Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM38G0E _58 Vehicle Interior _100628 SEAT _0467514 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2653  Lifter Sensor Malfunction  


DESCRIPTION

When the position control ECU assembly does not receive a lifter motor position sensor signal despite the seat having been moved upward or downward by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2653 Lifter Sensor Malfunction Lifter motor position sensor signal not received when power seat moved upward or downward
·

Position control ECU assembly

·

Lifter motor (front seat adjuster assembly LH) (for LHD)

·

Lifter motor (front seat adjuster assembly LH RH) (for RHD)

·

Harness or connector


Driver Seat A

WIRING DIAGRAM

for LHD:


B591059E12
0.844,2.458 1.958,2.74 1.115,0.281 10 false i13 4.813,1.063 5.271,1.26 0.458,0.198 10 false i18 4.833,0.542 5.292,0.74 0.458,0.198 10 false i17 4.854,2.083 5.313,2.281 0.458,0.198 10 false i19 4.844,1.573 5.302,1.771 0.458,0.198 10 false i19 5.229,0.542 5.844,0.74 0.615,0.198 10 false LFT+ 5.229,1.052 5.844,1.25 0.615,0.198 10 false LFT- 5.229,1.563 5.844,1.76 0.615,0.198 10 false SSFV 5.229,2.083 5.844,2.281 0.615,0.198 10 false SGND 0.875,2.635 2.677,2.813 1.802,0.177 10 false Lifter Motor 4.75,2.604 7.042,2.938 2.292,0.333 10 false Position Control ECU Assembly 4.885,0.302 5.073,0.531 0.188,0.229 10 false 6 4.885,0.833 5.063,1.104 0.177,0.271 10 false 5 4.844,1.333 5.156,1.531 0.313,0.198 10 false 25 4.844,1.854 5.156,2.052 0.313,0.198 10 false 12 2.333,1.479 2.521,1.719 0.188,0.24 10 false 2 2.323,0.448 2.677,0.656 0.354,0.208 10 false 1 2.323,0.969 2.667,1.177 0.344,0.208 10 false 4 2.323,1.99 2.573,2.229 0.25,0.24 10 false 3 0.531,3.083 2.729,3.708 2.198,0.625 10 false Front Seat Adjuster Assembly LH


for RHD:


B591059E13
0.917,2.5 2.031,2.781 1.115,0.281 10 false h3 4.813,1.063 5.271,1.26 0.458,0.198 10 false h23 4.833,0.542 5.292,0.74 0.458,0.198 10 false h22 4.854,2.083 5.313,2.281 0.458,0.198 10 false h24 4.844,1.573 5.302,1.771 0.458,0.198 10 false h24 5.229,0.542 5.844,0.74 0.615,0.198 10 false LFT+ 5.229,1.052 5.844,1.25 0.615,0.198 10 false LFT- 5.229,1.563 5.844,1.76 0.615,0.198 10 false SSFV 5.229,2.083 5.844,2.281 0.615,0.198 10 false SGND 0.26,3.094 2.969,3.677 2.708,0.583 10 false Front Seat Adjuster Assembly RH 4.698,2.604 6.958,3.031 2.26,0.427 10 false Position Control ECU Assembly 4.885,0.302 5.073,0.531 0.188,0.229 10 false 6 4.885,0.833 5.063,1.104 0.177,0.271 10 false 5 4.844,1.333 5.156,1.531 0.313,0.198 10 false 25 4.844,1.854 5.156,2.052 0.313,0.198 10 false 12 2.333,1.479 2.521,1.719 0.188,0.24 10 false 2 2.323,0.448 2.677,0.656 0.354,0.208 10 false 1 2.323,0.969 2.667,1.177 0.344,0.208 10 false 4 2.323,1.99 2.573,2.229 0.25,0.24 10 false 3 0.927,2.688 2.969,3.396 2.042,0.708 10 false Lifter Motor


CAUTION / NOTICE / HINT

NOTICE:

Initializing the position control ECU assembly will clear the seat position memory.


HINT:

Make sure to initialize the position control ECU assembly after replacing the seat assembly or any related parts (including removal and installation).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>REGISTRATION


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CLEAR DTC

B

10.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162

Result:
Result Proceed to
B2653 is not output A
B2653 is output B



A

B

4.PERFORM ACTIVE TEST USING GTS (SEAT LIFTER OPERATION)
4.PERFORM ACTIVE TEST USING GTS (SEAT LIFTER OPERATION)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Lifter Operation Seat lifter operation OFF/Down/Up -
Body Electrical > Driver Seat > Active Test
Tester Display
Lifter Operation
50004 162 2
OK:

Lifter motor operates normally.



Result:
Proceed to
OK
NG



OK

5.CHECK POSITION CONTROL ECU ASSEMBLY (LIFTER MOTOR CIRCUIT)

NG

8.INSPECT LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH)
5.CHECK POSITION CONTROL ECU ASSEMBLY (LIFTER MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the i13 lifter motor (front seat adjuster assembly LH) connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(i13)Location & Routing

Click Connector(i13)Seat>Front Seat Wire LH>Power Seat Lifter Motor LH (Front Seat Adjuster Assembly LH)

i13-2 - i13-3 Lifter switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

6.CHECK LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH)

NG

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH))
6.CHECK LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(i13)Location & Routing

Click Connector(i13)Seat>Front Seat Wire LH>Power Seat Lifter Motor LH (Front Seat Adjuster Assembly LH)

i13-2 - Body ground Lifter motor operating 4.5 to 4.8 V


Result:
Proceed to
OK
NG




OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPLACE LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH)

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH))

Pre-procedure1

a.

Disconnect the i19 position control ECU assembly connector.


b.

Disconnect the i13 lifter motor (front seat adjuster assembly LH) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(i19,i13)Location & Routing

Click Connector(i19)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LH

Click Connector(i13)Seat>Front Seat Wire LH>Power Seat Lifter Motor LH (Front Seat Adjuster Assembly LH)

i19-25 (SSRL) - i13-2 Always Below 1 Ω
i19-25 (SSRL) or i13-2 - Body ground Always 10 kΩ or higher
i19-12 (SGND) - i13-3 Always Below 1 Ω
i19-12 (SGND) or i13-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH)

OK

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH))

NG

REPLACE LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH)

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH))

Pre-procedure1

a.

Disconnect the i17 and i18 position control ECU assembly connectors.


b.

Disconnect the i13 lifter motor (front seat adjuster assembly LH) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(i17,i13,i18)Location & Routing

Click Connector(i17)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LH

Click Connector(i13)Seat>Front Seat Wire LH>Power Seat Lifter Motor LH (Front Seat Adjuster Assembly LH)

Click Connector(i18)Seat>Front Seat Wire LH>Front Position Control ECU Assembly LH

i17-6 (LFT+) - i13-1 Always Below 1 Ω
i17-6 (LFT+) or i13-1 - Body ground Always 10 kΩ or higher
i18-5 (LFT-) - i13-4 Always Below 1 Ω
i18-5 (LFT-) or i13-4 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162

Result:
Result Proceed to
B2653 is not output A
B2653 is output B



A

B

12.PERFORM ACTIVE TEST USING GTS (SEAT LIFTER OPERATION)
12.PERFORM ACTIVE TEST USING GTS (SEAT LIFTER OPERATION)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Lifter Operation Seat lifter operation OFF/Down/Up -
Body Electrical > Driver Seat > Active Test
Tester Display
Lifter Operation
50004 162 2
OK:

Lifter motor operates normally.



Result:
Proceed to
OK
NG



OK

13.CHECK POSITION CONTROL ECU ASSEMBLY (LIFTER MOTOR CIRCUIT)

NG

16.INSPECT LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY RH)
13.CHECK POSITION CONTROL ECU ASSEMBLY (LIFTER MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the h3 lifter motor (front seat adjuster assembly RH) connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(h3)Location & Routing

Click Connector(h3)Seat>Front Seat Wire RH>Power Seat Lifter Motor RH (Front Seat Adjuster Assembly RH)

h3-2 - h3-3 Lifter switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

14.CHECK LIFTER MOTOR (POWER SEAT LIFTER MOTOR ASSEMBLY RH)

NG

15.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY RH))
14.CHECK LIFTER MOTOR (POWER SEAT LIFTER MOTOR ASSEMBLY RH)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(h3)Location & Routing

Click Connector(h3)Seat>Front Seat Wire RH>Power Seat Lifter Motor RH (Front Seat Adjuster Assembly RH)

h3-2 - Body ground Lifter motor operating 4.5 to 4.8 V


Result:
Proceed to
OK
NG




OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPLACE LIFTER MOTOR (POWER SEAT LIFTER MOTOR ASSEMBLY RH)

15.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY RH))

Pre-procedure1

a.

Disconnect the h24 position control ECU assembly connector.


b.

Disconnect the h3 lifter motor (front seat adjuster assembly RH) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(h24,h3)Location & Routing

Click Connector(h24)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RH

Click Connector(h3)Seat>Front Seat Wire RH>Power Seat Lifter Motor RH (Front Seat Adjuster Assembly RH)

h24-25 (SSRL) - h3-2 Always Below 1 Ω
h24-25 (SSRL) or h3-2 - Body ground Always 10 kΩ or higher
h24-12 (SGND) - h3-3 Always Below 1 Ω
h24-12 (SGND) or h3-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY RH)

OK

17.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY RH))

NG

REPLACE LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY RH)

17.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY RH))

Pre-procedure1

a.

Disconnect the h3 lifter motor (front seat adjuster assembly RH) connector.


b.

Disconnect the h22 and h23 position control ECU assembly connectors.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(h22,h3,h23)Location & Routing

Click Connector(h22)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RH

Click Connector(h3)Seat>Front Seat Wire RH>Power Seat Lifter Motor RH (Front Seat Adjuster Assembly RH)

Click Connector(h23)Seat>Front Seat Wire RH>Front Position Control ECU Assembly RH

h22-6 (LFT+) - h3-1 Always Below 1 Ω
h22-6 (LFT+) or h3-1 - Body ground Always 10 kΩ or higher
h23-5 (LFT-) - h3-4 Always Below 1 Ω
h23-5 (LFT-) or h3-4 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR