Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU (for RHD)
RM38G0E _57 Power Source / Network _100627 POWER DISTRIBUTION _0467798 MAIN BODY ECU(for RHD) A

POWER DISTRIBUTION  MAIN BODY ECU(for RHD)  INSTALLATION  


CAUTION / NOTICE / HINT

E474022N01
1.354,1.771 5.76,3.719 4.406,1.948 6.583,0.188 6.854,0.188 false 4.625,2.458 4.969,2.458 false 2.438,3.5 2.708,3.5 false 0.917,0.417 1.188,0.417 false 3.75,0.417 4,0.417 4,0.417 4.333,0.667 false 2.51,2.688 2.677,2.688 2.677,2.688 2.75,2.979 false 3.333,1.938 3.604,1.938 false 6.615,0.76 6.781,0.76 false 6.417,0.01 6.698,0.365 0.281,0.354 18 false 1 5.25,2.323 5.5,2.625 0.25,0.302 18 false 2 2.354,2.51 2.635,2.865 0.281,0.354 18 false 3 3.146,1.792 3.427,2.146 0.281,0.354 18 false 4 2.771,3.323 3.052,3.677 0.281,0.354 18 false 5 0.729,0.292 1.01,0.646 0.281,0.354 18 false 6 3.615,0.25 3.896,0.604 0.281,0.354 18 false 7 2.167,0.792 2.625,0.99 0.458,0.198 10 false x 2 5.135,2.354 5.292,2.552 0.156,0.198 10 false ● 6.438,0.635 6.719,0.99 0.281,0.354 18 false 8

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 89221 (Click here) - -
3 JUNCTION BLOCK BRACKET 82673B - - -
4 JUNCTION BLOCK BRACKET 82673A - - -
5 WIRING HARNESS CLAMP BRACKET 82715 - - -
6 POWER DISTRIBUTION BOX ASSEMBLY 82730G - - -
7 LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY 73900 - - -
8 ECU CONFIGURATION - - - (Click here)

● Non-reusable part - -

CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS


NOTICE:
·

After replacing the MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU), make sure to perform ECU configuration.

·

After performing the ECU configuration procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:
·

When installing the main body ECU (multiplex network body ECU), always replace it with a new one.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.




Hide 89221 2.INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

Z101186

NOTICE:
·

Do not touch the connector.

·

Make sure foreign matter does not enter the terminals.




a.
E464747C01
2.802,2.875 2.802,3.417 true 0.656,0.844 1.219,0.844 true 4.229,0.854 4.792,0.854 true 5.271,2.615 5.677,2.25 5.677,2.25 5.896,2.25 true 5.552,0.708 5.958,0.344 5.958,0.344 6.177,0.344 true 0.917,0.052 1.198,0.406 0.281,0.354 18 false i 4.698,0.052 4.979,0.406 0.281,0.354 18 false ii 1.875,1.938 2.156,2.292 0.281,0.354 18 false iii 0.479,0.75 0.792,0.948 0.313,0.198 10 false *a 1.094,1.292 1.406,1.49 0.313,0.198 10 false *b 4.021,0.76 4.333,0.958 0.313,0.198 10 false *a 6.219,0.219 6.531,0.417 0.313,0.198 10 false *c 5.927,2.156 6.24,2.354 0.313,0.198 10 false *c 2.729,3.438 3.042,3.635 0.313,0.198 10 false *c
*a Housing Sidewall *b 20° or more
*c Power Distribution Box Assembly Side A - -
V113147

Set in this Direction
V113148

Slide in this Direction
V113149

Install in this Direction - -


i.

Press the main body ECU (multiplex network body ECU) to the housing sidewall as shown in the illustration.

HINT:

Make sure the angle between the power distribution box assembly and the main body ECU (multiplex network body ECU) is 20° or more.



ii.

Slide the main body ECU (multiplex network body ECU) along the housing sidewall in the direction of the arrow (power distribution box assembly side A) and insert the guide as shown in the illustration.

NOTICE:

Do not press against the main body ECU (multiplex network body ECU) sidewall too hard.



iii.

Rotate the main body ECU (multiplex network body ECU) about its edge which contacts with the power distribution box assembly side A as shown in the illustration.



b.
E464748C01
4.552,1.354 4.552,0.979 4.552,0.979 4.729,0.979 true 2.792,2.146 2.792,2.479 true 4.854,0.969 5.094,0.969 5.094,0.969 5.094,1.167 true 4.625,2.552 4.625,2.104 4.625,2.104 5.146,2.104 true 2.365,2.49 2.365,2.156 2.365,2.156 3.198,2.156 true 0.563,0.083 0.844,0.438 0.281,0.354 18 false i 4.552,0.083 4.833,0.438 0.281,0.354 18 false ii 1.74,1.99 2.021,2.344 0.281,0.354 18 false iii 1.031,0.615 1.344,0.813 0.313,0.198 10 false *a 4.521,1.375 4.833,1.573 0.313,0.198 10 false *2 5.021,1.208 5.333,1.406 0.313,0.198 10 false *1 5.188,2.021 5.5,2.219 0.313,0.198 10 false *c 3.24,2.073 3.552,2.271 0.313,0.198 10 false *b
*1 Power Distribution Box Assembly *2 Main Body ECU (Multiplex Network Body ECU)
*a Before Locking *b Press the 2 sides of the main body ECU (multiplex network body ECU) with both hands.
*c Press the center of the main body ECU (multiplex network body ECU) with one hand. - -
V113146

Place fingers or the palm of your hand here
V113147

Install in this Direction
V100155

Pressing Area - -


i.

Rotate it until the main body ECU (multiplex network body ECU) enters the lock of the power distribution box assembly.


ii.

Press the push area, attach the claw, and install the main body ECU (multiplex network body ECU).

NOTICE:
·

Be sure to press only the push area.

·

Do not insert with a force of 98 N (10 kgf, 22.0 lbf) or higher to prevent it from being damaged.

·

Check the engagement of the main body ECU (multiplex network body ECU) and the power distribution box assembly by the locking sound.

·

Do not put your weight on the main body ECU (multiplex network body ECU) when engaging the main body ECU (multiplex network body ECU) to prevent it from being damaged.



HINT:

If a locking sound cannot be heard, visually check the lock part engagement. Or check that the height of the main body ECU (multiplex network body ECU) and the power distribution box assembly are the same.



iii.

Press it in one of the ways as shown in the illustration.



Hide 82673B 3.INSTALL JUNCTION BLOCK BRACKET

Hide 82673A 4.INSTALL JUNCTION BLOCK BRACKET

Hide 82715 5.INSTALL WIRING HARNESS CLAMP BRACKET

Hide 82730G 6.INSTALL POWER DISTRIBUTION BOX ASSEMBLY

a.
E474019C02
3.76,0.219 4.135,0.49 0.375,0.271 18 true ii 2.094,0.188 2.646,0.542 0.552,0.354 18 false iii 2.906,1.427 3.188,1.781 0.281,0.354 18 true i
V113147

Install in this Direction - -


i.

Connect the connector.


ii.

Attach the claw to connect the 2 lever connectors.

NOTICE:

Be sure to connect the lever connector securely.



iii.

Attach the clamp.



b.
E474020C02
0.26,0.229 0.531,0.583 0.271,0.354 18 true i 3.042,0.219 3.323,0.573 0.281,0.354 18 true iii 5.865,0.25 6.083,0.552 0.219,0.302 18 true ii
V113147

Install in this Direction
V100135

Connector
V100136

Nut
V100137

Bolt


i.

Install the power distribution box assembly with the 2 nuts and bolt.


ii.

Attach the claw to connect the lever connector.

NOTICE:

Be sure to connect the lever connector securely.



iii.

Attach the clamp and connect the 7 connectors.



Hide 73900 7.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY