Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM38G0E _59 Vehicle Exterior _100456 WIPER / WASHER _0467584 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Front Wiper Motor Circuit  


DESCRIPTION

The windshield wiper relay assembly controls the windshield wiper motor assembly through this circuit.

WIRING DIAGRAM

for LHD:


E404635E06
0.792,2.677 1.917,3.104 1.125,0.427 10 false Windshield Wiper Relay Assembly 1.99,0.75 2.448,0.948 0.458,0.198 10 false I95 1.99,1.385 2.448,1.583 0.458,0.198 10 false I94 1.99,2.021 2.448,2.219 0.458,0.198 10 false I95 1.646,0.75 1.958,0.948 0.313,0.198 10 false +2 1.5,1.396 1.885,1.583 0.385,0.188 10 false +SM 1.635,2.031 1.948,2.229 0.313,0.198 10 false +1 2.031,0.542 2.188,0.74 0.156,0.198 10 false 4 2.042,1.177 2.354,1.375 0.313,0.198 10 false 6 2.042,1.813 2.198,2.01 0.156,0.198 10 false 2 3.854,0.635 4.01,0.833 0.156,0.198 10 false 4 3.854,1.281 4.01,1.479 0.156,0.198 10 false 3 3.844,1.885 4,2.083 0.156,0.198 10 false 1 4.063,0.625 4.375,0.823 0.313,0.198 10 false +2 4.052,1.271 4.438,1.458 0.385,0.188 10 false +S 4.052,1.885 4.365,2.083 0.313,0.198 10 false +1 6.156,1.281 6.313,1.479 0.156,0.198 10 false E 6.385,1.281 6.542,1.479 0.156,0.198 10 false 5 4.125,2.719 4.583,2.917 0.458,0.198 10 false B28 4.125,2.896 6.281,3.125 2.156,0.229 10 false Windshield Wiper Motor Assembly


for RHD:


E404635E07
0.792,2.677 1.917,3.104 1.125,0.427 10 false Windshield Wiper Relay Assembly 1.99,0.75 2.448,0.948 0.458,0.198 10 false I95 1.99,1.385 2.448,1.583 0.458,0.198 10 false I94 1.99,2.021 2.448,2.219 0.458,0.198 10 false I95 1.646,0.75 1.958,0.948 0.313,0.198 10 false +2 1.5,1.396 1.885,1.583 0.385,0.188 10 false +SM 1.635,2.031 1.948,2.229 0.313,0.198 10 false +1 2.031,0.542 2.188,0.74 0.156,0.198 10 false 4 2.042,1.177 2.354,1.375 0.313,0.198 10 false 6 2.042,1.813 2.198,2.01 0.156,0.198 10 false 2 3.854,0.635 4.01,0.833 0.156,0.198 10 false 3 3.854,1.281 4.01,1.479 0.156,0.198 10 false 1 3.854,1.885 4.01,2.083 0.156,0.198 10 false 5 4.063,0.625 4.375,0.823 0.313,0.198 10 false +2 4.052,1.271 4.438,1.458 0.385,0.188 10 false +S 4.052,1.885 4.365,2.083 0.313,0.198 10 false +1 6.156,1.281 6.313,1.479 0.156,0.198 10 false E 6.385,1.281 6.542,1.479 0.156,0.198 10 false 4 4.125,2.719 4.583,2.917 0.458,0.198 10 false B28 4.125,2.896 6.281,3.125 2.156,0.229 10 false Windshield Wiper Motor Assembly


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (FRONT WIPER OPERATION)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Wiper Lo Operation Function to operate the windshield wiper motor assembly in LO OFF or ON -
Front Wiper Hi Operation Function to operate the windshield wiper motor assembly in HI OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Front Wiper Lo Operation
50004 449 72
Body Electrical > Main Body > Active Test
Tester Display
Front Wiper Hi Operation
50004 449 73
OK:

Windshield wiper motor assembly operates normally.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY
2.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WINDSHIELD WIPER MOTOR ASSEMBLY)

NG

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WINDSHIELD WIPER MOTOR ASSEMBLY)
a.

Disconnect the I95 and I94 windshield wiper relay assembly connectors.


b.

Disconnect the B28 windshield wiper motor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(I95,B28,I94)Location & Routing

Click Connector(I95)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Windshield Wiper Relay Assembly

Click Connector(B28)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Windshield Wiper Motor Assembly

Click Connector(I94)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Windshield Wiper Relay Assembly

I95-2 (+1) - B28-1 (+1) Always Below 1 Ω
I95-4 (+2) - B28-4 (+2) Always Below 1 Ω
I94-6 (+SM) - B28-3 (+S) Always Below 1 Ω
I95-2 (+1) or B28-1 (+1) - Body ground Always 10 kΩ or higher
I95-4 (+2) or B28-4 (+2) - Body ground Always 10 kΩ or higher
I94-6 (+SM) or B28-3 (+S) - Body ground Always 10 kΩ or higher


for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(I95,B28,I94)Location & Routing

Click Connector(I95)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Windshield Wiper Relay Assembly

Click Connector(B28)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Windshield Wiper Motor Assembly

Click Connector(I94)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Windshield Wiper Relay Assembly

I95-2 (+1) - B28-5 (+1) Always Below 1 Ω
I95-4 (+2) - B28-3 (+2) Always Below 1 Ω
I94-6 (+SM) - B28-1 (+S) Always Below 1 Ω
I95-2 (+1) or B28-5 (+1) - Body ground Always 10 kΩ or higher
I95-4 (+2) or B28-3 (+2) - Body ground Always 10 kΩ or higher
I94-6 (+SM) or B28-1 (+S) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BODY GROUND)
a.

Disconnect the B28 windshield wiper motor assembly connector.


b.

Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR