Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM38G0E _58 Vehicle Interior _100628 SEAT _0467514 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2651  Reclining Sensor Malfunction  


DESCRIPTION

When the position control ECU assembly does not receive a reclining motor position sensor signal despite the seat having been moved forward or rearward by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2651 Reclining Sensor Malfunction Reclining motor position sensor signal not received when power seat moved forward or rearward
·

Position control ECU assembly

·

Reclining motor (front seatback frame sub-assembly LH) (for LHD)

·

Reclining motor (front seatback frame sub-assembly RH) (for RHD)

·

Harness or connector


Driver Seat A

WIRING DIAGRAM

for LHD:


B591059E07
1.146,2.49 2.219,2.708 1.073,0.219 10 false p3 4.854,1.063 5.313,1.26 0.458,0.198 10 false i18 4.833,0.542 5.292,0.74 0.458,0.198 10 false i17 4.833,2.104 5.292,2.302 0.458,0.198 10 false i19 4.833,1.573 5.292,1.771 0.458,0.198 10 false i19 5.229,0.542 5.844,0.74 0.615,0.198 10 false RCL+ 5.219,1.052 5.833,1.25 0.615,0.198 10 false RCL- 5.229,1.563 5.844,1.76 0.615,0.198 10 false SSRR 5.229,2.083 5.844,2.281 0.615,0.198 10 false SGND 1.146,2.688 2.833,2.885 1.688,0.198 10 false Reclining Motor 4.75,2.615 6.99,2.979 2.24,0.365 10 false Position Control ECU Assembly 0.333,3.083 3.083,3.323 2.75,0.24 10 false Front Seatback Frame Sub-assembly LH 4.844,0.313 5.052,0.521 0.208,0.208 10 false 10 4.896,0.823 5.052,1.021 0.156,0.198 10 false 6 4.844,1.333 5.156,1.531 0.313,0.198 10 false 11 4.833,1.844 5.146,2.042 0.313,0.198 10 false 12 2.333,1.448 3.01,1.698 0.677,0.25 10 false 2 2.333,0.427 2.948,0.708 0.615,0.281 10 false 4 2.323,0.948 3.052,1.188 0.729,0.24 10 false 1 2.333,1.969 3.146,2.271 0.813,0.302 10 false 3


for RHD:


B591059E08
1.146,2.49 2.219,2.708 1.073,0.219 10 false o4 4.833,1.063 5.292,1.26 0.458,0.198 10 false h23 4.833,0.542 5.292,0.74 0.458,0.198 10 false h22 4.833,2.104 5.292,2.302 0.458,0.198 10 false h24 4.833,1.573 5.292,1.771 0.458,0.198 10 false h24 5.229,0.542 5.844,0.74 0.615,0.198 10 false RCL+ 5.219,1.052 5.833,1.25 0.615,0.198 10 false RCL- 5.229,1.563 5.844,1.76 0.615,0.198 10 false SSRR 5.229,2.083 5.844,2.281 0.615,0.198 10 false SGND 1.146,2.688 2.833,2.885 1.688,0.198 10 false Reclining Motor 4.75,2.615 7.021,3.01 2.271,0.396 10 false Position Control ECU Assembly 0.333,3.083 3.208,3.406 2.875,0.323 10 false Front Seatback Frame Sub-assembly RH 4.844,0.313 5.052,0.521 0.208,0.208 10 false 10 4.896,0.823 5.052,1.021 0.156,0.198 10 false 6 4.844,1.333 5.156,1.531 0.313,0.198 10 false 11 4.833,1.844 5.146,2.042 0.313,0.198 10 false 12 2.333,1.448 3.01,1.698 0.677,0.25 10 false 2 2.333,0.427 2.948,0.708 0.615,0.281 10 false 4 2.323,0.948 3.052,1.188 0.729,0.24 10 false 1 2.333,1.969 3.146,2.271 0.813,0.302 10 false 3


CAUTION / NOTICE / HINT

NOTICE:

Initializing the position control ECU assembly will clear the seat position memory.


HINT:

Make sure to initialize the position control ECU assembly after replacing the seat assembly or any related parts (including removal and installation).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>REGISTRATION


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CLEAR DTC

B

10.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162

Result:
Result Proceed to
B2651 is not output A
B2651 is output B



A

B

4.PERFORM ACTIVE TEST USING GTS (SEAT RECLINING OPERATION)
4.PERFORM ACTIVE TEST USING GTS (SEAT RECLINING OPERATION)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Reclining Seat reclining operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Reclining
50004 162 1
OK:

Reclining motor operates normally.



Result:
Proceed to
OK
NG



OK

5.CHECK POSITION CONTROL ECU ASSEMBLY (RECLINING MOTOR CIRCUIT)

NG

8.INSPECT RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY LH)
5.CHECK POSITION CONTROL ECU ASSEMBLY (RECLINING MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the p3 reclining motor (front seatback frame sub-assembly LH) connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(p3)Location & Routing

Click Connector(p3)Seat>No. 2 Front Seat Wire LH>Front Power Seat Reclining Motor LH

p3-2 - p3-3 Reclining switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

6.CHECK RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY LH)

NG

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY LH))
6.CHECK RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY LH)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(p3)Location & Routing

Click Connector(p3)Seat>No. 2 Front Seat Wire LH>Front Power Seat Reclining Motor LH

p3-2 - Body ground Reclining motor operating 4.5 to 4.8 V


Result:
Proceed to
OK
NG




OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPLACE RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY LH)

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY LH))

Pre-procedure1

a.

Disconnect the i19 position control ECU assembly connector.


b.

Disconnect the p3 reclining motor (front seatback frame sub-assembly LH) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(i19,p3)Location & Routing

Click Connector(i19)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LH

Click Connector(p3)Seat>No. 2 Front Seat Wire LH>Front Power Seat Reclining Motor LH

i19-11 (SSRR) - p3-2 Always Below 1 Ω
i19-11 (SSRR) or p3-2 - Body ground Always 10 kΩ or higher
i19-12 (SGND) - p3-3 Always Below 1 Ω
i19-12 (SGND) or p3-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY LH)

OK

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY LH))

NG

REPLACE RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY LH)

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY LH))

Pre-procedure1

a.

Disconnect the i17 and i18 position control ECU assembly connectors.


b.

Disconnect the p3 reclining motor (front seatback frame sub-assembly LH) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(i17,p3,i18)Location & Routing

Click Connector(i17)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LH

Click Connector(p3)Seat>No. 2 Front Seat Wire LH>Front Power Seat Reclining Motor LH

Click Connector(i18)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LH

i17-10 (RCL+) - p3-4 Always Below 1 Ω
i17-10 (RCL+) or p3-4 - Body ground Always 10 kΩ or higher
i18-6 (RCL-) - p3-1 Always Below 1 Ω
i18-6 (RCL-) or p3-1 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162

Result:
Result Proceed to
B2651 is not output A
B2651 is output B



A

B

12.PERFORM ACTIVE TEST USING GTS (SEAT RECLINING OPERATION)
12.PERFORM ACTIVE TEST USING GTS (SEAT RECLINING OPERATION)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Reclining Seat reclining operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Reclining
50004 162 1
OK:

Reclining motor operates normally.



Result:
Proceed to
OK
NG



OK

13.CHECK POSITION CONTROL ECU ASSEMBLY (RECLINING MOTOR CIRCUIT)

NG

16.INSPECT RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY RH)
13.CHECK POSITION CONTROL ECU ASSEMBLY (RECLINING MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the o4 reclining motor (front seatback frame sub-assembly RH) connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(o4)Location & Routing

Click Connector(o4)Seat>No. 2 Front Seat Wire RH>Front Power Seat Reclining Motor RH

o4-2 - o4-3 Reclining switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

14.CHECK RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY RH)

NG

15.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY RH))
14.CHECK RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY RH)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(o4)Location & Routing

Click Connector(o4)Seat>No. 2 Front Seat Wire RH>Front Power Seat Reclining Motor RH

o4-2 - Body ground Reclining motor operating 4.5 to 4.8 V


Result:
Proceed to
OK
NG




OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPLACE RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY RH)

15.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY RH))

Pre-procedure1

a.

Disconnect the h24 position control ECU assembly connector.


b.

Disconnect the o4 reclining motor (front seatback frame sub-assembly RH) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(h24,o4)Location & Routing

Click Connector(h24)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RH

Click Connector(o4)Seat>No. 2 Front Seat Wire RH>Front Power Seat Reclining Motor RH

h24-11 (SSRR) - o4-2 Always Below 1 Ω
h24-11 (SSRR) or o4-2 - Body ground Always 10 kΩ or higher
h24-12 (SGND) - o4-3 Always Below 1 Ω
h24-12 (SGND) or o4-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY RH)

OK

17.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY RH))

NG

REPLACE RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY RH)

17.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY RH))

Pre-procedure1

a.

Disconnect the h22 and h23 position control ECU assembly connectors.


b.

Disconnect the o4 reclining motor (front seatback frame sub-assembly RH) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(h22,o4,h23)Location & Routing

Click Connector(h22)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RH

Click Connector(o4)Seat>No. 2 Front Seat Wire RH>Front Power Seat Reclining Motor RH

Click Connector(h23)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RH

h22-10 (RCL+) - o4-4 Always Below 1 Ω
h22-10 (RCL+) or o4-4 - Body ground Always 10 kΩ or higher
h23-6 (RCL-) - o4-1 Always Below 1 Ω
h23-6 (RCL-) or o4-1 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR