Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0467922 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B007512  Second Row Right Seat Belt Pretensioner Deployment Control Circuit Short to Battery  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B007512 Second Row Right Seat Belt Pretensioner Deployment Control Circuit Short to Battery One of the following conditions is met:
·

The airbag ECU assembly detects a short to B+ in the right side 2nd seat pretensioner squib circuit for 0.5 seconds.

·

A rear seat outer belt assembly RH malfunction.

·

An airbag ECU assembly malfunction.


·

Wire harness

·

Rear seat outer belt assembly RH

·

Airbag ECU assembly


Comes on SRS Airbag A Applicable

WIRING DIAGRAM

C284375E74
5.354,1.792 5.688,1.979 0.333,0.188 10 false Q1 5.396,0.458 5.5,0.604 0.104,0.146 10 false 5 5.646,0.542 6.042,0.719 0.396,0.177 10 false PRR+ 5.396,1.229 5.5,1.375 0.104,0.146 10 false 6 1.729,1.25 1.906,1.417 0.177,0.167 10 false 2 1.708,0.458 1.927,0.688 0.219,0.229 10 false 1 5.635,1.396 6.083,1.573 0.448,0.177 10 false PRR- 1.323,0.448 1.688,0.615 0.365,0.167 10 false RR+ 1.313,1.219 1.604,1.375 0.292,0.156 10 false RR- 5.365,1.979 6.844,2.448 1.479,0.469 10 false Airbag ECU Assembly 0.052,1.76 0.698,1.938 0.646,0.177 10 false Q17 0.052,1.958 2.813,2.25 2.76,0.292 10 false Rear No. 1 Seat Outer Belt Assembly RH

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS ( Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
DTC B007512 is output A
Past DTC B007512 is output B


Post-procedure1

c.

None



A

2.CHECK CONNECTION OF CONNECTORS

B

USE SIMULATION METHOD TO CHECK

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

HINT:
·

To perform the simulation method, enter check mode (signal check) with the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

Perform the simulation method while checking the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST




2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


Procedure1

c.

Check that the connectors are properly connected to the rear No. 1 seat outer belt assembly RH and airbag ECU assembly.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS

Pre-procedure1

a.
C400937C02
0.625,1.104 0.938,1.302 0.313,0.198 10 false *1 1.24,1.094 1.552,1.292 0.313,0.198 10 false *3 2.229,1.677 2.542,1.875 0.313,0.198 10 false *2
*1 Rear No. 1 Seat Outer Belt Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness


Disconnect the airbag ECU assembly connector.


b.

Disconnect the rear No. 1 seat outer belt assembly RH connector.


Procedure1

c.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.



d.

Check that the connectors are not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



e.

Check that the short springs of the activation prevention mechanisms of the wire harness connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

f.

None



OK

4.CHECK REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH
a.
B612270C05
0.396,2.26 0.833,2.5 0.438,0.24 2.094,3.063 1.938,3.063 1.938,3.063 1.781,2.813 true 0.656,1.188 0.969,1.344 0.313,0.156 10 false *1 2.25,1.292 2.563,1.448 0.313,0.156 10 false *2 2.177,2.99 2.49,3.146 0.313,0.156 10 false *4 0.375,1.896 0.688,2.052 0.313,0.156 10 false *a 1.823,0.979 2.021,1.146 0.198,0.167 10 false A 1.667,0.969 1.865,1.177 0.198,0.208 10 false B 1.167,0.958 1.344,1.156 0.177,0.198 10 false C 0.813,0.958 1,1.156 0.188,0.198 10 false D 0.5,2.313 0.813,2.469 0.313,0.156 10 false Q17 1.354,1.208 1.667,1.365 0.313,0.156 10 false *3
*1 Rear No. 1 Seat Outer Belt Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness
*4 SST
*a Front view of wire harness connector
(to Rear No. 1 Seat Outer Belt Assembly RH)


Connect the Q1 airbag ECU assembly connector.


b.

Connect the white wire side of SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the rear No. 1 seat outer belt assembly RH for measurement, as this may lead to a serious injury due to pretensioner deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

5.CHECK REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH
5.CHECK REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

c.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B007512 is not output A
DTC B007512 is output B



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


f.

Disconnect SST from connector C.



A

REPLACE REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

B

6.CHECK HARNESS AND CONNECTOR
6.CHECK HARNESS AND CONNECTOR

Pre-procedure1

a.
B612271C04
0.51,2.354 0.927,2.604 0.417,0.25 0.854,2.958 1.063,2.958 1.063,2.958 1.313,2.51 true 1.469,2.531 1.75,2.958 1.75,2.958 2,2.958 true 0.563,1.188 0.875,1.344 0.313,0.156 10 false *1 2.25,1.292 2.563,1.448 0.313,0.156 10 false *2 1.219,1.156 1.531,1.313 0.313,0.156 10 false *3 0.323,1.896 0.635,2.115 0.313,0.219 10 false *a 0.583,2.396 0.958,2.615 0.375,0.219 10 false Q17 1.833,0.958 2.031,1.146 0.198,0.188 10 false A 1.521,0.969 1.719,1.177 0.198,0.208 10 false B 1.021,0.969 1.219,1.146 0.198,0.177 10 false C 0.688,0.969 0.844,1.146 0.156,0.177 10 false D 0.521,2.885 1.01,3.083 0.49,0.198 10 false RR+ 2.042,2.875 2.417,3.052 0.375,0.177 10 false RR-
*1 Rear No. 1 Seat Outer Belt Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Rear No. 1 Seat Outer Belt Assembly RH)


Disconnect the Q1 airbag ECU assembly connector.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(Q17)Location & Routing

Click Connector(Q17)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Seat Belt Pretensioner RH (Rear No. 1 Seat Belt Assembly Outer RH)

Q17-1 (RR+) - Body ground Ignition switch ON Below 1 V
Q17-2 (RR-) - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.



OK

7.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CLEAR DTC
a.
C400942C06
0.896,1.531 1.208,1.688 0.313,0.156 10 false *1 2.24,1.594 2.552,1.75 0.313,0.156 10 false *2 1.365,1.521 1.677,1.677 0.313,0.156 10 false *3
*1 Rear No. 1 Seat Outer Belt Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness


Connect the airbag ECU assembly connector.


b.

Connect the rear No. 1 seat outer belt assembly RH connector.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

8.CHECK DTC
8.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

c.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B007512 is not output A
DTC B007512 is output B



Post-procedure1

d.

None



A

USE SIMULATION METHOD TO CHECK

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

HINT:
·

To perform the simulation method, enter check mode (signal check) with the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

Perform the simulation method while checking the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST




B