Home › Engine / Hybrid System › V35A-FTS (ENGINE MECHANICAL) › CYLINDER HEAD
RM38G0E _51 Engine / Hybrid System _100652 V35A-FTS ENGINE MECHANICAL _0467576 CYLINDER HEAD A

V35A-FTS ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
A485278N02
4.552,4.698 5.281,4.906 0.729,0.208 1.438,4.281 2.167,4.49 0.729,0.208 5.281,4.792 5.781,4.792 false 2.646,1.198 3,1.198 false 1.323,3.094 1.323,4.385 1.323,4.385 1.427,4.385 false 5.979,2.948 5.979,2.094 5.979,2.094 6.156,2.094 false 4.688,2.073 4.688,1.365 4.688,1.365 4.865,1.365 false 1.156,1.531 1.156,0.573 1.156,0.573 1.292,0.573 false 2.906,3.302 3.406,3.302 false 0.573,2.333 1.073,2.333 false 4.313,4.667 4.865,5.021 0.552,0.354 18 false 1 2.521,4.26 3.073,4.615 0.552,0.354 18 false 1 1.781,0.458 2.333,0.813 0.552,0.354 18 false 2 3.531,1.031 4.083,1.385 0.552,0.354 18 false 2 5.354,1.26 5.906,1.615 0.552,0.354 18 false 2 6.604,1.969 7.031,2.333 0.427,0.365 18 false 2 1.25,1.448 1.708,1.646 0.458,0.198 10 false x 2 6.073,2.896 6.531,3.094 0.458,0.198 10 false x 2 4.771,2.021 5.229,2.219 0.458,0.198 10 false x 3 2.677,1.219 3.135,1.417 0.458,0.198 10 false x 3 1.396,3.083 1.854,3.281 0.458,0.198 10 false x 3 5.948,4.76 6.406,4.958 0.458,0.198 10 false x 3 1.635,0.479 1.792,0.677 0.156,0.198 10 false ● 3.375,1.063 3.531,1.26 0.156,0.198 10 false ● 5.208,1.281 5.365,1.479 0.156,0.198 10 false ● 6.469,1.99 6.625,2.188 0.156,0.198 10 false ● 4.615,4.729 5.427,4.885 0.813,0.156 8 false 20 (204, 15) 0.385,2.24 0.844,2.438 0.458,0.198 10 false *1 2.729,3.208 3.083,3.438 0.354,0.229 10 false *2 1.5,4.313 2.313,4.469 0.813,0.156 8 false 20 (204, 15)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 STUD BOLT - (Click here) - -
2 RING PIN - (Click here) - -

*1 CYLINDER HEAD SUB-ASSEMBLY RH *2 CYLINDER HEAD SUB-ASSEMBLY LH
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

A489371N01
4.51,0.719 5.24,0.906 0.729,0.188 0.896,0.354 1.625,0.542 0.729,0.188 3.625,5.24 4.531,5.427 0.906,0.188 5.24,3.438 6.146,3.625 0.906,0.188 4.792,2.458 4.792,1.188 4.792,1.188 4.958,1.188 false 1.125,4.76 1.125,4.083 1.125,4.083 0.969,4.083 false 2.646,1.365 2.76,1.365 false 3,0.385 3.333,0.385 false 2.531,0.615 2.865,0.615 false 2.948,1.01 3.281,1.01 false 2.844,1.667 3.177,1.667 false 2.74,2 3.021,2 false 6.396,1.5 6.729,1.5 false 6.167,1.646 6.5,1.646 false 5.865,1.854 6.198,1.854 false 5.375,2.688 5.188,2.688 5.188,2.688 5.188,2.281 false 5.229,3.531 5.063,3.531 5.063,3.531 5.063,3.115 false 4.333,2.083 4.333,0.813 4.333,0.813 4.5,0.813 false 4.115,2.219 4.115,2.51 false 4.635,3.229 4.635,3.521 false 3.063,4.99 3.396,4.99 false 3.292,5.323 3.625,5.323 false 1.802,5.323 2.115,5.323 false 1.615,1.083 1.896,0.458 1.896,0.458 1.635,0.458 false 4.917,4.125 5.25,4.125 false 5.75,2.406 5.479,2.406 5.479,2.406 5.479,2.094 false 3.375,0.271 3.688,0.469 0.313,0.198 10 false *1 6.771,1.385 7.083,1.583 0.313,0.198 10 false *1 2.354,0.51 2.667,0.708 0.313,0.198 10 false *2 6.531,1.563 6.844,1.76 0.313,0.198 10 false *2 3.323,0.906 3.635,1.104 0.313,0.198 10 false *3 6.24,1.76 6.552,1.958 0.313,0.198 10 false *4 3.458,4.896 3.854,5.125 0.396,0.229 10 false ● 4.604,3.542 5,3.771 0.396,0.229 10 false ● 4.083,2.51 4.479,2.74 0.396,0.229 10 false ● 1.458,5.188 1.927,5.542 0.469,0.354 18 false 12 0.635,3.958 1.177,4.313 0.542,0.354 18 false 13 2.354,1.219 2.885,1.615 0.531,0.396 18 false 10 6.229,2.281 6.646,2.635 0.417,0.354 18 false 11 3.25,1.5 3.531,1.854 0.281,0.354 18 false 9 5.469,2.531 5.75,2.885 0.281,0.354 18 false 9 0.677,0.302 0.958,0.656 0.281,0.354 18 false 8 4.896,5.177 5.177,5.531 0.281,0.354 18 false 7 6.5,3.385 6.781,3.74 0.281,0.354 18 false 7 5.333,0.688 5.615,1.042 0.281,0.354 18 false 6 3.51,1.865 3.979,2.271 0.469,0.406 18 false 4 5.448,1.031 5.917,1.438 0.469,0.406 18 false 3 5.302,1.063 5.542,1.292 0.24,0.229 10 false ● 3.344,1.906 3.583,2.135 0.24,0.229 10 false ● 5.927,3.99 6.208,4.344 0.281,0.354 18 false 5 5.583,4.031 5.979,4.26 0.396,0.229 10 false ● ★ 4.573,0.74 5.354,0.917 0.781,0.177 8 false 20 (204, 15) 0.948,0.375 1.729,0.552 0.781,0.177 8 false 25 (255, 18) 3.677,5.26 4.656,5.469 0.979,0.208 8 false 135 (1377, 100) 5.281,3.458 6.26,3.667 0.979,0.208 8 false 135 (1377, 100) 1.698,1.052 2.156,1.25 0.458,0.198 10 false x 2 4.927,4.146 5.385,4.344 0.458,0.198 10 false x 3 6.104,2.323 6.344,2.552 0.24,0.229 10 false ● 2.25,1.25 2.49,1.479 0.24,0.229 10 false ● 2.25,5.479 2.573,5.656 0.323,0.177 10 false x 6 0.958,4.938 1.281,5.115 0.323,0.177 10 false x 6 4.719,2.542 5.042,2.719 0.323,0.177 10 false x 6 5.24,2.271 5.563,2.448 0.323,0.177 10 false x 6 5.542,2.052 5.865,2.229 0.323,0.177 10 false x 6 5.854,1.906 6.177,2.083 0.323,0.177 10 false x 6 6,1.417 6.323,1.594 0.323,0.177 10 false x 6 6.25,1.281 6.573,1.458 0.323,0.177 10 false x 6 2.865,0.167 3.188,0.344 0.323,0.177 10 false x 6 3.021,0.542 3.344,0.719 0.323,0.177 10 false x 6 2.969,1.031 3.292,1.208 0.323,0.177 10 false x 6 2.927,1.302 3.25,1.479 0.323,0.177 10 false x 6 2.813,1.688 3.135,1.865 0.323,0.177 10 false x 6 2.771,2.031 3.094,2.208 0.323,0.177 10 false x 6

Procedure Part Name Code
Z101186

Z101188

Z101187

3 EXHAUST VALVE GUIDE BUSH LH 11126D (Click here) - -
4 INTAKE VALVE GUIDE BUSH LH 11122D (Click here) - -
5 SPARK PLUG TUBE - (Click here) - -
6 NO. 1 STRAIGHT SCREW PLUG WITH HEAD 11117E -
7 NO. 2 STRAIGHT SCREW PLUG LH WITH HEAD 11117L (Click here) - -
8 NO. 1 STRAIGHT SCREW PLUG LH WITH HEAD 11117K (Click here) - -
9 CYLINDER HEAD VALVE SPRING SEAT LH 13734D - - -
10 CYLINDER HEAD INTAKE VALVE STEM OIL SEAL LH 13711L (Click here) - -
11 CYLINDER HEAD EXHAUST VALVE STEM OIL SEAL LH 13715G (Click here) - -
12 CYLINDER HEAD INTAKE VALVE LH 13711G (Click here) - -
13 CYLINDER HEAD EXHAUST VALVE LH 13715C (Click here) - -

*1 CYLINDER HEAD VALVE SPRING RETAINER LOCK LH *2 CYLINDER HEAD VALVE SPRING RETAINER LH
*3 CYLINDER HEAD INTAKE COMPRESSION SPRING LH *4 CYLINDER HEAD EXHAUST COMPRESSION SPRING LH
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent ★ Precoated part

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the Bank 1 side and Bank 2 side.

·

The following procedure is for the Bank 2 side.



PROCEDURE

Hide 1.INSTALL STUD BOLT

a.
A485286C01
1.656,0.292 1.969,0.448 0.313,0.156 10 false *a 1.667,1.479 1.979,1.635 0.313,0.156 10 false *b 5.177,1.094 5.49,1.25 0.313,0.156 10 false *c 5.177,1.813 5.49,1.969 0.313,0.156 10 false *d 5.688,1.375 6,1.531 0.313,0.156 10 false *e 0.438,0.052 0.771,0.354 0.333,0.302 18 false i
*a for Bank 1 *b for Bank 2
*c 22.5 mm (0.886 in.) *d 20 mm (0.787 in.)
*e 46 mm (1.81 in.) - -


i.

Using E10 "TORX" socket wrench, install the stud bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)



Hide 2.INSTALL RING PIN

a.
A491976C01
0.781,0.271 1.094,0.427 0.313,0.156 10 false *a 0.781,2.281 1.094,2.438 0.313,0.156 10 false *b 4.365,2.51 4.677,2.667 0.313,0.156 10 false *c 6.552,1.875 6.865,2.031 0.313,0.156 10 false *e 4.385,1.146 4.542,1.302 0.156,0.156 10 false A 5.802,2.49 6.115,2.646 0.313,0.156 10 false *d 5.844,1.167 6,1.323 0.156,0.156 10 false B 0.448,0.052 0.698,0.375 0.25,0.323 18 false i 5.083,1.771 5.396,1.927 0.313,0.156 10 false *c
*a for Bank 1 *b for Bank 2
*c 12 mm (0.472 in) *d 11 mm (0.433 in.)
*e 8 mm (0.315 in.) - -
V100135

Ring Pin A
V100136

Ring Pin B


i.

Using a plastic-faced hammer, tap in new ring pins to the specified protrusion height.

Standard protrusion height:
Ring pin A:

5.5 to 6.5 mm (0.217 to 0.256 in.)

Ring pin B:

4.5 to 5.5 mm (0.177 to 0.217 in.)




Hide 11126D 3.INSTALL EXHAUST VALVE GUIDE BUSH LH

a.
A491643C01
2.25,3.75 2.729,4.344 2.729,4.344 2.5,3.542 true 0.781,3.698 1,3.875 0.219,0.177 10 true *a 2.708,4.375 3.094,4.583 0.385,0.208 10 false SST 0.469,0.052 0.719,0.323 0.25,0.271 18 false i 4.219,0.052 4.719,0.333 0.5,0.281 18 false ii 0.49,2.427 1.031,2.708 0.542,0.281 18 false iii, iv 4.198,2.427 4.448,2.698 0.25,0.271 18 false v
*a Protrusion Height - -


i.

Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head sub-assembly.

Standard cylinder bore diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


Select a New Guide Bush (STD or O/S 0.05)
Bush Size Specified Condition
STD 10.333 to 10.344 mm (0.40681 to 0.40724 in.)
O/S 0.05 10.383 to 10.394 mm (0.40878 to 0.40921 in.)

HINT:
·

If the bush bore diameter of the cylinder head sub-assembly is more than 10.306 mm (0.406 in.), machine the bush bore to the dimension of 10.335 to 10.356 mm (0.407 to 0.408 in.) to install an O/S 0.05 valve guide bush.

·

If the bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.




ii.

Heat the cylinder head to 80 to 100°C (176 to 212°F).

CAUTION:
·

Do not touch the cylinder head sub-assembly without wearing protective gloves, as it may get very hot during operation.

·

Be sure to wear protective gloves to avoid burns.




iii.

Place the cylinder head sub-assembly on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



iv.

Using SST, tap in new exhaust valve guide bushes to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard protrusion height:

19.75 to 20.0 mm (0.778 to 0.787 in.)



v.

Using a sharp 5.5 mm reamer, ream the valve guide bushings to obtain the specified clearance.

Standard oil clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)




Hide 11122D 4.INSTALL INTAKE VALVE GUIDE BUSH LH

a.
A491644C01
1.875,3.813 1.375,4.365 1.375,4.365 1.948,3.917 true 2.979,3.26 3.198,3.438 0.219,0.177 10 true *a 1.188,4.396 1.573,4.604 0.385,0.208 10 false SST 0.469,0.052 0.719,0.323 0.25,0.271 18 false i 4.219,0.052 4.719,0.333 0.5,0.281 18 false ii 0.49,2.427 1.031,2.708 0.542,0.281 18 false iii, iv 4.198,2.427 4.448,2.698 0.25,0.271 18 false v
*a Protrusion Height - -


i.

Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head sub-assembly.

Standard cylinder bore diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


Select a New Guide Bush (STD or O/S 0.05)
Bush Size Specified Condition
STD 10.333 to 10.344 mm (0.40681 to 0.40724 in.)
O/S 0.05 10.383 to 10.394 mm (0.40878 to 0.40921 in.)

HINT:
·

If the bush bore diameter of the cylinder head sub-assembly is more than 10.306 mm (0.406 in.), machine the bush bore to the dimension of 10.335 to 10.356 mm (0.407 to 0.408 in.) to install an O/S 0.05 valve guide bush.

·

If the bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.




ii.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).

CAUTION:
·

Do not touch the cylinder head sub-assembly without wearing protective gloves, as it may get very hot during operation.

·

Be sure to wear protective gloves to avoid burns.




iii.

Place the cylinder head sub-assembly on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



iv.

Using SST, tap in new intake valve guide bushes to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard protrusion height:

19.35 to 19.6 mm (0.762 to 0.772 in.)



v.

Using a sharp 5.5 mm reamer, ream the valve guide bushings to obtain the specified clearance.

Standard oil clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)




Hide 5.INSTALL SPARK PLUG TUBE

Z101186

NOTICE:

When using a new cylinder head sub-assembly, the spark plug tubes must be replaced.



a.
A485290C01
2.229,2.927 2.229,1.969 true 5.198,2.719 5.083,2.229 false 2.156,2.938 2.469,3.094 0.313,0.156 10 false *a 1.958,1.344 2.271,1.5 0.313,0.156 10 false *b 1.76,2.594 2.073,2.75 0.313,0.156 10 false *c 6.333,2.323 6.646,2.479 0.313,0.156 10 false *d 4.969,2.063 5.281,2.219 0.313,0.156 10 false *e 0.865,0.802 1.156,1.073 0.292,0.271 18 false i 4.26,0.094 4.552,0.365 0.292,0.271 18 false ii
*a Adhesive *b 1.0 to 7.0 mm (0.0394 to 0.276 in.)
*c 0 to 1.0 mm (0 to 0.0394 in.) *d Standard Protrusion Height
*e Cylinder Head Casting Surface - -


i.

Apply adhesive onto the shaded area of a new spark plug tube.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.


NOTICE:
·

Install the spark plug tube within 3 minutes after applying adhesive.

·

Be careful not to expose the seal to coolant for at least 1 hour after installing it.

·

Be careful not to deform the spark plug tube.




ii.

Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.

Standard protrusion height:

75.3 to 76.3 mm (2.96 to 3.00 in.)


NOTICE:

To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.




Hide 11117E 6.INSTALL NO. 1 STRAIGHT SCREW PLUG WITH HEAD

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

Hide 11117L 7.INSTALL NO. 2 STRAIGHT SCREW PLUG LH WITH HEAD

a.
A490197N01
2.604,0.51 2.885,0.865 0.281,0.354 18 false i 0.542,2.177 0.823,2.531 0.281,0.354 18 false ii

i.

Install new gaskets to the No. 2 straight screw plugs LH with head.


ii.

Using a 14 mm hexagon wrench, install the No. 2 straight screw plugs LH with head.

Torque:
135 N*m (1377 kgf*cm, 100 ft.*lbf)



Hide 11117K 8.INSTALL NO. 1 STRAIGHT SCREW PLUG LH WITH HEAD

a.
A490198N01
0.604,0.104 0.885,0.458 0.281,0.354 18 false i 4.021,0.104 4.302,0.458 0.281,0.354 18 false ii

i.

Apply adhesive to the No. 1 straight screw plugs LH with head of the cylinder head sub-assembly.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



ii.

Using a 6 mm hexagon wrench, install the No. 1 straight screw plugs LH with head.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

Do not expose the No. 1 straight screw plug LH with head to engine oil for at least 1 hour after installing it.




Hide 13734D 9.INSTALL CYLINDER HEAD VALVE SPRING SEAT LH

Hide 13711L 10.INSTALL CYLINDER HEAD INTAKE VALVE STEM OIL SEAL LH

a.
A485291C01
4.354,1.823 5.573,0.885 true 0.99,2.063 1.083,1.75 true 2.583,2.063 2.677,1.75 true 1.021,0.604 1.333,0.76 0.313,0.156 10 false *a 2.604,0.646 2.917,0.802 0.313,0.156 10 false *b 0.875,2.073 1.188,2.229 0.313,0.156 10 false *c 2.469,2.083 2.781,2.24 0.313,0.156 10 false *d 5.094,1.885 5.406,2.042 0.313,0.156 10 false *e 6.094,1.896 6.406,2.052 0.313,0.156 10 false *f 4.146,1.844 4.604,2.042 0.458,0.198 10 false SST 0.448,0.042 0.75,0.354 0.302,0.313 18 false i 3.896,0.042 4.198,0.354 0.302,0.313 18 false ii
*a Intake Side *b Exhaust Side
*c Gold *d Gray
*e CORRECT *f INCORRECT


i.

Apply a light coat of engine oil to new cylinder head intake valve stem oil seals.

NOTICE:

Pay attention when installing the intake and exhaust valve stem oil seals. For example, installing the intake valve stem oil seal to the exhaust side or installing the exhaust valve stem oil seal to the intake side can cause installation problems later.


HINT:

The intake valve oil seals are gold and the exhaust valve oil seals are gray.



ii.

Using SST, push in the cylinder head intake valve stem oil seals.

SST
09201-41020  

NOTICE:

Failure to use SST will cause the seal to be damaged or improperly seated.




Hide 13715G 11.INSTALL CYLINDER HEAD EXHAUST VALVE STEM OIL SEAL LH

a.

Use the same procedure for the cylinder head exhaust valve stem oil seal LH and cylinder head intake valve stem oil seal LH.


Hide 13711G 12.INSTALL CYLINDER HEAD INTAKE VALVE LH

a.
A485292C01
4.875,0.417 5.354,0.417 false 4.823,1.271 5.302,1.271 false 5.979,1.698 6.229,1.281 false 1.552,2.469 1.979,2.156 true 4.677,0.313 4.99,0.469 0.313,0.156 10 false *1 4.646,1.177 4.958,1.333 0.313,0.156 10 false *2 6.198,1.104 6.51,1.26 0.313,0.156 10 false *3 2.458,1.26 2.771,1.417 0.313,0.156 10 false *a 0.51,0.094 0.833,0.406 0.323,0.313 18 false i 4.188,0.094 4.51,0.406 0.323,0.313 18 false ii 0.531,2.052 0.854,2.365 0.323,0.313 18 false iii 4.156,2.042 4.479,2.354 0.323,0.313 18 false iv 2.031,2.052 2.49,2.271 0.458,0.219 10 false SST
*1 Cylinder Head Valve Spring Retainer LH *2 Cylinder Head Intake Compression Spring LH
*3 Cylinder Head Sub-assembly - -
*a 30 mm (1.18 in.) or more - -
V100135

Top - -


i.

Apply a sufficient coat of engine oil to the tip area of the cylinder head intake valve LH shown in the illustration.


ii.

Install the cylinder head intake valve LH, cylinder head intake compression spring LH and cylinder head valve spring retainer LH to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



iii.

Using SST, compress each compression spring and install the 6 cylinder head valve spring retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  


iv.

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the retainer.




Hide 13715C 13.INSTALL CYLINDER HEAD EXHAUST VALVE LH

a.
A485293C01
4.875,0.417 5.354,0.417 false 4.823,1.271 5.302,1.271 false 5.979,1.698 6.229,1.281 false 2.885,2.354 3.24,2.198 true 4.677,0.313 4.99,0.469 0.313,0.156 10 false *1 4.646,1.177 4.958,1.333 0.313,0.156 10 false *2 6.198,1.104 6.51,1.26 0.313,0.156 10 false *3 2.458,1.26 2.771,1.417 0.313,0.156 10 false *a 0.479,0.094 0.802,0.406 0.323,0.313 18 false i 4.188,0.083 4.51,0.396 0.323,0.313 18 false ii 0.49,2.052 0.813,2.365 0.323,0.313 18 false iii 4.167,2.042 4.49,2.354 0.323,0.313 18 false iv 3.292,2.104 3.75,2.323 0.458,0.219 10 false SST
*1 Cylinder Head Valve Spring Retainer LH *2 Cylinder Head Exhaust Compression Spring LH
*3 Cylinder Head Sub-assembly - -
*a 30 mm (1.18 in.) or more - -
V100135

Top - -


i.

Apply a sufficient coat of engine oil to the tip area of the cylinder head exhaust valve LH shown in the illustration.


ii.

Install the cylinder head exhaust valve LH, cylinder head exhaust compression spring LH and cylinder head valve spring retainer LH to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



iii.

Using SST, compress each compression spring and install the 6 cylinder head valve spring retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  


iv.

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the retainer.