Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0467875 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B608726N01
0.406,2.417 2.5,3.417 2.094,1 0.406,1.25 2.5,2.25 2.094,1 3.375,3.021 3.375,2.76 true 3.677,0.844 3.677,0.51 true 5.99,2.844 5.99,2.51 true 1.573,1.75 1.906,1.75 true 1.573,2.948 1.906,2.948 true 1.438,0.615 1.771,0.615 true 6.469,0.26 6.802,0.26 true 6.406,0.625 6.74,0.625 true 4.115,2.854 4.115,2.594 true 4.625,0.083 6.24,1.156 1.615,1.073 18 false 1, 3, 7, 10, 12 0.479,2.458 0.854,2.698 0.375,0.24 12 false *B 3.615,0.24 3.896,0.594 0.281,0.354 18 false 4 1.802,0.469 2.083,0.823 0.281,0.354 18 false 5 1.948,1.604 2.229,1.958 0.281,0.354 18 false 6 1.948,2.802 2.229,3.156 0.281,0.354 18 false 6 5.927,2.813 6.208,3.167 0.281,0.354 18 false 8 4.031,2.427 4.344,2.625 0.313,0.198 10 false *1 2.177,1.406 2.49,1.604 0.313,0.198 10 false x 3 2.188,2.563 2.5,2.76 0.313,0.198 10 false x 3 6.156,0.125 6.896,0.365 0.74,0.24 12 false (*B) 3.313,2.479 3.594,2.833 0.281,0.354 18 false 2 0.479,1.302 0.854,1.542 0.375,0.24 12 false *A 5.865,0.458 6.625,1.063 0.76,0.604 18 false 9, 11

Procedure Part Name Code
Z101186

Z101188

Z101187

1 INSPECT SPIRAL CABLE SUB-ASSEMBLY - (Click here) - -
2 STEERING SENSOR 89245B (Click here) - -
3 PLACE FRONT WHEELS FACING STRAIGHT AHEAD - (Click here) - -
4 SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - (Click here) - -
5 UPPER STEERING COLUMN COVER 45286B - - -
6 LOWER STEERING COLUMN COVER SUB-ASSEMBLY 45024 - - -
7 ADJUST SPIRAL CABLE SUB-ASSEMBLY - (Click here) - -
8 STEERING WHEEL ASSEMBLY 45100 - - -
9 PERFORM DIAGNOSTIC SYSTEM CHECK - - - (Click here)
10 CHECK SRS WARNING LIGHT - (Click here) - -
11 PERFORM INITIALIZATION AND CALIBRATION - - - (Click here)
12 CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM - (Click here) - -

*A for Manual Tilt and Manual Telescopic Steering Column *B for Power Tilt and Power Telescopic Steering Column
*1 SPIRAL CABLE SUB-ASSEMBLY - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY

a.
B574512C03
0.333,0.583 6.833,2.5 6.5,1.917 0.927,1.323 1.5,1.323 true 4.958,1.24 4.958,0.719 4.958,0.719 4.531,0.719 true 4.323,1.302 4.896,1.302 true 0.583,1.417 1.531,1.417 true 3.583,2.5 3.583,0.583 false 4.896,1.75 4.813,2.083 4.813,2.083 4.813,1.833 true 1.5,1.771 1.417,2.104 1.417,2.104 1.417,1.854 true 0.375,0.625 0.708,0.948 0.333,0.323 12 false *A 3.615,0.615 4.021,0.969 0.406,0.354 12 false *B 0.76,1.229 1.073,1.385 0.313,0.156 10 false *a 4.76,2.094 4.938,2.271 0.177,0.177 10 true *b 0.396,1.323 0.708,1.479 0.313,0.156 10 false *c 4.344,0.635 4.656,0.792 0.313,0.156 10 false *d 4.146,1.208 4.458,1.365 0.313,0.156 10 false *a 1.344,2.104 1.521,2.281 0.177,0.177 10 true *b 0.594,0.208 0.927,0.531 0.333,0.323 18 false i
*A Colored Roller (Visible Type) *B Flat Cable (Visible Type)
*a Check Window *b Alignment Mark
*c Colored Roller *d Top of Flat Cable U-turn


i.

Check that the spiral cable sub-assembly is in the center position.

OK:

The connector is at the top.

The Alignment Mark are aligned.

The colored roller or the top of the flat cable U-turn can be checked from the check window.




b.
B573461C04
1.167,2 5.917,3.667 4.75,1.667 6.177,1.083 6.75,1.083 true 3.979,2.833 4.479,2.833 true 1.49,2.917 1.99,2.917 true 1.583,2.583 1.75,2.583 1.75,2.583 2.052,2.865 true 4.083,2.5 4.25,2.5 4.25,2.5 4.521,2.792 true 0.75,1.083 1.396,1.083 true 3.5,3.667 3.5,2 false 2.021,3.198 1.938,3.448 1.938,3.448 1.938,3.281 false 4.49,3.177 4.406,3.427 4.406,3.427 4.406,3.26 false 0.521,0.104 0.802,0.458 0.281,0.354 18 false i 2.854,0.469 3.135,0.823 0.281,0.354 18 false 2 5.146,0.458 5.427,0.813 0.281,0.354 18 false 3 0.854,1.99 1.135,2.344 0.281,0.354 18 false 4 1.219,2.063 1.594,2.302 0.375,0.24 12 false *A 3.542,2.052 3.917,2.292 0.375,0.24 12 false *B 6.813,1 7.052,1.156 0.24,0.156 10 false *a 3.771,2.76 4.01,2.917 0.24,0.156 10 false *b 1.292,2.844 1.531,3 0.24,0.156 10 false *b 1.354,2.51 1.594,2.667 0.24,0.156 10 false *d 3.875,2.427 4.115,2.583 0.24,0.156 10 false *e 4.354,3.448 4.542,3.604 0.188,0.156 10 true *c 1.875,3.469 2.063,3.625 0.188,0.156 10 true *c 0.542,1 0.781,1.156 0.24,0.156 10 false *a 0.573,0.51 0.854,0.865 0.281,0.354 18 false 1
*A Colored Roller (Visible Type) *B Flat Cable (Visible Type)
*a Interlock *b Check Window
*c Alignment Mark *d Colored Roller
*e Top of Flat Cable U-turn - -
V113147

Rotation Direction - -


i.

If the spiral cable sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable sub-assembly.

·

When rotating the spiral cable sub-assembly, make sure to push on the interlock to release the interlock.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



1. While pushing on the interlock indicated in the illustration, make sure to rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

Make sure to rotate the spiral cable sub-assembly counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.


HINT:

The interlock operates at the top and bottom of the connector.


2. If the spiral cable sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.

3. While pushing on the interlock, rotate the spiral cable sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.


4. Check that the spiral cable sub-assembly is in the center position.

OK:

The connector is at the top.

The Alignment Marks are aligned.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


NOTICE:

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.




Hide 89245B 2.INSTALL STEERING SENSOR

Z101186

HINT:

Perform this procedure only when replacement of the spiral cable sub-assembly is necessary.



a.
C436427C02
2.719,1.198 2.24,1.698 2.24,1.698 2.719,0.708 true 3.208,0.927 3.771,0.927 true 1.438,0.76 1.594,1.188 true 2.708,0.479 2.917,0.25 2.917,0.25 3.667,0.25 true 0.615,0.198 0.896,0.552 0.281,0.354 18 false i 4.594,0.542 4.875,0.896 0.281,0.354 18 false ii 2.125,1.708 2.302,1.917 0.177,0.208 10 true *a 3.802,0.844 4.021,1.031 0.219,0.188 10 true *b 1.531,1.208 1.708,1.406 0.177,0.198 10 true *b 3.698,0.167 3.917,0.354 0.219,0.188 10 true *c
*a Guide *b Pin
*c Lock Pin - -


i.

Align the pin and guide, and engage the claw to install the steering sensor to a new spiral cable sub-assembly.

NOTICE:
·

Do not remove the lock pin before the steering sensor is installed to the spiral cable sub-assembly.

·

Do not damage the claws or pins of the spiral cable sub-assembly or guides of the steering sensor.

·

The spiral cable sub-assembly can be rotated up to 30° even when the interlock is engaged. Therefore, make sure that both guides are aligned properly when installing the steering sensor to the spiral cable sub-assembly.




ii.

Remove the lock pin from the steering sensor.



Hide 3.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

a.
B611447


Hide 4.INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Z101186

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.

·

Do not rotate the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.

·

When rotating the spiral cable with sensor sub-assembly to check the operation of the spiral cable with sensor sub-assembly (checking for abnormal noise, checking the DTC, Data List, etc.) make sure to perform the inspection with the steering wheel assembly installed.




a.
B608600C01
0.583,0.667 1.167,0.667 true 4.208,0.094 4.531,0.417 0.323,0.323 18 false ii 0.438,0.563 0.708,0.771 0.271,0.208 10 false *a 0.625,0.094 0.948,0.417 0.323,0.323 18 false i
*a Turns off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
·

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B608730N01
0.542,0.104 0.823,0.458 0.281,0.354 18 false i 4.625,0.01 4.906,0.365 0.281,0.354 18 false ii

i.

Check that the front wheels are aligned facing straight ahead.


ii.

Set the turn signal switch to the neutral position.

NOTICE:

If it is not in the neutral position, the turn signal switch cancel ratchet may snap.




c.
B608728N01
0.25,0.063 0.531,0.417 0.281,0.354 18 false i 4.781,1.5 5.063,1.854 0.281,0.354 18 false iii 5.198,1.969 5.479,2.323 0.281,0.354 18 false ii 6.156,1.156 6.438,1.51 0.281,0.354 18 false ii 6.135,1.844 6.417,2.198 0.281,0.354 18 false ii 7,1.396 7.146,1.75 0.146,0.354 18 false ii

i.

Engage the claw, clip and clamp to install the spiral cable with sensor sub-assembly.


ii.

Connect the 4 connectors.


iii.

Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR




Hide 45286B 5.INSTALL UPPER STEERING COLUMN COVER

Hide 45024 6.INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY

Hide 7.ADJUST SPIRAL CABLE SUB-ASSEMBLY

Z101186

NOTICE:

Do not rotate the spiral cable sub-assembly with the battery connected and the ignition switch ON.



a.
B608600C01
0.583,0.667 1.167,0.667 true 4.208,0.094 4.531,0.417 0.323,0.323 18 false ii 0.438,0.563 0.708,0.771 0.271,0.208 10 false *a 0.625,0.094 0.948,0.417 0.323,0.323 18 false i
*a Turns off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
·

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B574511C01
0.052,0.5 6.917,2.583 6.865,2.083 0.271,1.354 0.74,1.354 0.74,1.354 0.74,1.594 true 0.75,1.802 0.75,2.406 true 3.656,1.292 4.188,1.292 4.188,1.292 4.188,1.521 true 4.146,1.688 4.146,2.292 true 3.417,2.583 3.417,0.5 false 0.115,0.583 0.417,0.833 0.302,0.25 12 false *A 3.448,0.583 3.781,0.896 0.333,0.313 12 false *B 0.104,1.281 0.365,1.49 0.26,0.208 10 false *a 0.677,2.438 0.938,2.646 0.26,0.208 10 false *b 4.063,2.323 4.323,2.615 0.26,0.292 10 false *c 3.479,1.208 3.792,1.365 0.313,0.156 10 false *a 0.417,0.115 0.719,0.365 0.302,0.25 18 false i
*A Colored Roller (Visible Type) *B Flat Cable (Visible Type)
*a Check Window *b Colored Roller
*c Top of Flat Cable U-turn - -


i.

Check that the spiral cable sub-assembly is in the center position.

OK:

The connector is at the top.

The colored roller or the top of the flat cable U-turn can be checked from the check window.




c.
B573462C02
0.667,2.167 6.333,3.75 5.667,1.583 0.917,3.333 1.26,3.333 true 0.917,2.833 1.083,2.833 1.083,2.833 1.333,3.271 true 3.833,2.833 4,2.833 4,2.833 4.083,3.271 true 0.417,1.083 1.083,1.083 true 3.833,3.646 4,3.646 4,3.646 4.083,3.396 true 3.5,3.75 3.5,2.167 false 0.49,0.115 0.771,0.469 0.281,0.354 18 false i 2.802,0.479 3.083,0.833 0.281,0.354 18 false 2 5.052,0.479 5.333,0.833 0.281,0.354 18 false 3 0.219,2 0.5,2.354 0.281,0.354 18 false 4 0.708,2.25 1.083,2.49 0.375,0.24 12 false *A 3.531,2.25 3.906,2.49 0.375,0.24 12 false *B 3.688,3.573 3.927,3.729 0.24,0.156 10 false *b 0.75,3.26 0.99,3.417 0.24,0.156 10 false *b 3.667,2.76 3.906,2.917 0.24,0.156 10 false *d 0.729,2.771 0.917,2.927 0.188,0.156 10 false *c 0.198,1.01 0.438,1.167 0.24,0.156 10 false *a 0.344,0.479 0.625,0.833 0.281,0.354 18 false 1
*A Colored Roller (Visible Type) *B Flat Cable (Visible Type)
*a Interlock *b Check Window
*c Colored Roller *d Top of Flat Cable U-turn
V113147

Rotation Direction - -


i.

If the spiral cable sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable sub-assembly.

·

When rotating the spiral cable sub-assembly, make sure to push on the interlock to release the interlock.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



1. While pushing on the interlock indicated in the illustration. Make sure to rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

Make sure to rotate the spiral cable sub-assembly counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.


HINT:

The interlock operates at the top and bottom of the connector.


2. If the spiral cable sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.

3. While pushing on the interlock, rotate the spiral cable sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.


4. Check that the spiral cable sub-assembly is in the center position.

OK:

The connector is at the top.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


NOTICE:

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.




Hide 45100 8.INSTALL STEERING WHEEL ASSEMBLY

Hide 9. PERFORM DIAGNOSTIC SYSTEM CHECK

Hide 11.PERFORM INITIALIZATION AND CALIBRATION

Hide 12. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM (for Power Tilt and Power Telescopic Steering Column)

Z101186

Click here(Click here)