Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR SEAT ENTERTAINMENT SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467498 REAR SEAT ENTERTAINMENT SYSTEM J

AUDIO / VIDEO  REAR SEAT ENTERTAINMENT SYSTEM  Visual Mute Signal Circuit between Multi-display Controller and Television Display Assembly  


DESCRIPTION

This is the visual mute signal circuit from the multi-display controller to each television display assembly.

WIRING DIAGRAM

E248928E24
1.969,2.167 2.177,2.323 0.208,0.156 10 false 2 1.969,0.646 2.177,0.802 0.208,0.156 10 false 2 5.594,0.781 6.406,0.927 0.813,0.146 10 false VMT1 5.583,2.281 6.323,2.427 0.74,0.146 10 false VMT2 1.094,1.375 3.677,1.667 2.583,0.292 10 false Television Display Assembly RH 1.094,1.219 1.469,1.406 0.375,0.188 10 false q1 1.094,2.906 3.177,3.188 2.083,0.281 10 false Television Display Assembly LH 5.198,2.854 6.75,3.188 1.552,0.333 10 false Multi-display Controller 1.094,2.729 1.469,2.979 0.375,0.25 10 false q4 5.198,2.667 5.573,2.854 0.375,0.188 10 false Q30 5.417,0.708 5.625,0.865 0.208,0.156 10 false 4 5.365,2.208 5.573,2.365 0.208,0.156 10 false 5 1.479,0.771 1.927,0.958 0.448,0.188 10 false VMTR 1.458,2.302 1.906,2.49 0.448,0.188 10 false VMTR

PROCEDURE

1.CHECK MULTI-DISPLAY CONTROLLER
a.
E249383C20
0.167,1 0.583,1.25 0.417,0.25 1.115,1.021 1.5,0.667 true 0.969,1.021 0.583,0.667 true 0.198,0.146 0.51,0.302 0.313,0.156 10 false *a 1.354,0.479 1.99,0.646 0.635,0.167 10 false VMT1 0.365,0.479 1,0.646 0.635,0.167 10 false VMT2 0.25,1.052 0.604,1.219 0.354,0.167 10 false Q30
*a Component with harness connected
(Multi-display Controller)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(Q30)Location & Routing

Click Connector(Q30)Seat>Floor Wire>Multi-Display Controller

Q30-5 (VMT2) - Body ground RSE playing → Source changed Higher than 3.5 V → Below 1 V
Q30-4 (VMT1) - Body ground RSE playing → Source changed Higher than 3.5 V → Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER - TELEVISION DISPLAY ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER - TELEVISION DISPLAY ASSEMBLY)
a.

Disconnect the Q30 multi-display controller connector.


b.

Disconnect the q4 television display assembly LH connector.


c.

Disconnect the L142 television display assembly RH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q30,q4,q1)Location & Routing

Click Connector(Q30)Seat>Floor Wire>Multi-Display Controller

Click Connector(q4)Seat>Seat Audio Wire>Television Display Assembly LH

Click Connector(q1)Seat>Seat Audio Wire>Television Display Assembly RH

Q30-5 (VMT2) - q4-2 (VMTR) Always Below 1 Ω
Q30-4 (VMT1) - q1-2 (VMTR) Always Below 1 Ω
Q30-5 (VMT2) - Body ground Always 10 kΩ or higher
Q30-4 (VMT1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK MULTI-DISPLAY CONTROLLER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MULTI-DISPLAY CONTROLLER
a.

Disconnect the Q30 multi-display controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition

Click Location & Routing(Q30)Location & Routing

Click Connector(Q30)Seat>Floor Wire>Multi-Display Controller

Q30-4 (VMT1) - Body ground Television display assembly ON Higher than 3.5 V

for LH
Tester Connection Condition Specified Condition

Click Location & Routing(Q30)Location & Routing

Click Connector(Q30)Seat>Floor Wire>Multi-Display Controller

Q30-5 (VMT2) - Body ground Television display assembly ON Higher than 3.5 V



Result:
Result Proceed to
OK A
NG (for RH) B
NG (for LH) C



A

B

REPLACE TELEVISION DISPLAY ASSEMBLY RH

C

REPLACE TELEVISION DISPLAY ASSEMBLY LH