Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR SEAT ENTERTAINMENT SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467498 REAR SEAT ENTERTAINMENT SYSTEM J

AUDIO / VIDEO  REAR SEAT ENTERTAINMENT SYSTEM  Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the multi-display controller, television display assembly.

WIRING DIAGRAM

E462671E02
5.052,2.031 5.521,2.25 0.469,0.219 10 false Q29 0.844,0.615 3.594,0.813 2.75,0.198 10 false from Battery 2.156,0.854 2.99,1.052 0.833,0.198 10 false RADIO 5.031,2.188 6.781,2.531 1.75,0.344 10 false Multi-display Controller 5.135,0.615 5.604,0.833 0.469,0.219 10 false +B 4.865,0.51 5.333,0.729 0.469,0.219 10 false 1 5.146,1.583 5.615,1.802 0.469,0.219 10 false GND 4.844,1.417 5.313,1.635 0.469,0.219 10 false 14 5.021,6.208 5.49,6.427 0.469,0.219 10 false q4 4.979,4.146 7.073,4.5 2.094,0.354 10 false Television Display Assembly RH 5,3.958 5.469,4.177 0.469,0.219 10 false q1 4.979,6.365 7.073,6.719 2.094,0.354 10 false Television Display Assembly LH 2.156,3.219 2.99,3.417 0.833,0.198 10 false RSE DISP 0.833,2.99 1.979,3.219 1.146,0.229 10 false from Battery 4.823,2.906 5.292,3.125 0.469,0.219 10 false 6 4.771,3.396 5.24,3.615 0.469,0.219 10 false 10 5.135,3.042 5.604,3.26 0.469,0.219 10 false +B 5.115,3.521 5.583,3.74 0.469,0.219 10 false GND4 5.135,5.292 5.604,5.51 0.469,0.219 10 false +B 5.156,5.781 5.625,6 0.469,0.219 10 false GND4 4.844,5.125 5.313,5.344 0.469,0.219 10 false 6 4.823,5.625 5.292,5.844 0.469,0.219 10 false 10

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK OPERATION
a.

Check which television display assembly does not operate.

Result:
Result Proceed to
Television display assembly RH does not operate. A
Television display assembly LH does not operate. B
Multi-display controller does not operate. C




A

2.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY RH - BATTERY AND BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY LH - BATTERY AND BODY GROUND)

C

4.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY RH - BATTERY AND BODY GROUND)
a.

Disconnect the q1 television display assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(q1)Location & Routing

Click Connector(q1)Seat>Seat Audio Wire>Television Display Assembly RH

q1-6 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(q1)Location & Routing

Click Connector(q1)Seat>Seat Audio Wire>Television Display Assembly RH

q1-10 (GND4) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY LH - BATTERY AND BODY GROUND)
a.

Disconnect the q4 television display assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(q4)Location & Routing

Click Connector(q4)Seat>Seat Audio Wire>Television Display Assembly LH

q4-6 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(q4)Location & Routing

Click Connector(q4)Seat>Seat Audio Wire>Television Display Assembly LH

q4-10 (GND4) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER - BATTERY AND BODY GROUND)
a.

Disconnect the Q29 multi-display controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(Q29)Location & Routing

Click Connector(Q29)Seat>Floor Wire>Multi-Display Controller

Q29-1 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q29)Location & Routing

Click Connector(Q29)Seat>Floor Wire>Multi-Display Controller

Q29-14 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR