542 6.969,0.771 0.49,0.229 10 false 2 5.969,0.802 6.615,1.083 0.646,0.281 10 false GND 2.51,2.25 3,2.479 0.49,0.229 10 false E


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FRONT POWER SEAT OPERATION

B

7.CHECK FRONT POWER SEAT OPERATION
2.CHECK FRONT POWER SEAT OPERATION
a.

Check that each function of the power seat operates normally by using the front power seat switch LH.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK


Result:
Result Proceed to
All power seat functions do not operate A
One or more power seat functions do not operate B



A

3.INSPECT FRONT POWER SEAT SWITCH LH

B

GO TO OTHER DIAGNOSIS PROCEDURE (One or more Power Seat Motors do not Operate)

3.INSPECT FRONT POWER SEAT SWITCH LH

OK

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - POWER SUPPLY)

NG

REPLACE FRONT POWER SEAT SWITCH LH

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - POWER SUPPLY)
a.

Disconnect the i17 and i19 position control ECU assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(i17,i19)Location & Routing

Click Connector(i17)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LH

Click Connector(i19)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LH

i17-3 (+B) - Body ground Always 11 to 14 V
i19-15 (SYSB) - Body ground Always 11 to 14 V
i19-1 (IG) - Body ground Ignition switch ON 11 to 14 V
i19-1 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - BODY GROUND)
a.

Disconnect the i17 position control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(i17)Location & Routing

Click Connector(i17)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LH

i17-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - POSITION CONTROL ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - POSITION CONTROL ECU ASSEMBLY)
a.

Disconnect the i14 front power seat switch LH connector.


b.

Disconnect the i17 position control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(i19,i14)Location & Routing

Click Connector(i19)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LH

Click Connector(i14)Seat>Front Seat Wire LH>Front Power Seat Switch LH

i19-12 (SGND) - i14-20 (E) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK FRONT POWER SEAT OPERATION
a.

Check that each function of the power seat operates normally by using the front power seat switch RH.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK


Result:
Result Proceed to
All power seat functions do not operate A
One or more power seat functions do not operate B



A

8.INSPECT FRONT POWER SEAT SWITCH RH

B

GO TO OTHER DIAGNOSIS PROCEDURE (One or more Power Seat Motors do not Operate)

8.INSPECT FRONT POWER SEAT SWITCH RH

OK

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - POWER SUPPLY)

NG

REPLACE FRONT POWER SEAT SWITCH RH

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - POWER SUPPLY)
a.

Disconnect the h22 and h24 position control ECU assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(h22,h24)Location & Routing

Click Connector(h22)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RH

Click Connector(h24)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RH

h22-3 (+B) - Body ground Always 11 to 14 V
h24-15 (SYSB) - Body ground Always 11 to 14 V
h24-1 (IG) - Body ground Ignition switch ON 11 to 14 V
h24-1 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - BODY GROUND)
a.

Disconnect the h22 position control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(h22)Location & Routing

Click Connector(h22)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RH

h22-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH RH - POSITION CONTROL ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH RH - POSITION CONTROL ECU ASSEMBLY)
a.

Disconnect the h7 front power seat switch RH connector.


b.

Disconnect the h24 position control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(h24,h7)Location & Routing

Click Connector(h24)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RH

Click Connector(h7)Seat>Front Seat Wire RH>Front Power Seat Switch RH

h24-12 (SGND) - h7-11 (E) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR