Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0467875 SPIRAL CABLE G

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSPECTION  


PROCEDURE

Hide 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not remove the steering sensor from the spiral cable sub-assembly when inspecting the spiral cable sub-assembly.

·

Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.



a.

Visually check the spiral cable sub-assembly for defects.

i.

The defects are as follows:

·

Scratches

·

Small cracks

·

Dents

·

Chips

·

Cracks or other damage to the connector

OK:

No defects are found.



If any of the defects is found, replace the spiral cable sub-assembly with a new one.



b.

Check the spiral cable sub-assembly.

B608732C03
2.01,0.667 2.26,0.833 0.25,0.167 0.771,1.74 1.021,1.906 0.25,0.167 2.635,2.01 2.885,2.177 0.25,0.167 5.906,3.688 6.156,3.854 0.25,0.167 1.896,4.25 2.146,4.417 0.25,0.167 1.104,4.406 1.354,4.573 0.25,0.167 6.188,4.323 6.188,4.563 true 6.219,4.104 6.552,4.104 true 0.729,5.125 1.177,5.125 true 2.021,5.708 2.021,5.438 true 5.646,4.104 5.917,4.104 true 0.729,4.896 1.177,4.896 true 2.063,0.667 2.375,0.865 0.313,0.198 10 false z8 0.823,1.74 1.135,1.938 0.313,0.198 10 false z7 1.135,4.406 1.448,4.604 0.313,0.198 10 false I25 2.719,2.01 3.031,2.208 0.313,0.198 10 false A 0.542,4.802 0.854,5 0.313,0.198 10 false D+ 0.542,5.021 0.854,5.219 0.313,0.198 10 false D- 5.375,4.01 5.688,4.208 0.313,0.198 10 false BHT 6.573,4.01 6.885,4.208 0.313,0.198 10 false EHT 6.104,4.552 6.417,4.75 0.313,0.198 10 false LIN 1.927,5.698 2.24,5.896 0.313,0.198 10 false HO 5.938,3.688 6.25,3.885 0.313,0.198 10 false I53 1.927,4.25 2.24,4.448 0.313,0.198 10 false I47 0.208,0.135 0.521,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Spiral Cable Sub-assembly)
- -
V100144

Interlock - -


NOTICE:
·

When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.



i.

Set the spiral cable sub-assembly to the center position.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION


ii.

Measure the resistance between each terminal of the spiral cable sub-assembly according to the value(s) in the table below.


iii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.


iv.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*: w/ Heated Steering Wheel System

Click Location & Routing(I25,z8,I47,I53,z7)Location & Routing

Click Connector(I25)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Spiral Cable Sub-Assembly

Click Connector(z8)Instrument Panel>other>Driver Side Squib Circuit (Horn Button Assembly) , Spiral Cable Sub-Assembly

Click Connector(I47)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Spiral Cable Sub-Assembly

Click Connector(I53)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Spiral Cable Sub-Assembly

Click Connector(z7)Instrument Panel>other>Multiplex Network Steering Computer (Steering Wheel Assembly) , Spiral Cable Sub-Assembly

I25-1 (D+) - z8-2 Always Below 1 Ω
I25-2 (D-) - z8-1 Always Below 1 Ω
I47-7 (HO) - A Always 3 Ω or less
I53-1 (LIN) - z7-2 Always 3 Ω or less
I53-2 (EHT) - z7-1* Always 3 Ω or less
I53-4 (BHT) - z7-4* Always 3 Ω or less


If the result is not as specified, replace the spiral cable sub-assembly.