Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SENSOR
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0467784 BLIND SPOT MONITOR SENSOR A

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B594924N01
5.365,2.177 5.615,2.427 5.615,2.427 5.948,2.427 false 1.229,0.781 1.646,0.781 1.646,0.781 1.813,1.031 false 3.583,0.75 4,0.75 4,0.75 4.167,0.531 false 6.469,0.219 6.802,0.219 false 6.01,2.25 6.292,2.604 0.281,0.354 18 false 2 1.052,0.615 1.333,0.969 0.281,0.354 18 false 3 3.396,0.573 3.677,0.927 0.281,0.354 18 false 4 1.375,1.667 1.833,1.865 0.458,0.198 10 false x 3 4.875,0.49 5.333,0.688 0.458,0.198 10 false x 3 6.313,0.052 6.594,0.406 0.281,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BSM ECU DATE SAVE - - - (Click here)
2 REAR BUMPER ASSEMBLY - - - -
3 BLIND SPOT MONITOR SENSOR LH 88172 - - -
4 BLIND SPOT MONITOR SENSOR RH 88162 - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the blind spot monitor sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
w/ Hands Free Power Back Door:

Disconnect cable from negative (-) battery terminal


Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)
Blind spot monitor sensor Blind spot monitor beam axis confirmation
·

DTCs are output

·

Parking support alert system

·

Parking support brake system

·

Blind spot monitor system


(Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -




PROCEDURE

Hide 88172 3.REMOVE BLIND SPOT MONITOR SENSOR LH

a.
B594956


Hide 88162 4.REMOVE BLIND SPOT MONITOR SENSOR RH

a.

Use the same procedure described for the LH side.