Signals are input into the position control ECU assembly. The built-in ECU manages the signals received from the position control ECU assembly and operates each motor. If the position control ECU assembly receives 2 or more operation signals for the same motor, the motor will be stopped. Manual operation resumes when the position control ECU assembly receives only 1 signal.
for LHD:
for RHD:
Initializing the position control ECU assembly will clear the seat position memory.
Make sure to initialize the position control ECU assembly after replacing the seat assembly or any related parts (including removal and installation).
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Check that each function of the power seat operates normally by using the front power seat switch LH.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK
| Result | Proceed to |
|---|---|
| One or more power seat functions do not operate | A |
| All power seat functions do not operate | B |
A
B
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Reclining Rear | Reclining switch signal (Rearward) | ON or OFF | ON: Reclining switch (Rearward) on OFF: Reclining switch (Rearward) off |
- |
| Reclining Front | Reclining switch signal (Forward) | ON or OFF | ON: Reclining switch (Forward) on OFF: Reclining switch (Forward) off |
- |
| Front Vertical Down | Front vertical switch signal (Downward) | ON or OFF | ON: Front vertical switch (Downward) on OFF: Front vertical switch (Downward) off |
- |
| Front Vertical Up | Front vertical switch signal (Upward) | ON or OFF | ON: Front vertical switch (Upward) on OFF: Front vertical switch (Upward) off |
- |
| Lifter Switch Down | Lifter switch signal (Downward) | ON or OFF | ON: Lifter switch (Downward) on OFF: Lifter switch (Downward) off |
- |
| Lifter Switch Up | Lifter switch signal (Upward) | ON or OFF | ON: Lifter switch (Upward) on OFF: Lifter switch (Upward) off |
- |
| Slide Rear | Slide switch signal (Rearward) | ON or OFF | ON: Slide switch (Rearward) on OFF: Slide switch (Rearward) off |
- |
| Slide Front | Slide switch signal (Forward) | ON or OFF | ON: Slide switch (Forward) on OFF: Slide switch (Forward) off |
- |
| Lumbar Switch Front | Lumbar support adjuster switch signal (Forward) | ON or OFF | ON: Lumbar support adjuster switch (Forward) on OFF: Lumbar support adjuster switch (Forward) off |
- |
| Lumbar Switch Rear | Lumbar support adjuster switch signal (Rearward) | ON or OFF | ON: Lumbar support adjuster switch (Rearward) on OFF: Lumbar support adjuster switch (Rearward) off |
- |
| Tester Display |
|---|
| Reclining Rear |
| Reclining Front |
| Front Vertical Down |
| Front Vertical Up |
| Lifter Switch Down |
| Lifter Switch Up |
| Slide Rear |
| Slide Front |
| Lumbar Switch Front |
| Lumbar Switch Rear |
On the GTS screen, ON or OFF is displayed accordingly
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Seat Reclining | Seat reclining operation | OFF/Rear/Front | - |
| Front Vertical Operation | Seat front vertical operation | OFF/Down/Up | - |
| Lifter Operation | Seat lifter operation | OFF/Down/Up | - |
| Seat Slide Operation | Seat slide operation | OFF/Rear/Front | - |
| Lumbar Slide | Lumbar support operation (Forward - Rearward) | OFF/Rear/Front | - |
| Tester Display |
|---|
| Seat Reclining |
| Tester Display |
|---|
| Front Vertical Operation |
| Tester Display |
|---|
| Lifter Operation |
| Tester Display |
|---|
| Seat Slide Operation |
| Tester Display |
|---|
| Lumbar Slide |
| Result | Proceed to |
|---|---|
| All power seat functions operate normally | A |
| Slide function does not operate normally | B |
| Front vertical function does not operate normally | C |
| Lifter function does not operate normally | D |
| Reclining function does not operate normally | E |
| Lumbar support adjustment function does not operate normally | F |
A
B
C
D
E
F
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT>LUMBAR SUPPORT ADJUSTER ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the i17 and i18 position control ECU assembly connectors.
Measure the resistance according to the value(s) in the table below.
Check the wire harness and connector between the position control ECU assembly and applicable motor.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(i17,i11)Location & Routingewd_type=routing;type=c,c;code=i17,i11 Click Connector(i17)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LHewd_type=component;type=c;code=i17;pinno=1,5 Click Connector(i11)Seat>Front Seat Wire LH>Power Seat Slide Motor LH (Front Seat Adjuster Assembly LH)ewd_type=component;type=c;code=i11;pinno=4,1 |
||
| i17-1 (SLD+) - i11-4 | Always | Below 1 Ω |
| i17-1 (SLD+) or i11-4 - Body ground | Always | 10 kΩ or higher |
| i17-5 (SLD-) - i11-1 | Always | Below 1 Ω |
| i17-5 (SLD-) or i11-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(i17,i12,i18)Location & Routingewd_type=routing;type=c,c,c;code=i17,i12,i18 Click Connector(i17)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LHewd_type=component;type=c;code=i17;pinno=7 Click Connector(i12)Seat>Front Seat Wire LH>Power Seat Tilt Motor LH (Front Seat Adjuster Assembly LH)ewd_type=component;type=c;code=i12;pinno=1,4 Click Connector(i18)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LHewd_type=component;type=c;code=i18;pinno=4 |
||
| i17-7 (FRV+) - i12-1 | Always | Below 1 Ω |
| i17-7 (FRV+) or i12-1 - Body ground | Always | 10 kΩ or higher |
| i18-4 (FRV-) - i12-4 | Always | Below 1 Ω |
| i18-4 (FRV-) or i12-4 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(i17,i13,i18)Location & Routingewd_type=routing;type=c,c,c;code=i17,i13,i18 Click Connector(i17)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LHewd_type=component;type=c;code=i17;pinno=6 Click Connector(i13)Seat>Front Seat Wire LH>Power Seat Lifter Motor LH (Front Seat Adjuster Assembly LH)ewd_type=component;type=c;code=i13;pinno=1,4 Click Connector(i18)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LHewd_type=component;type=c;code=i18;pinno=5 |
||
| i17-6 (LFT+) - i13-1 | Always | Below 1 Ω |
| i17-6 (LFT+) or i13-1 - Body ground | Always | 10 kΩ or higher |
| i18-5 (LFT-) - i13-4 | Always | Below 1 Ω |
| i18-5 (LFT-) or i13-4 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(i17,p3,i18)Location & Routingewd_type=routing;type=c,c,c;code=i17,p3,i18 Click Connector(i17)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LHewd_type=component;type=c;code=i17;pinno=10 Click Connector(p3)Seat>No. 2 Front Seat Wire LH>Front Power Seat Reclining Motor LHewd_type=component;type=c;code=p3;pinno=4,1 Click Connector(i18)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LHewd_type=component;type=c;code=i18;pinno=6 |
||
| i17-10 (RCL+) - p3-4 | Always | Below 1 Ω |
| i17-10 (RCL+) or p3-4 - Body ground | Always | 10 kΩ or higher |
| i18-6 (RCL-) - p3-1 | Always | Below 1 Ω |
| i18-6 (RCL-) or p3-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(i17,p4,i18)Location & Routingewd_type=routing;type=c,c,c;code=i17,p4,i18 Click Connector(i17)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LHewd_type=component;type=c;code=i17;pinno=9 Click Connector(p4)Seat>No. 2 Front Seat Wire LH>Front Power Seat Lumbar Support Motor LH (Lumbar Support Adjuster Assembly LH)ewd_type=component;type=c;code=p4;pinno=1,2 Click Connector(i18)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LHewd_type=component;type=c;code=i18;pinno=3 |
||
| i17-9 (L+) - p4-1 | Always | Below 1 Ω |
| i17-9 (L+) or p4-1 - Body ground | Always | 10 kΩ or higher |
| i18-3 (L-) - p4-2 | Always | Below 1 Ω |
| i18-3 (L-) or p4-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT>POWER SEAT SWITCH (for Front Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the i19 position control ECU assembly connector.
Disconnect the i14 front power seat switch LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(i14,i19)Location & Routingewd_type=routing;type=c,c;code=i14,i19 Click Connector(i14)Seat>Front Seat Wire LH>Front Power Seat Switch LHewd_type=component;type=c;code=i14;pinno=20 Click Connector(i19)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LHewd_type=component;type=c;code=i19;pinno=12 |
||
| i14-20 (E) - i19-12 (SGND) | Always | Below 1 Ω |
| i14-20 (E) or i19-12 (SGND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(i14,i19)Location & Routingewd_type=routing;type=c,c;code=i14,i19 Click Connector(i14)Seat>Front Seat Wire LH>Front Power Seat Switch LHewd_type=component;type=c;code=i14;pinno=6,7 Click Connector(i19)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LHewd_type=component;type=c;code=i19;pinno=23,9 |
||
| i14-6 (SLDR) - i19-23 (SLDR) | Always | Below 1 Ω |
| i14-6 (SLDR) or i19-23 (SLDR) - Body ground | Always | 10 kΩ or higher |
| i14-7 (SLDF) - i19-9 (SLDF) | Always | Below 1 Ω |
| i14-7 (SLDF) or i19-9 (SLDF) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(i14,i19)Location & Routingewd_type=routing;type=c,c;code=i14,i19 Click Connector(i14)Seat>Front Seat Wire LH>Front Power Seat Switch LHewd_type=component;type=c;code=i14;pinno=1,2 Click Connector(i19)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LHewd_type=component;type=c;code=i19;pinno=22,8 |
||
| i14-1 (RCLR) - i19-22 (RCLR) | Always | Below 1 Ω |
| i14-1 (RCLR) or i19-22 (RCLR) - Body ground | Always | 10 kΩ or higher |
| i14-2 (RCLF) - i19-8 (RCLF) | Always | Below 1 Ω |
| i14-2 (RCLF) or i19-8 (RCLF) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(i14,i19)Location & Routingewd_type=routing;type=c,c;code=i14,i19 Click Connector(i14)Seat>Front Seat Wire LH>Front Power Seat Switch LHewd_type=component;type=c;code=i14;pinno=4,5 Click Connector(i19)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LHewd_type=component;type=c;code=i19;pinno=6,20 |
||
| i14-4 (FUP) - i19-6 (FRVU) | Always | Below 1 Ω |
| i14-4 (FUP) or i19-6 (FRVU) - Body ground | Always | 10 kΩ or higher |
| i14-5 (FDWN) - i19-20 (FRVD) | Always | Below 1 Ω |
| i14-5 (FDWN) or i19-20 (FRVD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(i14,i19)Location & Routingewd_type=routing;type=c,c;code=i14,i19 Click Connector(i14)Seat>Front Seat Wire LH>Front Power Seat Switch LHewd_type=component;type=c;code=i14;pinno=3,8 Click Connector(i19)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LHewd_type=component;type=c;code=i19;pinno=7,21 |
||
| i14-3 (LUP) - i19-7 (LFTU) | Always | Below 1 Ω |
| i14-3 (LUP) or i19-7 (LFTU) - Body ground | Always | 10 kΩ or higher |
| i14-8 (LDWN) - i19-21 (LFTD) | Always | Below 1 Ω |
| i14-8 (LDWN) or i19-21 (LFTD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(i14,i19)Location & Routingewd_type=routing;type=c,c;code=i14,i19 Click Connector(i14)Seat>Front Seat Wire LH>Front Power Seat Switch LHewd_type=component;type=c;code=i14;pinno=17,14 Click Connector(i19)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LHewd_type=component;type=c;code=i19;pinno=18,4 |
||
| i14-17 (R) - i19-18 (LFLR) | Always | Below 1 Ω |
| i14-17 (R) or i19-18 (LFLR) - Body ground | Always | 10 kΩ or higher |
| i14-14 (H) - i19-4 (LFLF) | Always | Below 1 Ω |
| i14-14 (H) or i19-4 (LFLF) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that each function of the power seat operates normally by using the front power seat switch RH.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK
| Result | Proceed to |
|---|---|
| One or more power seat functions do not operate | A |
| All power seat functions do not operate | B |
A
B
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Reclining Rear | Reclining switch signal (Rearward) | ON or OFF | ON: Reclining switch (Rearward) on OFF: Reclining switch (Rearward) off |
- |
| Reclining Front | Reclining switch signal (Forward) | ON or OFF | ON: Reclining switch (Forward) on OFF: Reclining switch (Forward) off |
- |
| Front Vertical Down | Front vertical switch signal (Downward) | ON or OFF | ON: Front vertical switch (Downward) on OFF: Front vertical switch (Downward) off |
- |
| Front Vertical Up | Front vertical switch signal (Upward) | ON or OFF | ON: Front vertical switch (Upward) on OFF: Front vertical switch (Upward) off |
- |
| Lifter Switch Down | Lifter switch signal (Downward) | ON or OFF | ON: Lifter switch (Downward) on OFF: Lifter switch (Downward) off |
- |
| Lifter Switch Up | Lifter switch signal (Upward) | ON or OFF | ON: Lifter switch (Upward) on OFF: Lifter switch (Upward) off |
- |
| Slide Rear | Slide switch signal (Rearward) | ON or OFF | ON: Slide switch (Rearward) on OFF: Slide switch (Rearward) off |
- |
| Slide Front | Slide switch signal (Forward) | ON or OFF | ON: Slide switch (Forward) on OFF: Slide switch (Forward) off |
- |
| Lumbar Switch Front | Lumbar support adjuster switch signal (Forward) | ON or OFF | ON: Lumbar support adjuster switch (Forward) on OFF: Lumbar support adjuster switch (Forward) off |
- |
| Lumbar Switch Rear | Lumbar support adjuster switch signal (Rearward) | ON or OFF | ON: Lumbar support adjuster switch (Rearward) on OFF: Lumbar support adjuster switch (Rearward) off |
- |
| Tester Display |
|---|
| Reclining Rear |
| Reclining Front |
| Front Vertical Down |
| Front Vertical Up |
| Lifter Switch Down |
| Lifter Switch Up |
| Slide Rear |
| Slide Front |
| Lumbar Switch UP |
| Lumbar Switch Down |
| Lumbar Switch Front |
| Lumbar Switch Rear |
On the GTS screen, ON or OFF is displayed accordingly
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Seat Reclining | Seat reclining operation | OFF/Rear/Front | - |
| Front Vertical Operation | Seat front vertical operation | OFF/Down/Up | - |
| Lifter Operation | Seat lifter operation | OFF/Down/Up | - |
| Seat Slide Operation | Seat slide operation | OFF/Rear/Front | - |
| Lumbar Slide | Lumbar support operation (Forward - Rearward) | OFF/Rear/Front | - |
| Tester Display |
|---|
| Seat Reclining |
| Tester Display |
|---|
| Front Vertical Operation |
| Tester Display |
|---|
| Lifter Operation |
| Tester Display |
|---|
| Seat Slide Operation |
| Tester Display |
|---|
| Lumbar Slide |
| Result | Proceed to |
|---|---|
| All power seat functions operate normally | A |
| Slide function does not operate normally | B |
| Front vertical function does not operate normally | C |
| Lifter function does not operate normally | D |
| Reclining function does not operate normally | E |
| Lumbar support adjustment function does not operate normally | F |
A
B
C
D
E
F
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT>LUMBAR SUPPORT ADJUSTER ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the h22 and h23 position control ECU assembly connectors.
Measure the resistance according to the value(s) in the table below.
Check the wire harness and connector between the position control ECU assembly and applicable motor.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(h22,h1)Location & Routingewd_type=routing;type=c,c;code=h22,h1 Click Connector(h22)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RHewd_type=component;type=c;code=h22;pinno=1,5 Click Connector(h1)Seat>Front Seat Wire RH>Power Seat Slide Motor RH (Front Seat Adjuster Assembly RH)ewd_type=component;type=c;code=h1;pinno=4,1 |
||
| h22-1 (SLD+) - h1-4 | Always | Below 1 Ω |
| h22-1 (SLD+) or h1-4 - Body ground | Always | 10 kΩ or higher |
| h22-5 (SLD-) - h1-1 | Always | Below 1 Ω |
| h22-5 (SLD-) or h1-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(h22,h2,h23)Location & Routingewd_type=routing;type=c,c,c;code=h22,h2,h23 Click Connector(h22)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RHewd_type=component;type=c;code=h22;pinno=7 Click Connector(h2)Seat>Front Seat Wire RH>Power Seat Tilt Motor RH (Front Seat Adjuster Assembly RH)ewd_type=component;type=c;code=h2;pinno=1,4 Click Connector(h23)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RHewd_type=component;type=c;code=h23;pinno=4 |
||
| h22-7 (FRV+) - h2-1 | Always | Below 1 Ω |
| h22-7 (FRV+) or h2-1 - Body ground | Always | 10 kΩ or higher |
| h23-4 (FRV-) - h2-4 | Always | Below 1 Ω |
| h23-4 (FRV-) or h2-4 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(h22,h3,h23)Location & Routingewd_type=routing;type=c,c,c;code=h22,h3,h23 Click Connector(h22)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RHewd_type=component;type=c;code=h22;pinno=6 Click Connector(h3)Seat>Front Seat Wire RH>Power Seat Lifter Motor RH (Front Seat Adjuster Assembly RH)ewd_type=component;type=c;code=h3;pinno=1,4 Click Connector(h23)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RHewd_type=component;type=c;code=h23;pinno=5 |
||
| h22-6 (LFT+) - h3-1 | Always | Below 1 Ω |
| h22-6 (LFT+) or h3-1 - Body ground | Always | 10 kΩ or higher |
| h23-5 (LFT-) - h3-4 | Always | Below 1 Ω |
| h23-5 (LFT-) or h3-4 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(h22,o4,h23)Location & Routingewd_type=routing;type=c,c,c;code=h22,o4,h23 Click Connector(h22)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RHewd_type=component;type=c;code=h22;pinno=10 Click Connector(o4)Seat>No. 2 Front Seat Wire RH>Front Power Seat Reclining Motor RHewd_type=component;type=c;code=o4;pinno=4,1 Click Connector(h23)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RHewd_type=component;type=c;code=h23;pinno=6 |
||
| h22-10 (RCL+) - o4-4 | Always | Below 1 Ω |
| h22-10 (RCL+) or o4-4 - Body ground | Always | 10 kΩ or higher |
| h23-6 (RCL-) - o4-1 | Always | Below 1 Ω |
| h23-6 (RCL-) or o4-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(h22,o3,h23)Location & Routingewd_type=routing;type=c,c,c;code=h22,o3,h23 Click Connector(h22)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RHewd_type=component;type=c;code=h22;pinno=9 Click Connector(o3)Seat>No. 2 Front Seat Wire RH>Front Power Seat Lumbar Support Motor RH (Lumbar Support Adjuster Assembly RH)ewd_type=component;type=c;code=o3;pinno=1,2 Click Connector(h23)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RHewd_type=component;type=c;code=h23;pinno=3 |
||
| h22-9 (L+) - o3-1 | Always | Below 1 Ω |
| h22-9 (L+) or o3-1 - Body ground | Always | 10 kΩ or higher |
| h23-3 (L-) - o3-2 | Always | Below 1 Ω |
| h23-3 (L-) or o3-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT>POWER SEAT SWITCH (for Front Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the h24 position control ECU assembly connector.
Disconnect the h7 front power seat switch RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(h7,h24)Location & Routingewd_type=routing;type=c,c;code=h7,h24 Click Connector(h7)Seat>Front Seat Wire RH>Front Power Seat Switch RHewd_type=component;type=c;code=h7;pinno=11 Click Connector(h24)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RHewd_type=component;type=c;code=h24;pinno=12 |
||
| h7-11 (E) - h24-12 (SGND) | Always | Below 1 Ω |
| h7-11 (E) or h24-12 (SGND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(h7,h24)Location & Routingewd_type=routing;type=c,c;code=h7,h24 Click Connector(h7)Seat>Front Seat Wire RH>Front Power Seat Switch RHewd_type=component;type=c;code=h7;pinno=5,4 Click Connector(h24)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RHewd_type=component;type=c;code=h24;pinno=23,9 |
||
| h7-5 (SLDR) - h24-23 (SLDR) | Always | Below 1 Ω |
| h7-5 (SLDR) or h24-23 (SLDR) - Body ground | Always | 10 kΩ or higher |
| h7-4 (SLDF) - h24-9 (SLDF) | Always | Below 1 Ω |
| h7-4 (SLDF) or h24-9 (SLDF) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(h7,h24)Location & Routingewd_type=routing;type=c,c;code=h7,h24 Click Connector(h7)Seat>Front Seat Wire RH>Front Power Seat Switch RHewd_type=component;type=c;code=h7;pinno=10,9 Click Connector(h24)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RHewd_type=component;type=c;code=h24;pinno=22,8 |
||
| h7-10 (RCLR) - h24-22 (RCLR) | Always | Below 1 Ω |
| h7-10 (RCLR) or h24-22 (RCLR) - Body ground | Always | 10 kΩ or higher |
| h7-9 (RCLF) - h24-8 (RCLF) | Always | Below 1 Ω |
| h7-9 (RCLF) or h24-8 (RCLF) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(h7,h24)Location & Routingewd_type=routing;type=c,c;code=h7,h24 Click Connector(h7)Seat>Front Seat Wire RH>Front Power Seat Switch RHewd_type=component;type=c;code=h7;pinno=7,6 Click Connector(h24)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RHewd_type=component;type=c;code=h24;pinno=6,20 |
||
| h7-7 (FUP) - h24-6 (FRVU) | Always | Below 1 Ω |
| h7-7 (FUP) or h24-6 (FRVU) - Body ground | Always | 10 kΩ or higher |
| h7-6 (FDWN) - h24-20 (FRVD) | Always | Below 1 Ω |
| h7-6 (FDWN) or h24-20 (FRVD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(h7,h24)Location & Routingewd_type=routing;type=c,c;code=h7,h24 Click Connector(h7)Seat>Front Seat Wire RH>Front Power Seat Switch RHewd_type=component;type=c;code=h7;pinno=8,3 Click Connector(h24)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RHewd_type=component;type=c;code=h24;pinno=7,21 |
||
| h7-8 (LUP) - h24-7 (LFTU) | Always | Below 1 Ω |
| h7-8 (LUP) or h24-7 (LFTU) - Body ground | Always | 10 kΩ or higher |
| h7-3 (LDWN) - h24-21 (LFTD) | Always | Below 1 Ω |
| h7-3 (LDWN) or h24-21 (LFTD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(h7,h24)Location & Routingewd_type=routing;type=c,c;code=h7,h24 Click Connector(h7)Seat>Front Seat Wire RH>Front Power Seat Switch RHewd_type=component;type=c;code=h7;pinno=14,17 Click Connector(h24)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RHewd_type=component;type=c;code=h24;pinno=18,4 |
||
| h7-14 (R) - h24-18 (LFLR) | Always | Below 1 Ω |
| h7-14 (R) or h24-18 (LFLR) - Body ground | Always | 10 kΩ or higher |
| h7-17 (H) - h24-4 (LFLF) | Always | Below 1 Ω |
| h7-17 (H) or h24-4 (LFLF) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG