Home › Audio / Visual / Telematics › AUDIO / VIDEO › ACTIVE NOISE CONTROL SYSTEM (for Type B)
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467500 ACTIVE NOISE CONTROL SYSTEM(for Type B) J

AUDIO / VIDEO  ACTIVE NOISE CONTROL SYSTEM(for Type B)  Mute Signal Circuit between Stereo Component Equalizer and Telematics Transceiver  


DESCRIPTION

This telephone transceiver assembly sends a mute signal to the stereo component equalizer assembly. The stereo component equalizer assembly controls the volume according to the mute signal from the telephone transceiver assembly.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component equalizer assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E422235E33
4.615,2.083 7.135,2.323 2.521,0.24 10 false Stereo Component Equalizer Assembly 4.635,1.906 5.094,2.104 0.458,0.198 10 false S25 0.625,1.927 1.083,2.125 0.458,0.198 10 false I55 0.646,2.115 3.323,2.396 2.677,0.281 10 false Telephone Transceiver Assembly 5.542,1.031 5.979,1.229 0.438,0.198 10 false TMUT 1.219,1.031 1.667,1.24 0.448,0.208 10 false MUTE 1.771,0.885 2.01,1.094 0.24,0.208 10 false 14 5.26,0.906 5.479,1.115 0.219,0.208 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

When replacing the telephone transceiver assembly, make sure to replace it with a new one.


PROCEDURE

1.INSPECT TELEPHONE TRANSCEIVER ASSEMBLY
a.
E427105C70
1.531,0.563 2.052,0.865 0.521,0.302 0.792,0.948 0.969,0.948 0.969,0.948 1.052,1.708 false 1.677,0.635 2.292,0.833 0.615,0.198 10 false I55 0.271,0.104 0.885,0.302 0.615,0.198 10 false *a 0.365,0.865 0.979,1.063 0.615,0.198 10 false MUTE
*a Component with harness connected
(Telephone Transceiver Assembly)


Remove the telephone transceiver assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I55)Location & Routing

Click Connector(I55)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Telematics Transceiver Assembly

I55-14 (MUTE) - Body ground Ignition switch ON, audio system playing
→ Emergency call mode
3 to 5 V → Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY - TELEPHONE TRANSCEIVER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY - TELEPHONE TRANSCEIVER ASSEMBLY)
a.

Disconnect the S25 stereo component equalizer assembly connector.


b.

Disconnect the I55 telephone transceiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(S25,I55)Location & Routing

Click Connector(S25)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Equalizer Assembly

Click Connector(I55)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Telematics Transceiver Assembly

S25-4 (TMUT) - I55-14 (MUTE) Always Below 1 Ω
S25-4 (TMUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK STEREO COMPONENT EQUALIZER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STEREO COMPONENT EQUALIZER ASSEMBLY
a.

Disconnect the I55 telephone transceiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I55)Location & Routing

Click Connector(I55)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Telematics Transceiver Assembly

I55-14 (MUTE) - Body ground Ignition switch ON 3.0 to 5.0 V



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPLACE STEREO COMPONENT EQUALIZER ASSEMBLY