Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM38G0E _59 Vehicle Exterior _100456 WIPER / WASHER _0467584 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Washer Motor Circuit  


DESCRIPTION

When the windshield washer motor and pump assembly receives signals from the windshield wiper switch assembly, it operates to spray washer fluid from the washer nozzle.

WIRING DIAGRAM

E463723E04
0.521,4.083 2.781,4.313 2.26,0.229 10 false Windshield Wiper Relay Assembly 0.531,3.917 0.844,4.115 0.313,0.198 10 false I95 1.667,0.75 2.115,0.938 0.448,0.188 10 false IGWS 1.729,1.781 2.188,1.979 0.458,0.198 10 false +WR 1.76,2.354 2.219,2.552 0.458,0.198 10 false -WR 1.729,3.385 2.188,3.583 0.458,0.198 10 false EWS 2.208,0.646 2.365,0.844 0.156,0.198 10 false 6 2.188,1.688 2.344,1.885 0.156,0.198 10 false 1 2.188,2.26 2.344,2.458 0.156,0.198 10 false 7 2.198,3.281 2.354,3.479 0.156,0.198 10 false 5 3.323,0.958 4.24,1.156 0.917,0.198 10 false WASHER 4.667,0.781 6.146,0.979 1.479,0.198 10 false from IGR NO.4 Relay 4.781,1.594 4.938,1.792 0.156,0.198 10 false 1 4.792,2.177 4.948,2.375 0.156,0.198 10 false 2 5.083,2.25 5.396,2.448 0.313,0.198 10 false SW 5.115,1.688 5.427,1.885 0.313,0.198 10 false B 3.073,2.375 3.417,2.573 0.344,0.198 10 false BB1 5.042,2.927 6.667,3.375 1.625,0.448 10 false Windshield Washer Motor and Pump Assembly 3.073,1.802 3.396,2 0.323,0.198 10 false BB1 3.167,1.583 3.323,1.781 0.156,0.198 10 false 4 3.156,2.167 3.313,2.365 0.156,0.198 10 false 5 4.719,1.802 5.042,2.01 0.323,0.208 10 false B50 4.719,2.385 5.052,2.594 0.333,0.208 10 false B50 3.604,2.917 4.531,3.24 0.927,0.323 10 false Washer Wiring Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuse of circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (WASHER RELAY)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Washer Relay Operates the windshield wiper relay assembly OFF or ON -
Rear Washer Relay Operates the windshield wiper relay assembly OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Front Washer Relay
50004 449 71
Body Electrical > Main Body > Active Test
Tester Display
Rear Washer Relay
50004 449 76
OK:

Windshield washer motor and pump assembly operate normally.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY
2.INSPECT WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY

Click hereVehicle Exterior>WIPER / WASHER>WASHER MOTOR>INSPECTION

Result:
Proceed to
OK
NG



OK

3.INSPECT WASHER WIRING ASSEMBLY

NG

REPLACE WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY

3.INSPECT WASHER WIRING ASSEMBLY
a.

Remove the washer wiring assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(BB1,B50)Location & Routing

Click Connector(BB1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and Washer Wiring Assembly

Click Connector(B50)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Windshield Washer Motor and Pump Assembly

BB1-4 - B50-1 (B) Always Below 1 Ω
BB1-5 - B50-2 (SW) Always Below 1 Ω
BB1-4 or B50-1 (B) - Body ground Always 10 kΩ or higher
BB1-5 or B50-2 (SW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPLACE WASHER WIRING ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the I95 windshield wiper relay assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I95)Location & Routing

Click Connector(I95)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Windshield Wiper Relay Assembly

I95-6 (IGWS) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I95)Location & Routing

Click Connector(I95)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Windshield Wiper Relay Assembly

I95-5 (EWS) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WASHER WIRING ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WASHER WIRING ASSEMBLY)
a.

Disconnect the I95 windshield wiper relay assembly connector.


b.

Disconnect the BB1 washer wiring assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I95,BB1)Location & Routing

Click Connector(I95)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Windshield Wiper Relay Assembly

Click Connector(BB1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and Washer Wiring Assembly

I95-1 (+WR) - BB1-4 Always Below 1 Ω
I95-7 (-WR) - BB1-5 Always Below 1 Ω
I95-1 (+WR) or BB1-4 - Body ground Always 10 kΩ or higher
I95-7 (-WR) or BB1-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR